From b3ddf6904073990492454b1dd1c10a24be8c74c6 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 12 Feb 2024 13:58:33 +0100 Subject: [PATCH 001/107] batman-adv: Avoid infinite loop trying to resize local TT commit b1f532a3b1e6d2e5559c7ace49322922637a28aa upstream. If the MTU of one of an attached interface becomes too small to transmit the local translation table then it must be resized to fit inside all fragments (when enabled) or a single packet. But if the MTU becomes too low to transmit even the header + the VLAN specific part then the resizing of the local TT will never succeed. This can for example happen when the usable space is 110 bytes and 11 VLANs are on top of batman-adv. In this case, at least 116 byte would be needed. There will just be an endless spam of batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110) in the log but the function will never finish. Problem here is that the timeout will be halved all the time and will then stagnate at 0 and therefore never be able to reduce the table even more. There are other scenarios possible with a similar result. The number of BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too high to fit inside a packet. Such a scenario can therefore happen also with only a single VLAN + 7 non-purgable addresses - requiring at least 120 bytes. While this should be handled proactively when: * interface with too low MTU is added * VLAN is added * non-purgeable local mac is added * MTU of an attached interface is reduced * fragmentation setting gets disabled (which most likely requires dropping attached interfaces) not all of these scenarios can be prevented because batman-adv is only consuming events without the the possibility to prevent these actions (non-purgable MAC address added, MTU of an attached interface is reduced). It is therefore necessary to also make sure that the code is able to handle also the situations when there were already incompatible system configuration are present. Cc: stable@vger.kernel.org Fixes: a19d3d85e1b8 ("batman-adv: limit local translation table max size") Reported-by: syzbot+a6a4b5bb3da165594cff@syzkaller.appspotmail.com Signed-off-by: Sven Eckelmann Signed-off-by: Simon Wunderlich Signed-off-by: Greg Kroah-Hartman --- net/batman-adv/translation-table.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/batman-adv/translation-table.c b/net/batman-adv/translation-table.c index a01b0277bdb1..38930eccd9df 100644 --- a/net/batman-adv/translation-table.c +++ b/net/batman-adv/translation-table.c @@ -4190,7 +4190,7 @@ void batadv_tt_local_resize_to_mtu(struct net_device *soft_iface) spin_lock_bh(&bat_priv->tt.commit_lock); - while (true) { + while (timeout) { table_size = batadv_tt_local_table_transmit_size(bat_priv); if (packet_size_max >= table_size) break; From 4beab84fbb50df3be1d8f8a976e6fe882ca65cb2 Mon Sep 17 00:00:00 2001 From: Dmitry Antipov Date: Tue, 2 Apr 2024 14:32:05 +0300 Subject: [PATCH 002/107] Bluetooth: Fix memory leak in hci_req_sync_complete() commit 45d355a926ab40f3ae7bc0b0a00cb0e3e8a5a810 upstream. In 'hci_req_sync_complete()', always free the previous sync request state before assigning reference to a new one. Reported-by: syzbot+39ec16ff6cc18b1d066d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=39ec16ff6cc18b1d066d Cc: stable@vger.kernel.org Fixes: f60cb30579d3 ("Bluetooth: Convert hci_req_sync family of function to new request API") Signed-off-by: Dmitry Antipov Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman --- net/bluetooth/hci_request.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/bluetooth/hci_request.c b/net/bluetooth/hci_request.c index 7f3f4ea56d44..9da32a120231 100644 --- a/net/bluetooth/hci_request.c +++ b/net/bluetooth/hci_request.c @@ -107,8 +107,10 @@ static void hci_req_sync_complete(struct hci_dev *hdev, u8 result, u16 opcode, if (hdev->req_status == HCI_REQ_PEND) { hdev->req_result = result; hdev->req_status = HCI_REQ_DONE; - if (skb) + if (skb) { + kfree_skb(hdev->req_skb); hdev->req_skb = skb_get(skb); + } wake_up_interruptible(&hdev->req_wait_q); } } From ccabbf1d9df45ebfb73d82436d2b9c719544da51 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Thu, 4 Apr 2024 18:02:25 +0200 Subject: [PATCH 003/107] nouveau: fix function cast warning [ Upstream commit 185fdb4697cc9684a02f2fab0530ecdd0c2f15d4 ] Calling a function through an incompatible pointer type causes breaks kcfi, so clang warns about the assignment: drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c:73:10: error: cast from 'void (*)(const void *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict] 73 | .fini = (void(*)(void *))kfree, Avoid this with a trivial wrapper. Fixes: c39f472e9f14 ("drm/nouveau: remove symlinks, move core/ to nvkm/ (no code changes)") Signed-off-by: Arnd Bergmann Signed-off-by: Danilo Krummrich Link: https://patchwork.freedesktop.org/patch/msgid/20240404160234.2923554-1-arnd@kernel.org Signed-off-by: Sasha Levin --- drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c b/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c index 4bf486b57101..cb05f7f48a98 100644 --- a/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c +++ b/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c @@ -66,11 +66,16 @@ of_init(struct nvkm_bios *bios, const char *name) return ERR_PTR(-EINVAL); } +static void of_fini(void *p) +{ + kfree(p); +} + const struct nvbios_source nvbios_of = { .name = "OpenFirmware", .init = of_init, - .fini = (void(*)(void *))kfree, + .fini = of_fini, .read = of_read, .size = of_size, .rw = false, From e7d818b8ccfb250999e46f54dd9f29e7fabae39a Mon Sep 17 00:00:00 2001 From: Ilya Maximets Date: Wed, 3 Apr 2024 22:38:01 +0200 Subject: [PATCH 004/107] net: openvswitch: fix unwanted error log on timeout policy probing [ Upstream commit 4539f91f2a801c0c028c252bffae56030cfb2cae ] On startup, ovs-vswitchd probes different datapath features including support for timeout policies. While probing, it tries to execute certain operations with OVS_PACKET_ATTR_PROBE or OVS_FLOW_ATTR_PROBE attributes set. These attributes tell the openvswitch module to not log any errors when they occur as it is expected that some of the probes will fail. For some reason, setting the timeout policy ignores the PROBE attribute and logs a failure anyway. This is causing the following kernel log on each re-start of ovs-vswitchd: kernel: Failed to associated timeout policy `ovs_test_tp' Fix that by using the same logging macro that all other messages are using. The message will still be printed at info level when needed and will be rate limited, but with a net rate limiter instead of generic printk one. The nf_ct_set_timeout() itself will still print some info messages, but at least this change makes logging in openvswitch module more consistent. Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action") Signed-off-by: Ilya Maximets Acked-by: Eelco Chaudron Link: https://lore.kernel.org/r/20240403203803.2137962-1-i.maximets@ovn.org Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- net/openvswitch/conntrack.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/net/openvswitch/conntrack.c b/net/openvswitch/conntrack.c index 78448b6888dd..90c5f5300728 100644 --- a/net/openvswitch/conntrack.c +++ b/net/openvswitch/conntrack.c @@ -1687,8 +1687,9 @@ int ovs_ct_copy_action(struct net *net, const struct nlattr *attr, if (ct_info.timeout[0]) { if (nf_ct_set_timeout(net, ct_info.ct, family, key->ip.proto, ct_info.timeout)) - pr_info_ratelimited("Failed to associated timeout " - "policy `%s'\n", ct_info.timeout); + OVS_NLERR(log, + "Failed to associated timeout policy '%s'", + ct_info.timeout); else ct_info.nf_ct_timeout = rcu_dereference( nf_ct_timeout_find(ct_info.ct)->timeout); From 2f75517633608228fd3c49f6b8c5dbc8f8490e2e Mon Sep 17 00:00:00 2001 From: Petr Tesarik Date: Thu, 4 Apr 2024 09:57:40 +0200 Subject: [PATCH 005/107] u64_stats: fix u64_stats_init() for lockdep when used repeatedly in one file [ Upstream commit 38a15d0a50e0a43778561a5861403851f0b0194c ] Fix bogus lockdep warnings if multiple u64_stats_sync variables are initialized in the same file. With CONFIG_LOCKDEP, seqcount_init() is a macro which declares: static struct lock_class_key __key; Since u64_stats_init() is a function (albeit an inline one), all calls within the same file end up using the same instance, effectively treating them all as a single lock-class. Fixes: 9464ca650008 ("net: make u64_stats_init() a function") Closes: https://lore.kernel.org/netdev/ea1567d9-ce66-45e6-8168-ac40a47d1821@roeck-us.net/ Signed-off-by: Petr Tesarik Reviewed-by: Simon Horman Reviewed-by: Eric Dumazet Link: https://lore.kernel.org/r/20240404075740.30682-1-petr@tesarici.cz Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- include/linux/u64_stats_sync.h | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/include/linux/u64_stats_sync.h b/include/linux/u64_stats_sync.h index 11096b561dab..ca40163933e3 100644 --- a/include/linux/u64_stats_sync.h +++ b/include/linux/u64_stats_sync.h @@ -70,7 +70,11 @@ struct u64_stats_sync { #if BITS_PER_LONG == 32 && defined(CONFIG_SMP) -#define u64_stats_init(syncp) seqcount_init(&(syncp)->seq) +#define u64_stats_init(syncp) \ + do { \ + struct u64_stats_sync *__s = (syncp); \ + seqcount_init(&__s->seq); \ + } while (0) #else static inline void u64_stats_init(struct u64_stats_sync *syncp) { From d3adf11d7993518a39bd02b383cfe657ccc0023c Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 5 Apr 2024 10:30:34 +0000 Subject: [PATCH 006/107] geneve: fix header validation in geneve[6]_xmit_skb [ Upstream commit d8a6213d70accb403b82924a1c229e733433a5ef ] syzbot is able to trigger an uninit-value in geneve_xmit() [1] Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield()) uses skb_protocol(skb, true), pskb_inet_may_pull() is only using skb->protocol. If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol, pskb_inet_may_pull() does nothing at all. If a vlan tag was provided by the caller (af_packet in the syzbot case), the network header might not point to the correct location, and skb linear part could be smaller than expected. Add skb_vlan_inet_prepare() to perform a complete mac validation. Use this in geneve for the moment, I suspect we need to adopt this more broadly. v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest - Only call __vlan_get_protocol() for vlan types. Link: https://lore.kernel.org/netdev/20240404100035.3270a7d5@kernel.org/ v2,v3 - Addressed Sabrina comments on v1 and v2 Link: https://lore.kernel.org/netdev/Zg1l9L2BNoZWZDZG@hog/ [1] BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline] BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 geneve_xmit_skb drivers/net/geneve.c:910 [inline] geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335 dev_queue_xmit include/linux/netdevice.h:3091 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795 packet_alloc_skb net/packet/af_packet.c:2930 [inline] packet_snd net/packet/af_packet.c:3024 [inline] packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 Fixes: d13f048dd40e ("net: geneve: modify IP header check in geneve6_xmit_skb and geneve_xmit_skb") Reported-by: syzbot+9ee20ec1de7b3168db09@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/000000000000d19c3a06152f9ee4@google.com/ Signed-off-by: Eric Dumazet Cc: Phillip Potter Cc: Sabrina Dubroca Reviewed-by: Sabrina Dubroca Reviewed-by: Phillip Potter Signed-off-by: David S. Miller Signed-off-by: Sasha Levin --- drivers/net/geneve.c | 4 ++-- include/net/ip_tunnels.h | 33 +++++++++++++++++++++++++++++++++ 2 files changed, 35 insertions(+), 2 deletions(-) diff --git a/drivers/net/geneve.c b/drivers/net/geneve.c index f932e4120cb6..961cbd2b377d 100644 --- a/drivers/net/geneve.c +++ b/drivers/net/geneve.c @@ -904,7 +904,7 @@ static int geneve_xmit_skb(struct sk_buff *skb, struct net_device *dev, __be16 sport; int err; - if (!pskb_inet_may_pull(skb)) + if (!skb_vlan_inet_prepare(skb)) return -EINVAL; sport = udp_flow_src_port(geneve->net, skb, 1, USHRT_MAX, true); @@ -970,7 +970,7 @@ static int geneve6_xmit_skb(struct sk_buff *skb, struct net_device *dev, __be16 sport; int err; - if (!pskb_inet_may_pull(skb)) + if (!skb_vlan_inet_prepare(skb)) return -EINVAL; sport = udp_flow_src_port(geneve->net, skb, 1, USHRT_MAX, true); diff --git a/include/net/ip_tunnels.h b/include/net/ip_tunnels.h index 36376f8b84da..3a04e2ccfb39 100644 --- a/include/net/ip_tunnels.h +++ b/include/net/ip_tunnels.h @@ -329,6 +329,39 @@ static inline bool pskb_inet_may_pull(struct sk_buff *skb) return pskb_network_may_pull(skb, nhlen); } +/* Variant of pskb_inet_may_pull(). + */ +static inline bool skb_vlan_inet_prepare(struct sk_buff *skb) +{ + int nhlen = 0, maclen = ETH_HLEN; + __be16 type = skb->protocol; + + /* Essentially this is skb_protocol(skb, true) + * And we get MAC len. + */ + if (eth_type_vlan(type)) + type = __vlan_get_protocol(skb, type, &maclen); + + switch (type) { +#if IS_ENABLED(CONFIG_IPV6) + case htons(ETH_P_IPV6): + nhlen = sizeof(struct ipv6hdr); + break; +#endif + case htons(ETH_P_IP): + nhlen = sizeof(struct iphdr); + break; + } + /* For ETH_P_IPV6/ETH_P_IP we make sure to pull + * a base network header in skb->head. + */ + if (!pskb_may_pull(skb, maclen + nhlen)) + return false; + + skb_set_network_header(skb, maclen); + return true; +} + static inline int ip_encap_hlen(struct ip_tunnel_encap *e) { const struct ip_tunnel_encap_ops *ops; From e9f4cfe42fe44325201369180adbd887ab4b93ad Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Mon, 8 Apr 2024 09:42:02 +0200 Subject: [PATCH 007/107] ipv6: fib: hide unused 'pn' variable [ Upstream commit 74043489fcb5e5ca4074133582b5b8011b67f9e7 ] When CONFIG_IPV6_SUBTREES is disabled, the only user is hidden, causing a 'make W=1' warning: net/ipv6/ip6_fib.c: In function 'fib6_add': net/ipv6/ip6_fib.c:1388:32: error: variable 'pn' set but not used [-Werror=unused-but-set-variable] Add another #ifdef around the variable declaration, matching the other uses in this file. Fixes: 66729e18df08 ("[IPV6] ROUTE: Make sure we have fn->leaf when adding a node on subtree.") Link: https://lore.kernel.org/netdev/20240322131746.904943-1-arnd@kernel.org/ Reviewed-by: David Ahern Signed-off-by: Arnd Bergmann Reviewed-by: Eric Dumazet Link: https://lore.kernel.org/r/20240408074219.3030256-1-arnd@kernel.org Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin --- net/ipv6/ip6_fib.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/net/ipv6/ip6_fib.c b/net/ipv6/ip6_fib.c index 7d593e50977c..3afc32fe9b07 100644 --- a/net/ipv6/ip6_fib.c +++ b/net/ipv6/ip6_fib.c @@ -1307,7 +1307,10 @@ int fib6_add(struct fib6_node *root, struct fib6_info *rt, struct nl_info *info, struct netlink_ext_ack *extack) { struct fib6_table *table = rt->fib6_table; - struct fib6_node *fn, *pn = NULL; + struct fib6_node *fn; +#ifdef CONFIG_IPV6_SUBTREES + struct fib6_node *pn = NULL; +#endif int err = -ENOMEM; int allow_create = 1; int replace_required = 0; @@ -1331,9 +1334,9 @@ int fib6_add(struct fib6_node *root, struct fib6_info *rt, goto out; } +#ifdef CONFIG_IPV6_SUBTREES pn = fn; -#ifdef CONFIG_IPV6_SUBTREES if (rt->fib6_src.plen) { struct fib6_node *sn; From 3af3f21d01495bc6792bdd8b834bdf291777dad8 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Mon, 8 Apr 2024 09:42:03 +0200 Subject: [PATCH 008/107] ipv4/route: avoid unused-but-set-variable warning [ Upstream commit cf1b7201df59fb936f40f4a807433fe3f2ce310a ] The log_martians variable is only used in an #ifdef, causing a 'make W=1' warning with gcc: net/ipv4/route.c: In function 'ip_rt_send_redirect': net/ipv4/route.c:880:13: error: variable 'log_martians' set but not used [-Werror=unused-but-set-variable] Change the #ifdef to an equivalent IS_ENABLED() to let the compiler see where the variable is used. Fixes: 30038fc61adf ("net: ip_rt_send_redirect() optimization") Reviewed-by: David Ahern Signed-off-by: Arnd Bergmann Reviewed-by: Eric Dumazet Link: https://lore.kernel.org/r/20240408074219.3030256-2-arnd@kernel.org Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin --- net/ipv4/route.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/net/ipv4/route.c b/net/ipv4/route.c index 902296ef3e5a..5b008d838e2b 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -945,13 +945,11 @@ void ip_rt_send_redirect(struct sk_buff *skb) icmp_send(skb, ICMP_REDIRECT, ICMP_REDIR_HOST, gw); peer->rate_last = jiffies; ++peer->n_redirects; -#ifdef CONFIG_IP_ROUTE_VERBOSE - if (log_martians && + if (IS_ENABLED(CONFIG_IP_ROUTE_VERBOSE) && log_martians && peer->n_redirects == ip_rt_redirect_number) net_warn_ratelimited("host %pI4/if%d ignores redirects for %pI4 to %pI4\n", &ip_hdr(skb)->saddr, inet_iif(skb), &ip_hdr(skb)->daddr, &gw); -#endif } out_put_peer: inet_putpeer(peer); From cca606e14264098cba65efa82790825dbf69e903 Mon Sep 17 00:00:00 2001 From: Jiri Benc Date: Mon, 8 Apr 2024 16:18:21 +0200 Subject: [PATCH 009/107] ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr [ Upstream commit 7633c4da919ad51164acbf1aa322cc1a3ead6129 ] Although ipv6_get_ifaddr walks inet6_addr_lst under the RCU lock, it still means hlist_for_each_entry_rcu can return an item that got removed from the list. The memory itself of such item is not freed thanks to RCU but nothing guarantees the actual content of the memory is sane. In particular, the reference count can be zero. This can happen if ipv6_del_addr is called in parallel. ipv6_del_addr removes the entry from inet6_addr_lst (hlist_del_init_rcu(&ifp->addr_lst)) and drops all references (__in6_ifa_put(ifp) + in6_ifa_put(ifp)). With bad enough timing, this can happen: 1. In ipv6_get_ifaddr, hlist_for_each_entry_rcu returns an entry. 2. Then, the whole ipv6_del_addr is executed for the given entry. The reference count drops to zero and kfree_rcu is scheduled. 3. ipv6_get_ifaddr continues and tries to increments the reference count (in6_ifa_hold). 4. The rcu is unlocked and the entry is freed. 5. The freed entry is returned. Prevent increasing of the reference count in such case. The name in6_ifa_hold_safe is chosen to mimic the existing fib6_info_hold_safe. [ 41.506330] refcount_t: addition on 0; use-after-free. [ 41.506760] WARNING: CPU: 0 PID: 595 at lib/refcount.c:25 refcount_warn_saturate+0xa5/0x130 [ 41.507413] Modules linked in: veth bridge stp llc [ 41.507821] CPU: 0 PID: 595 Comm: python3 Not tainted 6.9.0-rc2.main-00208-g49563be82afa #14 [ 41.508479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) [ 41.509163] RIP: 0010:refcount_warn_saturate+0xa5/0x130 [ 41.509586] Code: ad ff 90 0f 0b 90 90 c3 cc cc cc cc 80 3d c0 30 ad 01 00 75 a0 c6 05 b7 30 ad 01 01 90 48 c7 c7 38 cc 7a 8c e8 cc 18 ad ff 90 <0f> 0b 90 90 c3 cc cc cc cc 80 3d 98 30 ad 01 00 0f 85 75 ff ff ff [ 41.510956] RSP: 0018:ffffbda3c026baf0 EFLAGS: 00010282 [ 41.511368] RAX: 0000000000000000 RBX: ffff9e9c46914800 RCX: 0000000000000000 [ 41.511910] RDX: ffff9e9c7ec29c00 RSI: ffff9e9c7ec1c900 RDI: ffff9e9c7ec1c900 [ 41.512445] RBP: ffff9e9c43660c9c R08: 0000000000009ffb R09: 00000000ffffdfff [ 41.512998] R10: 00000000ffffdfff R11: ffffffff8ca58a40 R12: ffff9e9c4339a000 [ 41.513534] R13: 0000000000000001 R14: ffff9e9c438a0000 R15: ffffbda3c026bb48 [ 41.514086] FS: 00007fbc4cda1740(0000) GS:ffff9e9c7ec00000(0000) knlGS:0000000000000000 [ 41.514726] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 41.515176] CR2: 000056233b337d88 CR3: 000000000376e006 CR4: 0000000000370ef0 [ 41.515713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 41.516252] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 41.516799] Call Trace: [ 41.517037] [ 41.517249] ? __warn+0x7b/0x120 [ 41.517535] ? refcount_warn_saturate+0xa5/0x130 [ 41.517923] ? report_bug+0x164/0x190 [ 41.518240] ? handle_bug+0x3d/0x70 [ 41.518541] ? exc_invalid_op+0x17/0x70 [ 41.520972] ? asm_exc_invalid_op+0x1a/0x20 [ 41.521325] ? refcount_warn_saturate+0xa5/0x130 [ 41.521708] ipv6_get_ifaddr+0xda/0xe0 [ 41.522035] inet6_rtm_getaddr+0x342/0x3f0 [ 41.522376] ? __pfx_inet6_rtm_getaddr+0x10/0x10 [ 41.522758] rtnetlink_rcv_msg+0x334/0x3d0 [ 41.523102] ? netlink_unicast+0x30f/0x390 [ 41.523445] ? __pfx_rtnetlink_rcv_msg+0x10/0x10 [ 41.523832] netlink_rcv_skb+0x53/0x100 [ 41.524157] netlink_unicast+0x23b/0x390 [ 41.524484] netlink_sendmsg+0x1f2/0x440 [ 41.524826] __sys_sendto+0x1d8/0x1f0 [ 41.525145] __x64_sys_sendto+0x1f/0x30 [ 41.525467] do_syscall_64+0xa5/0x1b0 [ 41.525794] entry_SYSCALL_64_after_hwframe+0x72/0x7a [ 41.526213] RIP: 0033:0x7fbc4cfcea9a [ 41.526528] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 [ 41.527942] RSP: 002b:00007ffcf54012a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c [ 41.528593] RAX: ffffffffffffffda RBX: 00007ffcf5401368 RCX: 00007fbc4cfcea9a [ 41.529173] RDX: 000000000000002c RSI: 00007fbc4b9d9bd0 RDI: 0000000000000005 [ 41.529786] RBP: 00007fbc4bafb040 R08: 00007ffcf54013e0 R09: 000000000000000c [ 41.530375] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 41.530977] R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007fbc4ca85d1b [ 41.531573] Fixes: 5c578aedcb21d ("IPv6: convert addrconf hash list to RCU") Reviewed-by: Eric Dumazet Reviewed-by: David Ahern Signed-off-by: Jiri Benc Link: https://lore.kernel.org/r/8ab821e36073a4a406c50ec83c9e8dc586c539e4.1712585809.git.jbenc@redhat.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- include/net/addrconf.h | 4 ++++ net/ipv6/addrconf.c | 7 ++++--- 2 files changed, 8 insertions(+), 3 deletions(-) diff --git a/include/net/addrconf.h b/include/net/addrconf.h index 32685eaba28f..95990fa93d2f 100644 --- a/include/net/addrconf.h +++ b/include/net/addrconf.h @@ -431,6 +431,10 @@ static inline void in6_ifa_hold(struct inet6_ifaddr *ifp) refcount_inc(&ifp->refcnt); } +static inline bool in6_ifa_hold_safe(struct inet6_ifaddr *ifp) +{ + return refcount_inc_not_zero(&ifp->refcnt); +} /* * compute link-local solicited-node multicast address diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index 974e650e749e..2720e5d931e8 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -2026,9 +2026,10 @@ struct inet6_ifaddr *ipv6_get_ifaddr(struct net *net, const struct in6_addr *add if (ipv6_addr_equal(&ifp->addr, addr)) { if (!dev || ifp->idev->dev == dev || !(ifp->scope&(IFA_LINK|IFA_HOST) || strict)) { - result = ifp; - in6_ifa_hold(ifp); - break; + if (in6_ifa_hold_safe(ifp)) { + result = ifp; + break; + } } } } From 1263b0b26077b1183c3c45a0a2479573a351d423 Mon Sep 17 00:00:00 2001 From: Cosmin Ratiu Date: Tue, 9 Apr 2024 22:08:12 +0300 Subject: [PATCH 010/107] net/mlx5: Properly link new fs rules into the tree [ Upstream commit 7c6782ad4911cbee874e85630226ed389ff2e453 ] Previously, add_rule_fg would only add newly created rules from the handle into the tree when they had a refcount of 1. On the other hand, create_flow_handle tries hard to find and reference already existing identical rules instead of creating new ones. These two behaviors can result in a situation where create_flow_handle 1) creates a new rule and references it, then 2) in a subsequent step during the same handle creation references it again, resulting in a rule with a refcount of 2 that is not linked into the tree, will have a NULL parent and root and will result in a crash when the flow group is deleted because del_sw_hw_rule, invoked on rule deletion, assumes node->parent is != NULL. This happened in the wild, due to another bug related to incorrect handling of duplicate pkt_reformat ids, which lead to the code in create_flow_handle incorrectly referencing a just-added rule in the same flow handle, resulting in the problem described above. Full details are at [1]. This patch changes add_rule_fg to add new rules without parents into the tree, properly initializing them and avoiding the crash. This makes it more consistent with how rules are added to an FTE in create_flow_handle. Fixes: 74491de93712 ("net/mlx5: Add multi dest support") Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1] Signed-off-by: Cosmin Ratiu Reviewed-by: Tariq Toukan Reviewed-by: Mark Bloch Signed-off-by: Saeed Mahameed Signed-off-by: Tariq Toukan Link: https://lore.kernel.org/r/20240409190820.227554-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c b/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c index 41087c0618c1..93fcde150a42 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c @@ -1549,8 +1549,9 @@ static struct mlx5_flow_handle *add_rule_fg(struct mlx5_flow_group *fg, } trace_mlx5_fs_set_fte(fte, false); + /* Link newly added rules into the tree. */ for (i = 0; i < handle->num_rules; i++) { - if (refcount_read(&handle->rule[i]->node.refcount) == 1) { + if (!handle->rule[i]->node.parent) { tree_add_node(&handle->rule[i]->node, &fte->node); trace_mlx5_fs_add_rule(handle->rule[i]); } From 7f4c391d3b549248118c5227679f6745098c2726 Mon Sep 17 00:00:00 2001 From: Kuniyuki Iwashima Date: Tue, 23 Jan 2024 09:08:53 -0800 Subject: [PATCH 011/107] af_unix: Do not use atomic ops for unix_sk(sk)->inflight. [ Upstream commit 97af84a6bba2ab2b9c704c08e67de3b5ea551bb2 ] When touching unix_sk(sk)->inflight, we are always under spin_lock(&unix_gc_lock). Let's convert unix_sk(sk)->inflight to the normal unsigned long. Signed-off-by: Kuniyuki Iwashima Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/20240123170856.41348-3-kuniyu@amazon.com Signed-off-by: Jakub Kicinski Stable-dep-of: 47d8ac011fe1 ("af_unix: Fix garbage collector racing against connect()") Signed-off-by: Sasha Levin --- include/net/af_unix.h | 2 +- net/unix/af_unix.c | 4 ++-- net/unix/garbage.c | 17 ++++++++--------- net/unix/scm.c | 8 +++++--- 4 files changed, 16 insertions(+), 15 deletions(-) diff --git a/include/net/af_unix.h b/include/net/af_unix.h index 6cb5026cf727..e7612295b262 100644 --- a/include/net/af_unix.h +++ b/include/net/af_unix.h @@ -52,7 +52,7 @@ struct unix_sock { struct mutex iolock, bindlock; struct sock *peer; struct list_head link; - atomic_long_t inflight; + unsigned long inflight; spinlock_t lock; unsigned long gc_flags; #define UNIX_GC_CANDIDATE 0 diff --git a/net/unix/af_unix.c b/net/unix/af_unix.c index 9b1dd845bca1..53335989a6f0 100644 --- a/net/unix/af_unix.c +++ b/net/unix/af_unix.c @@ -809,11 +809,11 @@ static struct sock *unix_create1(struct net *net, struct socket *sock, int kern) sk->sk_write_space = unix_write_space; sk->sk_max_ack_backlog = net->unx.sysctl_max_dgram_qlen; sk->sk_destruct = unix_sock_destructor; - u = unix_sk(sk); + u = unix_sk(sk); + u->inflight = 0; u->path.dentry = NULL; u->path.mnt = NULL; spin_lock_init(&u->lock); - atomic_long_set(&u->inflight, 0); INIT_LIST_HEAD(&u->link); mutex_init(&u->iolock); /* single task reading lock */ mutex_init(&u->bindlock); /* single task binding lock */ diff --git a/net/unix/garbage.c b/net/unix/garbage.c index 9121a4d5436d..675fbe594dbb 100644 --- a/net/unix/garbage.c +++ b/net/unix/garbage.c @@ -166,17 +166,18 @@ static void scan_children(struct sock *x, void (*func)(struct unix_sock *), static void dec_inflight(struct unix_sock *usk) { - atomic_long_dec(&usk->inflight); + usk->inflight--; } static void inc_inflight(struct unix_sock *usk) { - atomic_long_inc(&usk->inflight); + usk->inflight++; } static void inc_inflight_move_tail(struct unix_sock *u) { - atomic_long_inc(&u->inflight); + u->inflight++; + /* If this still might be part of a cycle, move it to the end * of the list, so that it's checked even if it was already * passed over @@ -237,14 +238,12 @@ void unix_gc(void) */ list_for_each_entry_safe(u, next, &gc_inflight_list, link) { long total_refs; - long inflight_refs; total_refs = file_count(u->sk.sk_socket->file); - inflight_refs = atomic_long_read(&u->inflight); - BUG_ON(inflight_refs < 1); - BUG_ON(total_refs < inflight_refs); - if (total_refs == inflight_refs) { + BUG_ON(!u->inflight); + BUG_ON(total_refs < u->inflight); + if (total_refs == u->inflight) { list_move_tail(&u->link, &gc_candidates); __set_bit(UNIX_GC_CANDIDATE, &u->gc_flags); __set_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags); @@ -271,7 +270,7 @@ void unix_gc(void) /* Move cursor to after the current position. */ list_move(&cursor, &u->link); - if (atomic_long_read(&u->inflight) > 0) { + if (u->inflight) { list_move_tail(&u->link, ¬_cycle_list); __clear_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags); scan_children(&u->sk, inc_inflight_move_tail, NULL); diff --git a/net/unix/scm.c b/net/unix/scm.c index 51b623de3be5..785e8c4669e2 100644 --- a/net/unix/scm.c +++ b/net/unix/scm.c @@ -51,12 +51,13 @@ void unix_inflight(struct user_struct *user, struct file *fp) if (s) { struct unix_sock *u = unix_sk(s); - if (atomic_long_inc_return(&u->inflight) == 1) { + if (!u->inflight) { BUG_ON(!list_empty(&u->link)); list_add_tail(&u->link, &gc_inflight_list); } else { BUG_ON(list_empty(&u->link)); } + u->inflight++; /* Paired with READ_ONCE() in wait_for_unix_gc() */ WRITE_ONCE(unix_tot_inflight, unix_tot_inflight + 1); } @@ -73,10 +74,11 @@ void unix_notinflight(struct user_struct *user, struct file *fp) if (s) { struct unix_sock *u = unix_sk(s); - BUG_ON(!atomic_long_read(&u->inflight)); + BUG_ON(!u->inflight); BUG_ON(list_empty(&u->link)); - if (atomic_long_dec_and_test(&u->inflight)) + u->inflight--; + if (!u->inflight) list_del_init(&u->link); /* Paired with READ_ONCE() in wait_for_unix_gc() */ WRITE_ONCE(unix_tot_inflight, unix_tot_inflight - 1); From 343c5372d5e17b306db5f8f3c895539b06e3177f Mon Sep 17 00:00:00 2001 From: Michal Luczaj Date: Tue, 9 Apr 2024 22:09:39 +0200 Subject: [PATCH 012/107] af_unix: Fix garbage collector racing against connect() [ Upstream commit 47d8ac011fe1c9251070e1bd64cb10b48193ec51 ] Garbage collector does not take into account the risk of embryo getting enqueued during the garbage collection. If such embryo has a peer that carries SCM_RIGHTS, two consecutive passes of scan_children() may see a different set of children. Leading to an incorrectly elevated inflight count, and then a dangling pointer within the gc_inflight_list. sockets are AF_UNIX/SOCK_STREAM S is an unconnected socket L is a listening in-flight socket bound to addr, not in fdtable V's fd will be passed via sendmsg(), gets inflight count bumped connect(S, addr) sendmsg(S, [V]); close(V) __unix_gc() ---------------- ------------------------- ----------- NS = unix_create1() skb1 = sock_wmalloc(NS) L = unix_find_other(addr) unix_state_lock(L) unix_peer(S) = NS // V count=1 inflight=0 NS = unix_peer(S) skb2 = sock_alloc() skb_queue_tail(NS, skb2[V]) // V became in-flight // V count=2 inflight=1 close(V) // V count=1 inflight=1 // GC candidate condition met for u in gc_inflight_list: if (total_refs == inflight_refs) add u to gc_candidates // gc_candidates={L, V} for u in gc_candidates: scan_children(u, dec_inflight) // embryo (skb1) was not // reachable from L yet, so V's // inflight remains unchanged __skb_queue_tail(L, skb1) unix_state_unlock(L) for u in gc_candidates: if (u.inflight) scan_children(u, inc_inflight_move_tail) // V count=1 inflight=2 (!) If there is a GC-candidate listening socket, lock/unlock its state. This makes GC wait until the end of any ongoing connect() to that socket. After flipping the lock, a possibly SCM-laden embryo is already enqueued. And if there is another embryo coming, it can not possibly carry SCM_RIGHTS. At this point, unix_inflight() can not happen because unix_gc_lock is already taken. Inflight graph remains unaffected. Fixes: 1fd05ba5a2f2 ("[AF_UNIX]: Rewrite garbage collector, fixes race.") Signed-off-by: Michal Luczaj Reviewed-by: Kuniyuki Iwashima Link: https://lore.kernel.org/r/20240409201047.1032217-1-mhal@rbox.co Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin --- net/unix/garbage.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) diff --git a/net/unix/garbage.c b/net/unix/garbage.c index 675fbe594dbb..58525311e903 100644 --- a/net/unix/garbage.c +++ b/net/unix/garbage.c @@ -235,11 +235,22 @@ void unix_gc(void) * receive queues. Other, non candidate sockets _can_ be * added to queue, so we must make sure only to touch * candidates. + * + * Embryos, though never candidates themselves, affect which + * candidates are reachable by the garbage collector. Before + * being added to a listener's queue, an embryo may already + * receive data carrying SCM_RIGHTS, potentially making the + * passed socket a candidate that is not yet reachable by the + * collector. It becomes reachable once the embryo is + * enqueued. Therefore, we must ensure that no SCM-laden + * embryo appears in a (candidate) listener's queue between + * consecutive scan_children() calls. */ list_for_each_entry_safe(u, next, &gc_inflight_list, link) { + struct sock *sk = &u->sk; long total_refs; - total_refs = file_count(u->sk.sk_socket->file); + total_refs = file_count(sk->sk_socket->file); BUG_ON(!u->inflight); BUG_ON(total_refs < u->inflight); @@ -247,6 +258,11 @@ void unix_gc(void) list_move_tail(&u->link, &gc_candidates); __set_bit(UNIX_GC_CANDIDATE, &u->gc_flags); __set_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags); + + if (sk->sk_state == TCP_LISTEN) { + unix_state_lock(sk); + unix_state_unlock(sk); + } } } From 1cb6c82d11d22be5c1856d909a50df22a247f340 Mon Sep 17 00:00:00 2001 From: David Arinzon Date: Wed, 10 Apr 2024 09:13:55 +0000 Subject: [PATCH 013/107] net: ena: Fix potential sign extension issue [ Upstream commit 713a85195aad25d8a26786a37b674e3e5ec09e3c ] Small unsigned types are promoted to larger signed types in the case of multiplication, the result of which may overflow. In case the result of such a multiplication has its MSB turned on, it will be sign extended with '1's. This changes the multiplication result. Code example of the phenomenon: ------------------------------- u16 x, y; size_t z1, z2; x = y = 0xffff; printk("x=%x y=%x\n",x,y); z1 = x*y; z2 = (size_t)x*y; printk("z1=%lx z2=%lx\n", z1, z2); Output: ------- x=ffff y=ffff z1=fffffffffffe0001 z2=fffe0001 The expected result of ffff*ffff is fffe0001, and without the explicit casting to avoid the unwanted sign extension we got fffffffffffe0001. This commit adds an explicit casting to avoid the sign extension issue. Fixes: 689b2bdaaa14 ("net: ena: add functions for handling Low Latency Queues in ena_com") Signed-off-by: Arthur Kiyanovski Signed-off-by: David Arinzon Reviewed-by: Shannon Nelson Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin --- drivers/net/ethernet/amazon/ena/ena_com.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/amazon/ena/ena_com.c b/drivers/net/ethernet/amazon/ena/ena_com.c index 29700fee42e9..46a796576f6b 100644 --- a/drivers/net/ethernet/amazon/ena/ena_com.c +++ b/drivers/net/ethernet/amazon/ena/ena_com.c @@ -374,7 +374,7 @@ static int ena_com_init_io_sq(struct ena_com_dev *ena_dev, ENA_COM_BOUNCE_BUFFER_CNTRL_CNT; io_sq->bounce_buf_ctrl.next_to_use = 0; - size = io_sq->bounce_buf_ctrl.buffer_size * + size = (size_t)io_sq->bounce_buf_ctrl.buffer_size * io_sq->bounce_buf_ctrl.buffers_num; dev_node = dev_to_node(ena_dev->dmadev); From 70040ce92ea73f929cf72dddd8443e567eb45a76 Mon Sep 17 00:00:00 2001 From: Boris Burkov Date: Tue, 19 Mar 2024 10:54:22 -0700 Subject: [PATCH 014/107] btrfs: qgroup: correctly model root qgroup rsv in convert commit 141fb8cd206ace23c02cd2791c6da52c1d77d42a upstream. We use add_root_meta_rsv and sub_root_meta_rsv to track prealloc and pertrans reservations for subvolumes when quotas are enabled. The convert function does not properly increment pertrans after decrementing prealloc, so the count is not accurate. Note: we check that the fs is not read-only to mirror the logic in qgroup_convert_meta, which checks that before adding to the pertrans rsv. Fixes: 8287475a2055 ("btrfs: qgroup: Use root::qgroup_meta_rsv_* to record qgroup meta reserved space") CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Qu Wenruo Signed-off-by: Boris Burkov Signed-off-by: David Sterba Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/qgroup.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/btrfs/qgroup.c b/fs/btrfs/qgroup.c index 42412a4554d3..d6184b6206ff 100644 --- a/fs/btrfs/qgroup.c +++ b/fs/btrfs/qgroup.c @@ -4061,6 +4061,8 @@ void btrfs_qgroup_convert_reserved_meta(struct btrfs_root *root, int num_bytes) BTRFS_QGROUP_RSV_META_PREALLOC); trace_qgroup_meta_convert(root, num_bytes); qgroup_convert_meta(fs_info, root->root_key.objectid, num_bytes); + if (!sb_rdonly(fs_info->sb)) + add_root_meta_rsv(root, num_bytes, BTRFS_QGROUP_RSV_META_PERTRANS); } /* From 5a2f957e3c4553bbb100504a1acfeaeb33f4ca4e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= Date: Thu, 4 Apr 2024 23:33:25 +0300 Subject: [PATCH 015/107] drm/client: Fully protect modes[] with dev->mode_config.mutex MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 3eadd887dbac1df8f25f701e5d404d1b90fd0fea upstream. The modes[] array contains pointers to modes on the connectors' mode lists, which are protected by dev->mode_config.mutex. Thus we need to extend modes[] the same protection or by the time we use it the elements may already be pointing to freed/reused memory. Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10583 Signed-off-by: Ville Syrjälä Link: https://patchwork.freedesktop.org/patch/msgid/20240404203336.10454-2-ville.syrjala@linux.intel.com Reviewed-by: Dmitry Baryshkov Reviewed-by: Jani Nikula Reviewed-by: Thomas Zimmermann Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/drm_client_modeset.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/drm_client_modeset.c b/drivers/gpu/drm/drm_client_modeset.c index 10769efaf7cb..827622d18fa8 100644 --- a/drivers/gpu/drm/drm_client_modeset.c +++ b/drivers/gpu/drm/drm_client_modeset.c @@ -700,6 +700,7 @@ int drm_client_modeset_probe(struct drm_client_dev *client, unsigned int width, unsigned int total_modes_count = 0; struct drm_client_offset *offsets; unsigned int connector_count = 0; + /* points to modes protected by mode_config.mutex */ struct drm_display_mode **modes; struct drm_crtc **crtcs; int i, ret = 0; @@ -768,7 +769,6 @@ int drm_client_modeset_probe(struct drm_client_dev *client, unsigned int width, drm_client_pick_crtcs(client, connectors, connector_count, crtcs, modes, 0, width, height); } - mutex_unlock(&dev->mode_config.mutex); drm_client_modeset_release(client); @@ -798,6 +798,7 @@ int drm_client_modeset_probe(struct drm_client_dev *client, unsigned int width, modeset->y = offset->y; } } + mutex_unlock(&dev->mode_config.mutex); mutex_unlock(&client->modeset_mutex); out: From 5fd4f8142199f91a51745d0a259b4f2d6b0f98ea Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Thu, 28 Mar 2024 10:21:47 +1000 Subject: [PATCH 016/107] vhost: Add smp_rmb() in vhost_vq_avail_empty() commit 22e1992cf7b034db5325660e98c41ca5afa5f519 upstream. A smp_rmb() has been missed in vhost_vq_avail_empty(), spotted by Will. Otherwise, it's not ensured the available ring entries pushed by guest can be observed by vhost in time, leading to stale available ring entries fetched by vhost in vhost_get_vq_desc(), as reported by Yihuang Yu on NVidia's grace-hopper (ARM64) platform. /home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \ -accel kvm -machine virt,gic-version=host -cpu host \ -smp maxcpus=1,cpus=1,sockets=1,clusters=1,cores=1,threads=1 \ -m 4096M,slots=16,maxmem=64G \ -object memory-backend-ram,id=mem0,size=4096M \ : \ -netdev tap,id=vnet0,vhost=true \ -device virtio-net-pci,bus=pcie.8,netdev=vnet0,mac=52:54:00:f1:26:b0 : guest# netperf -H 10.26.1.81 -l 60 -C -c -t UDP_STREAM virtio_net virtio0: output.0:id 100 is not a head! Add the missed smp_rmb() in vhost_vq_avail_empty(). When tx_can_batch() returns true, it means there's still pending tx buffers. Since it might read indices, so it still can bypass the smp_rmb() in vhost_get_vq_desc(). Note that it should be safe until vq->avail_idx is changed by commit 275bf960ac697 ("vhost: better detection of available buffers"). Fixes: 275bf960ac69 ("vhost: better detection of available buffers") Cc: # v4.11+ Reported-by: Yihuang Yu Suggested-by: Will Deacon Signed-off-by: Gavin Shan Acked-by: Jason Wang Message-Id: <20240328002149.1141302-2-gshan@redhat.com> Signed-off-by: Michael S. Tsirkin Reviewed-by: Stefano Garzarella Signed-off-by: Greg Kroah-Hartman --- drivers/vhost/vhost.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/drivers/vhost/vhost.c b/drivers/vhost/vhost.c index b2e92927e8a1..484818796978 100644 --- a/drivers/vhost/vhost.c +++ b/drivers/vhost/vhost.c @@ -2519,9 +2519,19 @@ bool vhost_vq_avail_empty(struct vhost_dev *dev, struct vhost_virtqueue *vq) r = vhost_get_avail_idx(vq, &avail_idx); if (unlikely(r)) return false; - vq->avail_idx = vhost16_to_cpu(vq, avail_idx); - return vq->avail_idx == vq->last_avail_idx; + vq->avail_idx = vhost16_to_cpu(vq, avail_idx); + if (vq->avail_idx != vq->last_avail_idx) { + /* Since we have updated avail_idx, the following + * call to vhost_get_vq_desc() will read available + * ring entries. Make sure that read happens after + * the avail_idx read. + */ + smp_rmb(); + return false; + } + + return true; } EXPORT_SYMBOL_GPL(vhost_vq_avail_empty); From ed180e21c2bf89cb793f606f7ebd327708e13ae8 Mon Sep 17 00:00:00 2001 From: John Stultz Date: Wed, 10 Apr 2024 16:26:30 -0700 Subject: [PATCH 017/107] selftests: timers: Fix abs() warning in posix_timers test commit ed366de8ec89d4f960d66c85fc37d9de22f7bf6d upstream. Building with clang results in the following warning: posix_timers.c:69:6: warning: absolute value function 'abs' given an argument of type 'long long' but has parameter of type 'int' which may cause truncation of value [-Wabsolute-value] if (abs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) { ^ So switch to using llabs() instead. Fixes: 0bc4b0cf1570 ("selftests: add basic posix timers selftests") Signed-off-by: John Stultz Signed-off-by: Thomas Gleixner Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240410232637.4135564-3-jstultz@google.com Signed-off-by: Greg Kroah-Hartman --- tools/testing/selftests/timers/posix_timers.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/testing/selftests/timers/posix_timers.c b/tools/testing/selftests/timers/posix_timers.c index 0ba500056e63..193a984f512c 100644 --- a/tools/testing/selftests/timers/posix_timers.c +++ b/tools/testing/selftests/timers/posix_timers.c @@ -66,7 +66,7 @@ static int check_diff(struct timeval start, struct timeval end) diff = end.tv_usec - start.tv_usec; diff += (end.tv_sec - start.tv_sec) * USECS_PER_SEC; - if (abs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) { + if (llabs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) { printf("Diff too high: %lld..", diff); return -1; } From b282473af70021e0c672fb5f3fb01a46f699533c Mon Sep 17 00:00:00 2001 From: Adam Dunlap Date: Mon, 18 Mar 2024 16:09:27 -0700 Subject: [PATCH 018/107] x86/apic: Force native_apic_mem_read() to use the MOV instruction commit 5ce344beaca688f4cdea07045e0b8f03dc537e74 upstream. When done from a virtual machine, instructions that touch APIC memory must be emulated. By convention, MMIO accesses are typically performed via io.h helpers such as readl() or writeq() to simplify instruction emulation/decoding (ex: in KVM hosts and SEV guests) [0]. Currently, native_apic_mem_read() does not follow this convention, allowing the compiler to emit instructions other than the MOV instruction generated by readl(). In particular, when the kernel is compiled with clang and run as a SEV-ES or SEV-SNP guest, the compiler would emit a TESTL instruction which is not supported by the SEV-ES emulator, causing a boot failure in that environment. It is likely the same problem would happen in a TDX guest as that uses the same instruction emulator as SEV-ES. To make sure all emulators can emulate APIC memory reads via MOV, use the readl() function in native_apic_mem_read(). It is expected that any emulator would support MOV in any addressing mode as it is the most generic and is what is usually emitted currently. The TESTL instruction is emitted when native_apic_mem_read() is inlined into apic_mem_wait_icr_idle(). The emulator comes from insn_decode_mmio() in arch/x86/lib/insn-eval.c. It's not worth it to extend insn_decode_mmio() to support more instructions since, in theory, the compiler could choose to output nearly any instruction for such reads which would bloat the emulator beyond reason. [0] https://lore.kernel.org/all/20220405232939.73860-12-kirill.shutemov@linux.intel.com/ [ bp: Massage commit message, fix typos. ] Signed-off-by: Adam Dunlap Signed-off-by: Borislav Petkov (AMD) Reviewed-by: Thomas Gleixner Reviewed-by: Ard Biesheuvel Tested-by: Kevin Loughlin Cc: Link: https://lore.kernel.org/r/20240318230927.2191933-1-acdunlap@google.com Signed-off-by: Greg Kroah-Hartman --- arch/x86/include/asm/apic.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h index a49b1aeb2147..36d6273b079a 100644 --- a/arch/x86/include/asm/apic.h +++ b/arch/x86/include/asm/apic.h @@ -12,6 +12,7 @@ #include #include #include +#include #define ARCH_APICTIMER_STOPS_ON_C3 1 @@ -111,7 +112,7 @@ static inline void native_apic_mem_write(u32 reg, u32 v) static inline u32 native_apic_mem_read(u32 reg) { - return *((volatile u32 *)(APIC_BASE + reg)); + return readl((void __iomem *)(APIC_BASE + reg)); } extern void native_apic_wait_icr_idle(void); From 14b74fc24c65d8c47e9adaa5fba3092016912425 Mon Sep 17 00:00:00 2001 From: Boris Burkov Date: Thu, 21 Mar 2024 10:14:24 -0700 Subject: [PATCH 019/107] btrfs: record delayed inode root in transaction [ Upstream commit 71537e35c324ea6fbd68377a4f26bb93a831ae35 ] When running delayed inode updates, we do not record the inode's root in the transaction, but we do allocate PREALLOC and thus converted PERTRANS space for it. To be sure we free that PERTRANS meta rsv, we must ensure that we record the root in the transaction. Fixes: 4f5427ccce5d ("btrfs: delayed-inode: Use new qgroup meta rsv for delayed inode and item") CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Qu Wenruo Signed-off-by: Boris Burkov Signed-off-by: David Sterba Signed-off-by: Sasha Levin --- fs/btrfs/delayed-inode.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/fs/btrfs/delayed-inode.c b/fs/btrfs/delayed-inode.c index eacc020b1419..95afe5ef7500 100644 --- a/fs/btrfs/delayed-inode.c +++ b/fs/btrfs/delayed-inode.c @@ -1137,6 +1137,9 @@ __btrfs_commit_inode_delayed_items(struct btrfs_trans_handle *trans, if (ret) return ret; + ret = btrfs_record_root_in_trans(trans, node->root); + if (ret) + return ret; ret = btrfs_update_delayed_inode(trans, node->root, path, node); return ret; } From 49cacd34e35d721e4b4f3e754e9091decc4b6232 Mon Sep 17 00:00:00 2001 From: Yuanhe Shu Date: Mon, 26 Feb 2024 11:18:16 +0800 Subject: [PATCH 020/107] selftests/ftrace: Limit length in subsystem-enable tests commit 1a4ea83a6e67f1415a1f17c1af5e9c814c882bb5 upstream. While sched* events being traced and sched* events continuously happen, "[xx] event tracing - enable/disable with subsystem level files" would not stop as on some slower systems it seems to take forever. Select the first 100 lines of output would be enough to judge whether there are more than 3 types of sched events. Fixes: 815b18ea66d6 ("ftracetest: Add basic event tracing test cases") Cc: stable@vger.kernel.org Signed-off-by: Yuanhe Shu Acked-by: Masami Hiramatsu (Google) Acked-by: Steven Rostedt (Google) Signed-off-by: Shuah Khan Signed-off-by: Greg Kroah-Hartman --- .../selftests/ftrace/test.d/event/subsystem-enable.tc | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc b/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc index 83a8c571e93a..ff6cf579f503 100644 --- a/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc +++ b/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc @@ -22,7 +22,7 @@ echo 'sched:*' > set_event yield -count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` +count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` if [ $count -lt 3 ]; then fail "at least fork, exec and exit events should be recorded" fi @@ -33,7 +33,7 @@ echo 1 > events/sched/enable yield -count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` +count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` if [ $count -lt 3 ]; then fail "at least fork, exec and exit events should be recorded" fi @@ -44,7 +44,7 @@ echo 0 > events/sched/enable yield -count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` +count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l` if [ $count -ne 0 ]; then fail "any of scheduler events should not be recorded" fi From 93eb31e7c3399e326259f2caa17be1e821f5a412 Mon Sep 17 00:00:00 2001 From: Zheng Yejian Date: Wed, 10 Apr 2024 09:58:02 +0800 Subject: [PATCH 021/107] kprobes: Fix possible use-after-free issue on kprobe registration commit 325f3fb551f8cd672dbbfc4cf58b14f9ee3fc9e8 upstream. When unloading a module, its state is changing MODULE_STATE_LIVE -> MODULE_STATE_GOING -> MODULE_STATE_UNFORMED. Each change will take a time. `is_module_text_address()` and `__module_text_address()` works with MODULE_STATE_LIVE and MODULE_STATE_GOING. If we use `is_module_text_address()` and `__module_text_address()` separately, there is a chance that the first one is succeeded but the next one is failed because module->state becomes MODULE_STATE_UNFORMED between those operations. In `check_kprobe_address_safe()`, if the second `__module_text_address()` is failed, that is ignored because it expected a kernel_text address. But it may have failed simply because module->state has been changed to MODULE_STATE_UNFORMED. In this case, arm_kprobe() will try to modify non-exist module text address (use-after-free). To fix this problem, we should not use separated `is_module_text_address()` and `__module_text_address()`, but use only `__module_text_address()` once and do `try_module_get(module)` which is only available with MODULE_STATE_LIVE. Link: https://lore.kernel.org/all/20240410015802.265220-1-zhengyejian1@huawei.com/ Fixes: 28f6c37a2910 ("kprobes: Forbid probing on trampoline and BPF code areas") Cc: stable@vger.kernel.org Signed-off-by: Zheng Yejian Signed-off-by: Masami Hiramatsu (Google) [Fix conflict due to lack dependency commit 223a76b268c9 ("kprobes: Fix coding style issues")] Signed-off-by: Zheng Yejian Signed-off-by: Greg Kroah-Hartman --- kernel/kprobes.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) diff --git a/kernel/kprobes.c b/kernel/kprobes.c index aecf4342f67c..063e4ade1680 100644 --- a/kernel/kprobes.c +++ b/kernel/kprobes.c @@ -1593,10 +1593,17 @@ static int check_kprobe_address_safe(struct kprobe *p, jump_label_lock(); preempt_disable(); - /* Ensure it is not in reserved area nor out of text */ - if (!(core_kernel_text((unsigned long) p->addr) || - is_module_text_address((unsigned long) p->addr)) || - in_gate_area_no_mm((unsigned long) p->addr) || + /* Ensure the address is in a text area, and find a module if exists. */ + *probed_mod = NULL; + if (!core_kernel_text((unsigned long) p->addr)) { + *probed_mod = __module_text_address((unsigned long) p->addr); + if (!(*probed_mod)) { + ret = -EINVAL; + goto out; + } + } + /* Ensure it is not in reserved area. */ + if (in_gate_area_no_mm((unsigned long) p->addr) || within_kprobe_blacklist((unsigned long) p->addr) || jump_label_text_reserved(p->addr, p->addr) || find_bug((unsigned long)p->addr)) { @@ -1604,8 +1611,7 @@ static int check_kprobe_address_safe(struct kprobe *p, goto out; } - /* Check if are we probing a module */ - *probed_mod = __module_text_address((unsigned long) p->addr); + /* Get module refcount and reject __init functions for loaded modules. */ if (*probed_mod) { /* * We must hold a refcount of the probed module while updating From 2450a69d2ee75d1f0112d509ac82ef98f5ad6b5f Mon Sep 17 00:00:00 2001 From: Siddh Raman Pant Date: Thu, 18 Apr 2024 18:58:06 +0530 Subject: [PATCH 022/107] Revert "tracing/trigger: Fix to return error if failed to alloc snapshot" This reverts commit 8ffd5590f4d6ef5460acbeac7fbdff7025f9b419 which is commit 0958b33ef5a04ed91f61cef4760ac412080c4e08 upstream. The change has an incorrect assumption about the return value because in the current stable trees for versions 5.15 and before, the following commit responsible for making 0 a success value is not present: b8cc44a4d3c1 ("tracing: Remove logic for registering multiple event triggers at a time") The return value should be 0 on failure in the current tree, because in the functions event_trigger_callback() and event_enable_trigger_func(), we have: ret = cmd_ops->reg(glob, trigger_ops, trigger_data, file); /* * The above returns on success the # of functions enabled, * but if it didn't find any functions it returns zero. * Consider no functions a failure too. */ if (!ret) { ret = -ENOENT; Cc: stable@kernel.org # 5.15, 5.10, 5.4, 4.19 Signed-off-by: Siddh Raman Pant Signed-off-by: Greg Kroah-Hartman --- kernel/trace/trace_events_trigger.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/kernel/trace/trace_events_trigger.c b/kernel/trace/trace_events_trigger.c index 634d120eab2b..82580f7ffad9 100644 --- a/kernel/trace/trace_events_trigger.c +++ b/kernel/trace/trace_events_trigger.c @@ -1140,10 +1140,8 @@ register_snapshot_trigger(char *glob, struct event_trigger_ops *ops, struct event_trigger_data *data, struct trace_event_file *file) { - int ret = tracing_alloc_snapshot_instance(file->tr); - - if (ret < 0) - return ret; + if (tracing_alloc_snapshot_instance(file->tr) != 0) + return 0; return register_trigger(glob, ops, data, file); } From b38a133d37fa421c8447b383d788c9cc6f5cb34c Mon Sep 17 00:00:00 2001 From: Ziyang Xuan Date: Sun, 7 Apr 2024 14:56:04 +0800 Subject: [PATCH 023/107] netfilter: nf_tables: Fix potential data-race in __nft_expr_type_get() [ Upstream commit f969eb84ce482331a991079ab7a5c4dc3b7f89bf ] nft_unregister_expr() can concurrent with __nft_expr_type_get(), and there is not any protection when iterate over nf_tables_expressions list in __nft_expr_type_get(). Therefore, there is potential data-race of nf_tables_expressions list entry. Use list_for_each_entry_rcu() to iterate over nf_tables_expressions list in __nft_expr_type_get(), and use rcu_read_lock() in the caller nft_expr_type_get() to protect the entire type query process. Fixes: ef1f7df9170d ("netfilter: nf_tables: expression ops overloading") Signed-off-by: Ziyang Xuan Signed-off-by: Pablo Neira Ayuso Signed-off-by: Sasha Levin --- net/netfilter/nf_tables_api.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/net/netfilter/nf_tables_api.c b/net/netfilter/nf_tables_api.c index b4bb93b9aafc..8131d858f38d 100644 --- a/net/netfilter/nf_tables_api.c +++ b/net/netfilter/nf_tables_api.c @@ -2239,7 +2239,7 @@ static const struct nft_expr_type *__nft_expr_type_get(u8 family, { const struct nft_expr_type *type, *candidate = NULL; - list_for_each_entry(type, &nf_tables_expressions, list) { + list_for_each_entry_rcu(type, &nf_tables_expressions, list) { if (!nla_strcmp(nla, type->name)) { if (!type->family && !candidate) candidate = type; @@ -2271,9 +2271,13 @@ static const struct nft_expr_type *nft_expr_type_get(struct net *net, if (nla == NULL) return ERR_PTR(-EINVAL); + rcu_read_lock(); type = __nft_expr_type_get(family, nla); - if (type != NULL && try_module_get(type->owner)) + if (type != NULL && try_module_get(type->owner)) { + rcu_read_unlock(); return type; + } + rcu_read_unlock(); lockdep_nfnl_nft_mutex_not_held(); #ifdef CONFIG_MODULES From 4b0dcae5c4797bf31c63011ed62917210d3fdac3 Mon Sep 17 00:00:00 2001 From: Lei Chen Date: Sun, 14 Apr 2024 22:02:46 -0400 Subject: [PATCH 024/107] tun: limit printing rate when illegal packet received by tun dev [ Upstream commit f8bbc07ac535593139c875ffa19af924b1084540 ] vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a59542 ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen Reviewed-by: Willem de Bruijn Acked-by: Jason Wang Reviewed-by: Eric Dumazet Acked-by: Michael S. Tsirkin Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/tun.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) diff --git a/drivers/net/tun.c b/drivers/net/tun.c index 47958e6bd77f..3c52d0d24704 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -2208,14 +2208,16 @@ static ssize_t tun_put_user(struct tun_struct *tun, tun_is_little_endian(tun), true, vlan_hlen)) { struct skb_shared_info *sinfo = skb_shinfo(skb); - pr_err("unexpected GSO type: " - "0x%x, gso_size %d, hdr_len %d\n", - sinfo->gso_type, tun16_to_cpu(tun, gso.gso_size), - tun16_to_cpu(tun, gso.hdr_len)); - print_hex_dump(KERN_ERR, "tun: ", - DUMP_PREFIX_NONE, - 16, 1, skb->head, - min((int)tun16_to_cpu(tun, gso.hdr_len), 64), true); + + if (net_ratelimit()) { + netdev_err(tun->dev, "unexpected GSO type: 0x%x, gso_size %d, hdr_len %d\n", + sinfo->gso_type, tun16_to_cpu(tun, gso.gso_size), + tun16_to_cpu(tun, gso.hdr_len)); + print_hex_dump(KERN_ERR, "tun: ", + DUMP_PREFIX_NONE, + 16, 1, skb->head, + min((int)tun16_to_cpu(tun, gso.hdr_len), 64), true); + } WARN_ON_ONCE(1); return -EINVAL; } From 80997511b9c8e147e7b0d05f90056cd59b8ae94a Mon Sep 17 00:00:00 2001 From: "Yanjun.Zhu" Date: Thu, 14 Mar 2024 07:51:40 +0100 Subject: [PATCH 025/107] RDMA/rxe: Fix the problem "mutex_destroy missing" [ Upstream commit 481047d7e8391d3842ae59025806531cdad710d9 ] When a mutex lock is not used any more, the function mutex_destroy should be called to mark the mutex lock uninitialized. Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yanjun.Zhu Link: https://lore.kernel.org/r/20240314065140.27468-1-yanjun.zhu@linux.dev Reviewed-by: Daisuke Matsuda Signed-off-by: Leon Romanovsky Signed-off-by: Sasha Levin --- drivers/infiniband/sw/rxe/rxe.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/infiniband/sw/rxe/rxe.c b/drivers/infiniband/sw/rxe/rxe.c index de5f3efe9fcb..76e103ef5be3 100644 --- a/drivers/infiniband/sw/rxe/rxe.c +++ b/drivers/infiniband/sw/rxe/rxe.c @@ -72,6 +72,8 @@ void rxe_dealloc(struct ib_device *ib_dev) if (rxe->tfm) crypto_free_shash(rxe->tfm); + + mutex_destroy(&rxe->usdev_lock); } /* initialize rxe device parameters */ From 4b1930bd425021c3adc17f191415f9de18f844be Mon Sep 17 00:00:00 2001 From: Michael Guralnik Date: Wed, 3 Apr 2024 12:03:46 +0300 Subject: [PATCH 026/107] RDMA/mlx5: Fix port number for counter query in multi-port configuration [ Upstream commit be121ffb384f53e966ee7299ffccc6eeb61bc73d ] Set the correct port when querying PPCNT in multi-port configuration. Distinguish between cases where switchdev mode was enabled to multi-port configuration and don't overwrite the queried port to 1 in multi-port case. Fixes: 74b30b3ad5ce ("RDMA/mlx5: Set local port to one when accessing counters") Signed-off-by: Michael Guralnik Link: https://lore.kernel.org/r/9bfcc8ade958b760a51408c3ad654a01b11f7d76.1712134988.git.leon@kernel.org Signed-off-by: Leon Romanovsky Signed-off-by: Sasha Levin --- drivers/infiniband/hw/mlx5/mad.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/infiniband/hw/mlx5/mad.c b/drivers/infiniband/hw/mlx5/mad.c index 3897a3ce02ad..84d72b3b6df8 100644 --- a/drivers/infiniband/hw/mlx5/mad.c +++ b/drivers/infiniband/hw/mlx5/mad.c @@ -219,7 +219,8 @@ static int process_pma_cmd(struct mlx5_ib_dev *dev, u8 port_num, mdev = dev->mdev; mdev_port_num = 1; } - if (MLX5_CAP_GEN(dev->mdev, num_ports) == 1) { + if (MLX5_CAP_GEN(dev->mdev, num_ports) == 1 && + !mlx5_core_mp_enabled(mdev)) { /* set local port to one for Function-Per-Port HCA. */ mdev = dev->mdev; mdev_port_num = 1; From 5050ae879a828d752b439e3827aac126709da6d1 Mon Sep 17 00:00:00 2001 From: Mikhail Kobuk Date: Thu, 11 Apr 2024 14:08:52 +0300 Subject: [PATCH 027/107] drm: nv04: Fix out of bounds access [ Upstream commit cf92bb778eda7830e79452c6917efa8474a30c1e ] When Output Resource (dcb->or) value is assigned in fabricate_dcb_output(), there may be out of bounds access to dac_users array in case dcb->or is zero because ffs(dcb->or) is used as index there. The 'or' argument of fabricate_dcb_output() must be interpreted as a number of bit to set, not value. Utilize macros from 'enum nouveau_or' in calls instead of hardcoding. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 2e5702aff395 ("drm/nouveau: fabricate DCB encoder table for iMac G4") Fixes: 670820c0e6a9 ("drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.") Signed-off-by: Mikhail Kobuk Signed-off-by: Danilo Krummrich Link: https://patchwork.freedesktop.org/patch/msgid/20240411110854.16701-1-m.kobuk@ispras.ru Signed-off-by: Sasha Levin --- drivers/gpu/drm/nouveau/nouveau_bios.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/nouveau/nouveau_bios.c b/drivers/gpu/drm/nouveau/nouveau_bios.c index d204ea8a5618..5cdf0d8d4bc1 100644 --- a/drivers/gpu/drm/nouveau/nouveau_bios.c +++ b/drivers/gpu/drm/nouveau/nouveau_bios.c @@ -23,6 +23,7 @@ */ #include "nouveau_drv.h" +#include "nouveau_bios.h" #include "nouveau_reg.h" #include "dispnv04/hw.h" #include "nouveau_encoder.h" @@ -1672,7 +1673,7 @@ apply_dcb_encoder_quirks(struct drm_device *dev, int idx, u32 *conn, u32 *conf) */ if (nv_match_device(dev, 0x0201, 0x1462, 0x8851)) { if (*conn == 0xf2005014 && *conf == 0xffffffff) { - fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 1, 1, 1); + fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 1, 1, DCB_OUTPUT_B); return false; } } @@ -1758,26 +1759,26 @@ fabricate_dcb_encoder_table(struct drm_device *dev, struct nvbios *bios) #ifdef __powerpc__ /* Apple iMac G4 NV17 */ if (of_machine_is_compatible("PowerMac4,5")) { - fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 0, all_heads, 1); - fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG, 1, all_heads, 2); + fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 0, all_heads, DCB_OUTPUT_B); + fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG, 1, all_heads, DCB_OUTPUT_C); return; } #endif /* Make up some sane defaults */ fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG, - bios->legacy.i2c_indices.crt, 1, 1); + bios->legacy.i2c_indices.crt, 1, DCB_OUTPUT_B); if (nv04_tv_identify(dev, bios->legacy.i2c_indices.tv) >= 0) fabricate_dcb_output(dcb, DCB_OUTPUT_TV, bios->legacy.i2c_indices.tv, - all_heads, 0); + all_heads, DCB_OUTPUT_A); else if (bios->tmds.output0_script_ptr || bios->tmds.output1_script_ptr) fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, bios->legacy.i2c_indices.panel, - all_heads, 1); + all_heads, DCB_OUTPUT_B); } static int From b9ef935c0a2d4a0a6df2c70de5793cced269fe68 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 25 Mar 2024 11:41:55 -0700 Subject: [PATCH 028/107] clk: Remove prepare_lock hold assertion in __clk_release() [ Upstream commit 8358a76cfb47c9a5af627a0c4e7168aa14fa25f6 ] Removing this assertion lets us move the kref_put() call outside the prepare_lock section. We don't need to hold the prepare_lock here to free memory and destroy the clk_core structure. We've already unlinked the clk from the clk tree and by the time the release function runs nothing holds a reference to the clk_core anymore so anything with the pointer can't access the memory that's being freed anyway. Way back in commit 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of prepare_lock") we didn't need to have this assertion either. Fixes: 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of prepare_lock") Cc: Krzysztof Kozlowski Reviewed-by: Douglas Anderson Signed-off-by: Stephen Boyd Link: https://lore.kernel.org/r/20240325184204.745706-2-sboyd@kernel.org Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index 67051ca60920..85a043e8a9d5 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -3883,8 +3883,6 @@ static void __clk_release(struct kref *ref) { struct clk_core *core = container_of(ref, struct clk_core, ref); - lockdep_assert_held(&prepare_lock); - clk_core_free_parent_map(core); kfree_const(core->name); kfree(core); From fdd3437c7bf04d5b61ae8ebf072b628f2c1c29a5 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Thu, 17 Feb 2022 14:05:53 -0800 Subject: [PATCH 029/107] clk: Mark 'all_lists' as const [ Upstream commit 75061a6ff49ba3482c6319ded0c26e6a526b0967 ] This list array doesn't change at runtime. Mark it const to move to RO memory. Signed-off-by: Stephen Boyd Link: https://lore.kernel.org/r/20220217220554.2711696-2-sboyd@kernel.org Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused") Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index 85a043e8a9d5..f9d89b42b8f9 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -37,7 +37,7 @@ static HLIST_HEAD(clk_root_list); static HLIST_HEAD(clk_orphan_list); static LIST_HEAD(clk_notifier_list); -static struct hlist_head *all_lists[] = { +static const struct hlist_head *all_lists[] = { &clk_root_list, &clk_orphan_list, NULL, @@ -3940,7 +3940,7 @@ static void clk_core_evict_parent_cache_subtree(struct clk_core *root, /* Remove this clk from all parent caches */ static void clk_core_evict_parent_cache(struct clk_core *core) { - struct hlist_head **lists; + const struct hlist_head **lists; struct clk_core *root; lockdep_assert_held(&prepare_lock); From 25ce8c71140316073f3bc75a24f66fd0a1fefc46 Mon Sep 17 00:00:00 2001 From: Claudiu Beznea Date: Thu, 30 Jun 2022 18:12:04 +0300 Subject: [PATCH 030/107] clk: remove extra empty line [ Upstream commit 79806d338829b2bf903480428d8ce5aab8e2d24b ] Remove extra empty line. Signed-off-by: Claudiu Beznea Link: https://lore.kernel.org/r/20220630151205.3935560-1-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused") Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index f9d89b42b8f9..276b8a1f3c3f 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -3508,7 +3508,6 @@ static int __clk_core_init(struct clk_core *core) clk_core_reparent_orphans_nolock(); - kref_init(&core->ref); out: clk_pm_runtime_put(core); From 1d09f800f2a36111e86f0a90a4ea90901e93d148 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Tue, 7 Mar 2023 14:29:28 +0100 Subject: [PATCH 031/107] clk: Print an info line before disabling unused clocks [ Upstream commit 12ca59b91d04df32e41be5a52f0cabba912c11de ] Currently, the regulator framework informs us before calling into their unused cleanup paths, which eases at least some debugging. The same could be beneficial for clocks, so that random shutdowns shortly after most initcalls are done can be less of a guess. Add a pr_info before disabling unused clocks to do so. Reviewed-by: Marijn Suijten Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20230307132928.3887737-1-konrad.dybcio@linaro.org Signed-off-by: Stephen Boyd Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused") Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index 276b8a1f3c3f..7c92dd209a99 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -1315,6 +1315,8 @@ static int clk_disable_unused(void) return 0; } + pr_info("clk: Disabling unused clocks\n"); + clk_prepare_lock(); hlist_for_each_entry(core, &clk_root_list, child_node) From 8cf77c61a84cb8780197ba1551d5953332e9e887 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 25 Mar 2024 11:41:57 -0700 Subject: [PATCH 032/107] clk: Initialize struct clk_core kref earlier [ Upstream commit 9d05ae531c2cff20d5d527f04e28d28e04379929 ] Initialize this kref once we allocate memory for the struct clk_core so that we can reuse the release function to free any memory associated with the structure. This mostly consolidates code, but also clarifies that the kref lifetime exists once the container structure (struct clk_core) is allocated instead of leaving it in a half-baked state for most of __clk_core_init(). Reviewed-by: Douglas Anderson Signed-off-by: Stephen Boyd Link: https://lore.kernel.org/r/20240325184204.745706-4-sboyd@kernel.org Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused") Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 28 +++++++++++++--------------- 1 file changed, 13 insertions(+), 15 deletions(-) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index 7c92dd209a99..f887cea057ee 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -3509,8 +3509,6 @@ static int __clk_core_init(struct clk_core *core) } clk_core_reparent_orphans_nolock(); - - kref_init(&core->ref); out: clk_pm_runtime_put(core); unlock: @@ -3720,6 +3718,16 @@ static void clk_core_free_parent_map(struct clk_core *core) kfree(core->parents); } +/* Free memory allocated for a struct clk_core */ +static void __clk_release(struct kref *ref) +{ + struct clk_core *core = container_of(ref, struct clk_core, ref); + + clk_core_free_parent_map(core); + kfree_const(core->name); + kfree(core); +} + static struct clk * __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw) { @@ -3740,6 +3748,8 @@ __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw) goto fail_out; } + kref_init(&core->ref); + core->name = kstrdup_const(init->name, GFP_KERNEL); if (!core->name) { ret = -ENOMEM; @@ -3794,12 +3804,10 @@ __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw) hw->clk = NULL; fail_create_clk: - clk_core_free_parent_map(core); fail_parents: fail_ops: - kfree_const(core->name); fail_name: - kfree(core); + kref_put(&core->ref, __clk_release); fail_out: return ERR_PTR(ret); } @@ -3879,16 +3887,6 @@ int of_clk_hw_register(struct device_node *node, struct clk_hw *hw) } EXPORT_SYMBOL_GPL(of_clk_hw_register); -/* Free memory allocated for a clock. */ -static void __clk_release(struct kref *ref) -{ - struct clk_core *core = container_of(ref, struct clk_core, ref); - - clk_core_free_parent_map(core); - kfree_const(core->name); - kfree(core); -} - /* * Empty clk_ops for unregistered clocks. These are used temporarily * after clk_unregister() was called on a clock and until last clock From 253ab38d1ee652a596942156978a233970d185ba Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 25 Mar 2024 11:41:58 -0700 Subject: [PATCH 033/107] clk: Get runtime PM before walking tree during disable_unused [ Upstream commit e581cf5d216289ef292d1a4036d53ce90e122469 ] Doug reported [1] the following hung task: INFO: task swapper/0:1 blocked for more than 122 seconds. Not tainted 5.15.149-21875-gf795ebc40eb8 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008 Call trace: __switch_to+0xf4/0x1f4 __schedule+0x418/0xb80 schedule+0x5c/0x10c rpm_resume+0xe0/0x52c rpm_resume+0x178/0x52c __pm_runtime_resume+0x58/0x98 clk_pm_runtime_get+0x30/0xb0 clk_disable_unused_subtree+0x58/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused_subtree+0x38/0x208 clk_disable_unused+0x4c/0xe4 do_one_initcall+0xcc/0x2d8 do_initcall_level+0xa4/0x148 do_initcalls+0x5c/0x9c do_basic_setup+0x24/0x30 kernel_init_freeable+0xec/0x164 kernel_init+0x28/0x120 ret_from_fork+0x10/0x20 INFO: task kworker/u16:0:9 blocked for more than 122 seconds. Not tainted 5.15.149-21875-gf795ebc40eb8 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008 Workqueue: events_unbound deferred_probe_work_func Call trace: __switch_to+0xf4/0x1f4 __schedule+0x418/0xb80 schedule+0x5c/0x10c schedule_preempt_disabled+0x2c/0x48 __mutex_lock+0x238/0x488 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x50/0x74 clk_prepare_lock+0x7c/0x9c clk_core_prepare_lock+0x20/0x44 clk_prepare+0x24/0x30 clk_bulk_prepare+0x40/0xb0 mdss_runtime_resume+0x54/0x1c8 pm_generic_runtime_resume+0x30/0x44 __genpd_runtime_resume+0x68/0x7c genpd_runtime_resume+0x108/0x1f4 __rpm_callback+0x84/0x144 rpm_callback+0x30/0x88 rpm_resume+0x1f4/0x52c rpm_resume+0x178/0x52c __pm_runtime_resume+0x58/0x98 __device_attach+0xe0/0x170 device_initial_probe+0x1c/0x28 bus_probe_device+0x3c/0x9c device_add+0x644/0x814 mipi_dsi_device_register_full+0xe4/0x170 devm_mipi_dsi_device_register_full+0x28/0x70 ti_sn_bridge_probe+0x1dc/0x2c0 auxiliary_bus_probe+0x4c/0x94 really_probe+0xcc/0x2c8 __driver_probe_device+0xa8/0x130 driver_probe_device+0x48/0x110 __device_attach_driver+0xa4/0xcc bus_for_each_drv+0x8c/0xd8 __device_attach+0xf8/0x170 device_initial_probe+0x1c/0x28 bus_probe_device+0x3c/0x9c deferred_probe_work_func+0x9c/0xd8 process_one_work+0x148/0x518 worker_thread+0x138/0x350 kthread+0x138/0x1e0 ret_from_fork+0x10/0x20 The first thread is walking the clk tree and calling clk_pm_runtime_get() to power on devices required to read the clk hardware via struct clk_ops::is_enabled(). This thread holds the clk prepare_lock, and is trying to runtime PM resume a device, when it finds that the device is in the process of resuming so the thread schedule()s away waiting for the device to finish resuming before continuing. The second thread is runtime PM resuming the same device, but the runtime resume callback is calling clk_prepare(), trying to grab the prepare_lock waiting on the first thread. This is a classic ABBA deadlock. To properly fix the deadlock, we must never runtime PM resume or suspend a device with the clk prepare_lock held. Actually doing that is near impossible today because the global prepare_lock would have to be dropped in the middle of the tree, the device runtime PM resumed/suspended, and then the prepare_lock grabbed again to ensure consistency of the clk tree topology. If anything changes with the clk tree in the meantime, we've lost and will need to start the operation all over again. Luckily, most of the time we're simply incrementing or decrementing the runtime PM count on an active device, so we don't have the chance to schedule away with the prepare_lock held. Let's fix this immediate problem that can be triggered more easily by simply booting on Qualcomm sc7180. Introduce a list of clk_core structures that have been registered, or are in the process of being registered, that require runtime PM to operate. Iterate this list and call clk_pm_runtime_get() on each of them without holding the prepare_lock during clk_disable_unused(). This way we can be certain that the runtime PM state of the devices will be active and resumed so we can't schedule away while walking the clk tree with the prepare_lock held. Similarly, call clk_pm_runtime_put() without the prepare_lock held to properly drop the runtime PM reference. We remove the calls to clk_pm_runtime_{get,put}() in this path because they're superfluous now that we know the devices are runtime resumed. Reported-by: Douglas Anderson Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1] Closes: https://issuetracker.google.com/328070191 Cc: Marek Szyprowski Cc: Ulf Hansson Cc: Krzysztof Kozlowski Fixes: 9a34b45397e5 ("clk: Add support for runtime PM") Signed-off-by: Stephen Boyd Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org Reviewed-by: Douglas Anderson Signed-off-by: Sasha Levin --- drivers/clk/clk.c | 117 +++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 105 insertions(+), 12 deletions(-) diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c index f887cea057ee..59a77587da47 100644 --- a/drivers/clk/clk.c +++ b/drivers/clk/clk.c @@ -37,6 +37,10 @@ static HLIST_HEAD(clk_root_list); static HLIST_HEAD(clk_orphan_list); static LIST_HEAD(clk_notifier_list); +/* List of registered clks that use runtime PM */ +static HLIST_HEAD(clk_rpm_list); +static DEFINE_MUTEX(clk_rpm_list_lock); + static const struct hlist_head *all_lists[] = { &clk_root_list, &clk_orphan_list, @@ -59,6 +63,7 @@ struct clk_core { struct clk_hw *hw; struct module *owner; struct device *dev; + struct hlist_node rpm_node; struct device_node *of_node; struct clk_core *parent; struct clk_parent_map *parents; @@ -129,6 +134,89 @@ static void clk_pm_runtime_put(struct clk_core *core) pm_runtime_put_sync(core->dev); } +/** + * clk_pm_runtime_get_all() - Runtime "get" all clk provider devices + * + * Call clk_pm_runtime_get() on all runtime PM enabled clks in the clk tree so + * that disabling unused clks avoids a deadlock where a device is runtime PM + * resuming/suspending and the runtime PM callback is trying to grab the + * prepare_lock for something like clk_prepare_enable() while + * clk_disable_unused_subtree() holds the prepare_lock and is trying to runtime + * PM resume/suspend the device as well. + * + * Context: Acquires the 'clk_rpm_list_lock' and returns with the lock held on + * success. Otherwise the lock is released on failure. + * + * Return: 0 on success, negative errno otherwise. + */ +static int clk_pm_runtime_get_all(void) +{ + int ret; + struct clk_core *core, *failed; + + /* + * Grab the list lock to prevent any new clks from being registered + * or unregistered until clk_pm_runtime_put_all(). + */ + mutex_lock(&clk_rpm_list_lock); + + /* + * Runtime PM "get" all the devices that are needed for the clks + * currently registered. Do this without holding the prepare_lock, to + * avoid the deadlock. + */ + hlist_for_each_entry(core, &clk_rpm_list, rpm_node) { + ret = clk_pm_runtime_get(core); + if (ret) { + failed = core; + pr_err("clk: Failed to runtime PM get '%s' for clk '%s'\n", + dev_name(failed->dev), failed->name); + goto err; + } + } + + return 0; + +err: + hlist_for_each_entry(core, &clk_rpm_list, rpm_node) { + if (core == failed) + break; + + clk_pm_runtime_put(core); + } + mutex_unlock(&clk_rpm_list_lock); + + return ret; +} + +/** + * clk_pm_runtime_put_all() - Runtime "put" all clk provider devices + * + * Put the runtime PM references taken in clk_pm_runtime_get_all() and release + * the 'clk_rpm_list_lock'. + */ +static void clk_pm_runtime_put_all(void) +{ + struct clk_core *core; + + hlist_for_each_entry(core, &clk_rpm_list, rpm_node) + clk_pm_runtime_put(core); + mutex_unlock(&clk_rpm_list_lock); +} + +static void clk_pm_runtime_init(struct clk_core *core) +{ + struct device *dev = core->dev; + + if (dev && pm_runtime_enabled(dev)) { + core->rpm_enabled = true; + + mutex_lock(&clk_rpm_list_lock); + hlist_add_head(&core->rpm_node, &clk_rpm_list); + mutex_unlock(&clk_rpm_list_lock); + } +} + /*** locking ***/ static void clk_prepare_lock(void) { @@ -1237,9 +1325,6 @@ static void clk_unprepare_unused_subtree(struct clk_core *core) if (core->flags & CLK_IGNORE_UNUSED) return; - if (clk_pm_runtime_get(core)) - return; - if (clk_core_is_prepared(core)) { trace_clk_unprepare(core); if (core->ops->unprepare_unused) @@ -1248,8 +1333,6 @@ static void clk_unprepare_unused_subtree(struct clk_core *core) core->ops->unprepare(core->hw); trace_clk_unprepare_complete(core); } - - clk_pm_runtime_put(core); } static void clk_disable_unused_subtree(struct clk_core *core) @@ -1265,9 +1348,6 @@ static void clk_disable_unused_subtree(struct clk_core *core) if (core->flags & CLK_OPS_PARENT_ENABLE) clk_core_prepare_enable(core->parent); - if (clk_pm_runtime_get(core)) - goto unprepare_out; - flags = clk_enable_lock(); if (core->enable_count) @@ -1292,8 +1372,6 @@ static void clk_disable_unused_subtree(struct clk_core *core) unlock_out: clk_enable_unlock(flags); - clk_pm_runtime_put(core); -unprepare_out: if (core->flags & CLK_OPS_PARENT_ENABLE) clk_core_disable_unprepare(core->parent); } @@ -1309,6 +1387,7 @@ __setup("clk_ignore_unused", clk_ignore_unused_setup); static int clk_disable_unused(void) { struct clk_core *core; + int ret; if (clk_ignore_unused) { pr_warn("clk: Not disabling unused clocks\n"); @@ -1317,6 +1396,13 @@ static int clk_disable_unused(void) pr_info("clk: Disabling unused clocks\n"); + ret = clk_pm_runtime_get_all(); + if (ret) + return ret; + /* + * Grab the prepare lock to keep the clk topology stable while iterating + * over clks. + */ clk_prepare_lock(); hlist_for_each_entry(core, &clk_root_list, child_node) @@ -1333,6 +1419,8 @@ static int clk_disable_unused(void) clk_prepare_unlock(); + clk_pm_runtime_put_all(); + return 0; } late_initcall_sync(clk_disable_unused); @@ -3723,6 +3811,12 @@ static void __clk_release(struct kref *ref) { struct clk_core *core = container_of(ref, struct clk_core, ref); + if (core->rpm_enabled) { + mutex_lock(&clk_rpm_list_lock); + hlist_del(&core->rpm_node); + mutex_unlock(&clk_rpm_list_lock); + } + clk_core_free_parent_map(core); kfree_const(core->name); kfree(core); @@ -3762,9 +3856,8 @@ __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw) } core->ops = init->ops; - if (dev && pm_runtime_enabled(dev)) - core->rpm_enabled = true; core->dev = dev; + clk_pm_runtime_init(core); core->of_node = np; if (dev && dev->driver) core->owner = dev->driver->owner; From 58ecead174f81167bdecc4e88a2a8e51949240be Mon Sep 17 00:00:00 2001 From: Eric Biggers Date: Tue, 16 Apr 2024 23:04:34 -0700 Subject: [PATCH 034/107] x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ [ Upstream commit 9543f6e26634537997b6e909c20911b7bf4876de ] Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs that support these features but not AVX512. GFNI actually doesn't even depend on AVX. This prevents GFNI from being unnecessarily disabled if AVX is disabled to mitigate the GDS vulnerability. This also prevents all three features from being unnecessarily disabled if AVX512VL (or its dependency AVX512F) were to be disabled, but it looks like there isn't any case where this happens anyway. Fixes: c128dbfa0f87 ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features") Signed-off-by: Eric Biggers Signed-off-by: Borislav Petkov (AMD) Acked-by: Dave Hansen Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org Signed-off-by: Sasha Levin --- arch/x86/kernel/cpu/cpuid-deps.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/x86/kernel/cpu/cpuid-deps.c b/arch/x86/kernel/cpu/cpuid-deps.c index 3cbe24ca80ab..f50d4422c7b5 100644 --- a/arch/x86/kernel/cpu/cpuid-deps.c +++ b/arch/x86/kernel/cpu/cpuid-deps.c @@ -44,7 +44,10 @@ static const struct cpuid_dep cpuid_deps[] = { { X86_FEATURE_F16C, X86_FEATURE_XMM2, }, { X86_FEATURE_AES, X86_FEATURE_XMM2 }, { X86_FEATURE_SHA_NI, X86_FEATURE_XMM2 }, + { X86_FEATURE_GFNI, X86_FEATURE_XMM2 }, { X86_FEATURE_FMA, X86_FEATURE_AVX }, + { X86_FEATURE_VAES, X86_FEATURE_AVX }, + { X86_FEATURE_VPCLMULQDQ, X86_FEATURE_AVX }, { X86_FEATURE_AVX2, X86_FEATURE_AVX, }, { X86_FEATURE_AVX512F, X86_FEATURE_AVX, }, { X86_FEATURE_AVX512IFMA, X86_FEATURE_AVX512F }, @@ -56,9 +59,6 @@ static const struct cpuid_dep cpuid_deps[] = { { X86_FEATURE_AVX512VL, X86_FEATURE_AVX512F }, { X86_FEATURE_AVX512VBMI, X86_FEATURE_AVX512F }, { X86_FEATURE_AVX512_VBMI2, X86_FEATURE_AVX512VL }, - { X86_FEATURE_GFNI, X86_FEATURE_AVX512VL }, - { X86_FEATURE_VAES, X86_FEATURE_AVX512VL }, - { X86_FEATURE_VPCLMULQDQ, X86_FEATURE_AVX512VL }, { X86_FEATURE_AVX512_VNNI, X86_FEATURE_AVX512VL }, { X86_FEATURE_AVX512_BITALG, X86_FEATURE_AVX512VL }, { X86_FEATURE_AVX512_4VNNIW, X86_FEATURE_AVX512F }, From 68a28f551e4690db2b27b3db716c7395f6fada12 Mon Sep 17 00:00:00 2001 From: Carlos Llamas Date: Sat, 30 Mar 2024 19:01:14 +0000 Subject: [PATCH 035/107] binder: check offset alignment in binder_get_object() commit aaef73821a3b0194a01bd23ca77774f704a04d40 upstream. Commit 6d98eb95b450 ("binder: avoid potential data leakage when copying txn") introduced changes to how binder objects are copied. In doing so, it unintentionally removed an offset alignment check done through calls to binder_alloc_copy_from_buffer() -> check_buffer(). These calls were replaced in binder_get_object() with copy_from_user(), so now an explicit offset alignment check is needed here. This avoids later complications when unwinding the objects gets harder. It is worth noting this check existed prior to commit 7a67a39320df ("binder: add function to copy binder object from buffer"), likely removed due to redundancy at the time. Fixes: 6d98eb95b450 ("binder: avoid potential data leakage when copying txn") Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas Acked-by: Todd Kjos Link: https://lore.kernel.org/r/20240330190115.1877819-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman --- drivers/android/binder.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/android/binder.c b/drivers/android/binder.c index 07203fef29cb..0fe56dcdf441 100644 --- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -2047,8 +2047,10 @@ static size_t binder_get_object(struct binder_proc *proc, size_t object_size = 0; read_size = min_t(size_t, sizeof(*object), buffer->data_size - offset); - if (offset > buffer->data_size || read_size < sizeof(*hdr)) + if (offset > buffer->data_size || read_size < sizeof(*hdr) || + !IS_ALIGNED(offset, sizeof(u32))) return 0; + if (u) { if (copy_from_user(object, u + offset, read_size)) return 0; From a3b8ae7e9297dd453f2977b011c5bc75eb20e71b Mon Sep 17 00:00:00 2001 From: Nikita Zhandarovich Date: Mon, 8 Apr 2024 10:16:33 -0700 Subject: [PATCH 036/107] comedi: vmk80xx: fix incomplete endpoint checking commit d1718530e3f640b7d5f0050e725216eab57a85d8 upstream. While vmk80xx does have endpoint checking implemented, some things can fall through the cracks. Depending on the hardware model, URBs can have either bulk or interrupt type, and current version of vmk80xx_find_usb_endpoints() function does not take that fully into account. While this warning does not seem to be too harmful, at the very least it will crash systems with 'panic_on_warn' set on them. Fix the issue found by Syzkaller [1] by somewhat simplifying the endpoint checking process with usb_find_common_endpoints() and ensuring that only expected endpoint types are present. This patch has not been tested on real hardware. [1] Syzkaller report: usb 1-1: BOGUS urb xfer, pipe 1 != type 3 WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503 ... Call Trace: usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59 vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline] vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818 comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067 usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399 ... Similar issue also found by Syzkaller: Link: https://syzkaller.appspot.com/bug?extid=5205eb2f17de3e01946e Reported-and-tested-by: syzbot+5f29dc6a889fc42bd896@syzkaller.appspotmail.com Cc: stable Fixes: 49253d542cc0 ("staging: comedi: vmk80xx: factor out usb endpoint detection") Reviewed-by: Ian Abbott Signed-off-by: Nikita Zhandarovich Link: https://lore.kernel.org/r/20240408171633.31649-1-n.zhandarovich@fintech.ru Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/vmk80xx.c | 35 ++++++++---------------- 1 file changed, 12 insertions(+), 23 deletions(-) diff --git a/drivers/staging/comedi/drivers/vmk80xx.c b/drivers/staging/comedi/drivers/vmk80xx.c index ccc65cfc519f..51b814e44783 100644 --- a/drivers/staging/comedi/drivers/vmk80xx.c +++ b/drivers/staging/comedi/drivers/vmk80xx.c @@ -642,32 +642,21 @@ static int vmk80xx_find_usb_endpoints(struct comedi_device *dev) struct vmk80xx_private *devpriv = dev->private; struct usb_interface *intf = comedi_to_usb_interface(dev); struct usb_host_interface *iface_desc = intf->cur_altsetting; - struct usb_endpoint_descriptor *ep_desc; - int i; + struct usb_endpoint_descriptor *ep_rx_desc, *ep_tx_desc; + int ret; - if (iface_desc->desc.bNumEndpoints != 2) + if (devpriv->model == VMK8061_MODEL) + ret = usb_find_common_endpoints(iface_desc, &ep_rx_desc, + &ep_tx_desc, NULL, NULL); + else + ret = usb_find_common_endpoints(iface_desc, NULL, NULL, + &ep_rx_desc, &ep_tx_desc); + + if (ret) return -ENODEV; - for (i = 0; i < iface_desc->desc.bNumEndpoints; i++) { - ep_desc = &iface_desc->endpoint[i].desc; - - if (usb_endpoint_is_int_in(ep_desc) || - usb_endpoint_is_bulk_in(ep_desc)) { - if (!devpriv->ep_rx) - devpriv->ep_rx = ep_desc; - continue; - } - - if (usb_endpoint_is_int_out(ep_desc) || - usb_endpoint_is_bulk_out(ep_desc)) { - if (!devpriv->ep_tx) - devpriv->ep_tx = ep_desc; - continue; - } - } - - if (!devpriv->ep_rx || !devpriv->ep_tx) - return -ENODEV; + devpriv->ep_rx = ep_rx_desc; + devpriv->ep_tx = ep_tx_desc; if (!usb_endpoint_maxp(devpriv->ep_rx) || !usb_endpoint_maxp(devpriv->ep_tx)) return -EINVAL; From d679c816929d62af51c8e6d7fc0e165c9412d2f3 Mon Sep 17 00:00:00 2001 From: Finn Thain Date: Mon, 8 Apr 2024 19:23:43 +1000 Subject: [PATCH 037/107] serial/pmac_zilog: Remove flawed mitigation for rx irq flood commit 1be3226445362bfbf461c92a5bcdb1723f2e4907 upstream. The mitigation was intended to stop the irq completely. That may be better than a hard lock-up but it turns out that you get a crash anyway if you're using pmac_zilog as a serial console: ttyPZ0: pmz: rx irq flood ! BUG: spinlock recursion on CPU#0, swapper/0 That's because the pr_err() call in pmz_receive_chars() results in pmz_console_write() attempting to lock a spinlock already locked in pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal BUG splat. The spinlock in question is the one in struct uart_port. Even when it's not fatal, the serial port rx function ceases to work. Also, the iteration limit doesn't play nicely with QEMU, as can be seen in the bug report linked below. A web search for other reports of the error message "pmz: rx irq flood" didn't produce anything. So I don't think this code is needed any more. Remove it. Cc: Benjamin Herrenschmidt Cc: Michael Ellerman Cc: Nicholas Piggin Cc: Christophe Leroy Cc: Aneesh Kumar K.V Cc: Naveen N. Rao Cc: Andy Shevchenko Cc: stable@kernel.org Cc: linux-m68k@lists.linux-m68k.org Link: https://github.com/vivier/qemu-m68k/issues/44 Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/ Acked-by: Michael Ellerman Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable Signed-off-by: Finn Thain Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/pmac_zilog.c | 14 -------------- 1 file changed, 14 deletions(-) diff --git a/drivers/tty/serial/pmac_zilog.c b/drivers/tty/serial/pmac_zilog.c index bcb5bf70534e..5ea3b92689c7 100644 --- a/drivers/tty/serial/pmac_zilog.c +++ b/drivers/tty/serial/pmac_zilog.c @@ -220,7 +220,6 @@ static bool pmz_receive_chars(struct uart_pmac_port *uap) { struct tty_port *port; unsigned char ch, r1, drop, flag; - int loops = 0; /* Sanity check, make sure the old bug is no longer happening */ if (uap->port.state == NULL) { @@ -301,24 +300,11 @@ static bool pmz_receive_chars(struct uart_pmac_port *uap) if (r1 & Rx_OVR) tty_insert_flip_char(port, 0, TTY_OVERRUN); next_char: - /* We can get stuck in an infinite loop getting char 0 when the - * line is in a wrong HW state, we break that here. - * When that happens, I disable the receive side of the driver. - * Note that what I've been experiencing is a real irq loop where - * I'm getting flooded regardless of the actual port speed. - * Something strange is going on with the HW - */ - if ((++loops) > 1000) - goto flood; ch = read_zsreg(uap, R0); if (!(ch & Rx_CH_AV)) break; } - return true; - flood: - pmz_interrupt_control(uap, 0); - pmz_error("pmz: rx irq flood !\n"); return true; } From fc693ec145b3775bfd26b13c2cab8962351b48a2 Mon Sep 17 00:00:00 2001 From: bolan wang Date: Wed, 6 Mar 2024 19:03:39 +0800 Subject: [PATCH 038/107] USB: serial: option: add Fibocom FM135-GL variants commit 356952b13af5b2c338df1e06889fd1b5e12cbbf4 upstream. Update the USB serial option driver support for the Fibocom FM135-GL LTE modules. - VID:PID 2cb7:0115, FM135-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS) 0x0115: mbim, diag, at, pipe Here are the outputs of usb-devices: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0115 Rev=05.15 S: Manufacturer=Fibocom Wireless Inc. S: Product=Fibocom Module S: SerialNumber=12345678 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: bolan wang Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 17c3044c2d26..d0f231d1b890 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -2272,6 +2272,8 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) }, /* Fibocom FG150 Diag */ { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) }, /* Fibocom FG150 AT */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0111, 0xff) }, /* Fibocom FM160 (MBIM mode) */ + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0115, 0xff), /* Fibocom FM135 (laptop MBIM) */ + .driver_info = RSVD(5) }, { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) }, /* Fibocom NL668-AM/NL652-EU (laptop MBIM) */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff) }, /* Fibocom FM101-GL (laptop MBIM) */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a3, 0xff) }, /* Fibocom FM101-GL (laptop MBIM) */ From 8e5ddf4a8a1f17041b67ebc7d18be2c430218f55 Mon Sep 17 00:00:00 2001 From: Chuanhong Guo Date: Tue, 12 Mar 2024 14:29:12 +0800 Subject: [PATCH 039/107] USB: serial: option: add support for Fibocom FM650/FG650 commit fb1f4584b1215e8c209f6b3a4028ed8351a0e961 upstream. Fibocom FM650/FG650 are 5G modems with ECM/NCM/RNDIS/MBIM modes. This patch adds support to all 4 modes. In all 4 modes, the first serial port is the AT console while the other 3 appear to be diagnostic interfaces for dumping modem logs. usb-devices output for all modes: ECM: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=2cb7 ProdID=0a04 Rev=04.04 S: Manufacturer=Fibocom Wireless Inc. S: Product=FG650 Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=504mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms NCM: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=2cb7 ProdID=0a05 Rev=04.04 S: Manufacturer=Fibocom Wireless Inc. S: Product=FG650 Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms RNDIS: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=2cb7 ProdID=0a06 Rev=04.04 S: Manufacturer=Fibocom Wireless Inc. S: Product=FG650 Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms MBIM: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=5000 MxCh= 0 D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=2cb7 ProdID=0a07 Rev=04.04 S: Manufacturer=Fibocom Wireless Inc. S: Product=FG650 Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms Signed-off-by: Chuanhong Guo Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index d0f231d1b890..7c5c82bb028e 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -2279,6 +2279,10 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a3, 0xff) }, /* Fibocom FM101-GL (laptop MBIM) */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4, 0xff), /* Fibocom FM101-GL (laptop MBIM) */ .driver_info = RSVD(4) }, + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a04, 0xff) }, /* Fibocom FM650-CN (ECM mode) */ + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a05, 0xff) }, /* Fibocom FM650-CN (NCM mode) */ + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a06, 0xff) }, /* Fibocom FM650-CN (RNDIS mode) */ + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a07, 0xff) }, /* Fibocom FM650-CN (MBIM mode) */ { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff) }, /* LongSung M5710 */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) }, /* GosunCn GM500 RNDIS */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) }, /* GosunCn GM500 MBIM */ From 1224818578ebe00a6473310665c60be3d031ad1c Mon Sep 17 00:00:00 2001 From: Coia Prant Date: Mon, 15 Apr 2024 07:26:25 -0700 Subject: [PATCH 040/107] USB: serial: option: add Lonsung U8300/U9300 product commit cf16ffa17c398434a77b8a373e69287c95b60de2 upstream. Update the USB serial option driver to support Longsung U8300/U9300. For U8300 Interface 4 is used by for QMI interface in stock firmware of U8300, the router which uses U8300 modem. Interface 5 is used by for ADB interface in stock firmware of U8300, the router which uses U8300 modem. Interface mapping is: 0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB T: Bus=05 Lev=01 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b05 Rev=03.18 S: Manufacturer=Android S: Product=Android C: #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms For U9300 Interface 1 is used by for ADB interface in stock firmware of U9300, the router which uses U9300 modem. Interface 4 is used by for QMI interface in stock firmware of U9300, the router which uses U9300 modem. Interface mapping is: 0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI Note: Interface 3 of some models of the U9300 series can send AT commands. T: Bus=05 Lev=01 Prnt=05 Port=04 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b3c Rev=03.18 S: Manufacturer=Android S: Product=Android C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms Tested successfully using Modem Manager on U9300. Tested successfully AT commands using If=1, If=2 and If=3 on U9300. Signed-off-by: Coia Prant Reviewed-by: Lars Melin [ johan: drop product defines, trim commit message ] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 7c5c82bb028e..9af7c04690c1 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -2052,6 +2052,10 @@ static const struct usb_device_id option_ids[] = { .driver_info = RSVD(3) }, { USB_DEVICE_INTERFACE_CLASS(LONGCHEER_VENDOR_ID, 0x9803, 0xff), .driver_info = RSVD(4) }, + { USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b05), /* Longsung U8300 */ + .driver_info = RSVD(4) | RSVD(5) }, + { USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b3c), /* Longsung U9300 */ + .driver_info = RSVD(0) | RSVD(4) }, { USB_DEVICE(LONGCHEER_VENDOR_ID, ZOOM_PRODUCT_4597) }, { USB_DEVICE(LONGCHEER_VENDOR_ID, IBALL_3_5G_CONNECT) }, { USB_DEVICE(HAIER_VENDOR_ID, HAIER_PRODUCT_CE100) }, From 386fb39ea321d38b1626523220342d07f9cd3fb4 Mon Sep 17 00:00:00 2001 From: Jerry Meng Date: Mon, 15 Apr 2024 15:04:29 +0800 Subject: [PATCH 041/107] USB: serial: option: support Quectel EM060K sub-models commit c840244aba7ad2b83ed904378b36bd6aef25511c upstream. EM060K_129, EM060K_12a, EM060K_12b and EM0060K_12c are EM060K's sub-models, having the same name "Quectel EM060K-GL" and the same interface layout. MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0129 Rev= 5.04 S: Manufacturer=Quectel S: Product=Quectel EM060K-GL S: SerialNumber=f6fa08b6 C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Jerry Meng Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 9af7c04690c1..c92bcb53c9ec 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -255,6 +255,10 @@ static void option_instat_callback(struct urb *urb); #define QUECTEL_PRODUCT_EM061K_LMS 0x0124 #define QUECTEL_PRODUCT_EC25 0x0125 #define QUECTEL_PRODUCT_EM060K_128 0x0128 +#define QUECTEL_PRODUCT_EM060K_129 0x0129 +#define QUECTEL_PRODUCT_EM060K_12a 0x012a +#define QUECTEL_PRODUCT_EM060K_12b 0x012b +#define QUECTEL_PRODUCT_EM060K_12c 0x012c #define QUECTEL_PRODUCT_EG91 0x0191 #define QUECTEL_PRODUCT_EG95 0x0195 #define QUECTEL_PRODUCT_BG96 0x0296 @@ -1218,6 +1222,18 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0x00, 0x40) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x30) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0x00, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x30) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0x00, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x30) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0x00, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x30) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0x00, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x40) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0x00, 0x40) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x40) }, From 3a7fca20cb78d6ba7f95b74dfdef38c3a43ae4e5 Mon Sep 17 00:00:00 2001 From: Vanillan Wang Date: Tue, 16 Apr 2024 18:02:55 +0800 Subject: [PATCH 042/107] USB: serial: option: add Rolling RW101-GL and RW135-GL support commit 311f97a4c7c22a01f8897bddf00428dfd0668e79 upstream. Update the USB serial option driver support for the Rolling LTE modules. - VID:PID 33f8:01a2, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS) 0x01a2: mbim, diag, at, pipe - VID:PID 33f8:01a3, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS) 0x01a3: mbim, pipe - VID:PID 33f8:01a4, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS) 0x01a4: mbim, diag, at, pipe - VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET interface for /Linux/Chrome OS) 0x0104: RMNET, diag, at, pipe - VID:PID 33f8:0115, RW135-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS) 0x0115: MBIM, diag, at, pipe Here are the outputs of usb-devices: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=33f8 ProdID=01a2 Rev=05.15 S: Manufacturer=Rolling Wireless S.a.r.l. S: Product=Rolling Module S: SerialNumber=12345678 C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=33f8 ProdID=01a3 Rev=05.15 S: Manufacturer=Rolling Wireless S.a.r.l. S: Product=Rolling Module S: SerialNumber=12345678 C: #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=33f8 ProdID=01a4 Rev=05.15 S: Manufacturer=Rolling Wireless S.a.r.l. S: Product=Rolling Module S: SerialNumber=12345678 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=33f8 ProdID=0104 Rev=05.04 S: Manufacturer=Rolling Wireless S.a.r.l. S: Product=Rolling Module S: SerialNumber=ba2eb033 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=33f8 ProdID=0115 Rev=05.15 S: Manufacturer=Rolling Wireless S.a.r.l. S: Product=Rolling Module S: SerialNumber=12345678 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Vanillan Wang Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index c92bcb53c9ec..ecaa801084a4 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -2307,6 +2307,14 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) }, /* GosunCn GM500 RNDIS */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) }, /* GosunCn GM500 MBIM */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1406, 0xff) }, /* GosunCn GM500 ECM/NCM */ + { USB_DEVICE(0x33f8, 0x0104), /* Rolling RW101-GL (laptop RMNET) */ + .driver_info = RSVD(4) | RSVD(5) }, + { USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a2, 0xff) }, /* Rolling RW101-GL (laptop MBIM) */ + { USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a3, 0xff) }, /* Rolling RW101-GL (laptop MBIM) */ + { USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a4, 0xff), /* Rolling RW101-GL (laptop MBIM) */ + .driver_info = RSVD(4) }, + { USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x0115, 0xff), /* Rolling RW135-GL (laptop MBIM) */ + .driver_info = RSVD(5) }, { USB_DEVICE_AND_INTERFACE_INFO(OPPO_VENDOR_ID, OPPO_PRODUCT_R11, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x40) }, From 11a3e5c76e8cdf454c7135f3c5157da301d059db Mon Sep 17 00:00:00 2001 From: Daniele Palmas Date: Thu, 18 Apr 2024 13:34:30 +0200 Subject: [PATCH 043/107] USB: serial: option: add Telit FN920C04 rmnet compositions commit 582ee2f9d268d302595db3e36b985e5cbb93284d upstream. Add the following Telit FN920C04 compositions: 0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag) T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10a0 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FN920 S: SerialNumber=92c4c4d8 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag) T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10a4 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FN920 S: SerialNumber=92c4c4d8 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10a9 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FN920 S: SerialNumber=92c4c4d8 C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Daniele Palmas Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ecaa801084a4..9ebd314a791d 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1376,6 +1376,12 @@ static const struct usb_device_id option_ids[] = { .driver_info = NCTRL(2) | RSVD(3) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff), /* Telit FE990 (ECM) */ .driver_info = NCTRL(0) | RSVD(1) }, + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a0, 0xff), /* Telit FN20C04 (rmnet) */ + .driver_info = RSVD(0) | NCTRL(3) }, + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a4, 0xff), /* Telit FN20C04 (rmnet) */ + .driver_info = RSVD(0) | NCTRL(3) }, + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a9, 0xff), /* Telit FN20C04 (rmnet) */ + .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910), .driver_info = NCTRL(0) | RSVD(1) | RSVD(3) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM), From 164be0a824387301312689bb29b2be92ab2cd39d Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Thu, 18 Apr 2024 16:33:28 +0200 Subject: [PATCH 044/107] Revert "usb: cdc-wdm: close race between read and workqueue" MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream. This reverts commit 339f83612f3a569b194680768b22bf113c26a29d. It has been found to cause problems in a number of Chromebook devices, so revert the change until it can be brought back in a safe way. Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org Reported-by:: Aleksander Morgado Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue") Cc: stable Cc: Oliver Neukum Cc: Bjørn Mork Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-wdm.c | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-) diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c index 18ecd5a93539..98022584f709 100644 --- a/drivers/usb/class/cdc-wdm.c +++ b/drivers/usb/class/cdc-wdm.c @@ -471,7 +471,6 @@ out_free_mem: static int service_outstanding_interrupt(struct wdm_device *desc) { int rv = 0; - int used; /* submit read urb only if the device is waiting for it */ if (!desc->resp_count || !--desc->resp_count) @@ -486,10 +485,7 @@ static int service_outstanding_interrupt(struct wdm_device *desc) goto out; } - used = test_and_set_bit(WDM_RESPONDING, &desc->flags); - if (used) - goto out; - + set_bit(WDM_RESPONDING, &desc->flags); spin_unlock_irq(&desc->iuspin); rv = usb_submit_urb(desc->response, GFP_KERNEL); spin_lock_irq(&desc->iuspin); From 75bf5e78b2a27cb1bca6fa826e3ab685015165e1 Mon Sep 17 00:00:00 2001 From: Minas Harutyunyan Date: Tue, 9 Apr 2024 12:27:54 +0000 Subject: [PATCH 045/107] usb: dwc2: host: Fix dereference issue in DDMA completion flow. commit eed04fa96c48790c1cce73c8a248e9d460b088f8 upstream. Fixed variable dereference issue in DDMA completion flow. Fixes: b258e4268850 ("usb: dwc2: host: Fix ISOC flow in DDMA mode") CC: stable@vger.kernel.org Reported-by: Dan Carpenter Closes: https://lore.kernel.org/linux-usb/2024040834-ethically-rumble-701f@gregkh/T/#m4c4b83bef0ebb4b67fe2e0a7d6466cbb6f416e39 Signed-off-by: Minas Harutyunyan Link: https://lore.kernel.org/r/cc826d3ef53c934d8e6d98870f17f3cdc3d2755d.1712665387.git.Minas.Harutyunyan@synopsys.com Signed-off-by: Greg Kroah-Hartman --- drivers/usb/dwc2/hcd_ddma.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/usb/dwc2/hcd_ddma.c b/drivers/usb/dwc2/hcd_ddma.c index 6a4aa71da103..d6fa02d851e4 100644 --- a/drivers/usb/dwc2/hcd_ddma.c +++ b/drivers/usb/dwc2/hcd_ddma.c @@ -897,13 +897,15 @@ static int dwc2_cmpl_host_isoc_dma_desc(struct dwc2_hsotg *hsotg, struct dwc2_dma_desc *dma_desc; struct dwc2_hcd_iso_packet_desc *frame_desc; u16 frame_desc_idx; - struct urb *usb_urb = qtd->urb->priv; + struct urb *usb_urb; u16 remain = 0; int rc = 0; if (!qtd->urb) return -EINVAL; + usb_urb = qtd->urb->priv; + dma_sync_single_for_cpu(hsotg->dev, qh->desc_list_dma + (idx * sizeof(struct dwc2_dma_desc)), sizeof(struct dwc2_dma_desc), From c64704f0802b85a21dd6cd7181538e0899fef8ed Mon Sep 17 00:00:00 2001 From: Kai-Heng Feng Date: Tue, 5 Mar 2024 14:51:38 +0800 Subject: [PATCH 046/107] usb: Disable USB3 LPM at shutdown commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream. SanDisks USB3 storage may disapper after system reboot: usb usb2-port3: link state change xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 usb usb2-port3: do warm reset, port only xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0 usb usb2-port3: not warm reset yet, waiting 50ms xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0 usb usb2-port3: not warm reset yet, waiting 200ms ... xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0 usb usb2-port3: not warm reset yet, waiting 200ms xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0 usb usb2-port3: not enabled, trying warm reset again... This is due to the USB device still cause port change event after xHCI is shuted down: xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001 xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling. xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0 xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling. xhci_hcd 0000:38:00.0: // Halt the HC xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling. xhci_hcd 0000:00:14.0: // Halt the HC xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203 xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 usb 2-3: device not accepting address 2, error -108 xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1 usb usb2-port3: not reset yet, waiting 60ms ACPI: PM: Preparing to enter system sleep state S5 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1 usb usb2-port3: not reset yet, waiting 200ms reboot: Restarting system The port change event is caused by LPM transition, so disabling LPM at shutdown to make sure the device is in U0 for warmboot. Signed-off-by: Kai-Heng Feng Cc: stable Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/port.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/usb/core/port.c b/drivers/usb/core/port.c index 336ecf6e1967..86e8585a5512 100644 --- a/drivers/usb/core/port.c +++ b/drivers/usb/core/port.c @@ -295,8 +295,10 @@ static void usb_port_shutdown(struct device *dev) { struct usb_port *port_dev = to_usb_port(dev); - if (port_dev->child) + if (port_dev->child) { usb_disable_usb2_hardware_lpm(port_dev->child); + usb_unlocked_disable_lpm(port_dev->child); + } } static const struct dev_pm_ops usb_port_pm_ops = { From 8f6b62125befe1675446923e4171eac2c012959c Mon Sep 17 00:00:00 2001 From: Samuel Thibault Date: Sat, 23 Mar 2024 17:48:43 +0100 Subject: [PATCH 047/107] speakup: Avoid crash on very long word commit c8d2f34ea96ea3bce6ba2535f867f0d4ee3b22e1 upstream. In case a console is set up really large and contains a really long word (> 256 characters), we have to stop before the length of the word buffer. Signed-off-by: Samuel Thibault Fixes: c6e3fd22cd538 ("Staging: add speakup to the staging directory") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240323164843.1426997-1-samuel.thibault@ens-lyon.org Signed-off-by: Greg Kroah-Hartman --- drivers/staging/speakup/main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/staging/speakup/main.c b/drivers/staging/speakup/main.c index 11c3b47b8a22..08b07e77bb9d 100644 --- a/drivers/staging/speakup/main.c +++ b/drivers/staging/speakup/main.c @@ -577,7 +577,7 @@ static u_long get_word(struct vc_data *vc) } attr_ch = get_char(vc, (u_short *)tmp_pos, &spk_attr); buf[cnt++] = attr_ch; - while (tmpx < vc->vc_cols - 1) { + while (tmpx < vc->vc_cols - 1 && cnt < sizeof(buf) - 1) { tmp_pos += 2; tmpx++; ch = get_char(vc, (u_short *)tmp_pos, &temp); From 57baab0f376bec8f54b0fe6beb8f77a57c228063 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Wed, 13 Mar 2024 17:43:41 -0400 Subject: [PATCH 048/107] fs: sysfs: Fix reference leak in sysfs_break_active_protection() commit a90bca2228c0646fc29a72689d308e5fe03e6d78 upstream. The sysfs_break_active_protection() routine has an obvious reference leak in its error path. If the call to kernfs_find_and_get() fails then kn will be NULL, so the companion sysfs_unbreak_active_protection() routine won't get called (and would only cause an access violation by trying to dereference kn->parent if it was called). As a result, the reference to kobj acquired at the start of the function will never be released. Fix the leak by adding an explicit kobject_put() call when kn is NULL. Signed-off-by: Alan Stern Fixes: 2afc9166f79b ("scsi: sysfs: Introduce sysfs_{un,}break_active_protection()") Cc: Bart Van Assche Cc: stable@vger.kernel.org Reviewed-by: Bart Van Assche Acked-by: Tejun Heo Link: https://lore.kernel.org/r/8a4d3f0f-c5e3-4b70-a188-0ca433f9e6f9@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman --- fs/sysfs/file.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/sysfs/file.c b/fs/sysfs/file.c index 4f7cf975b27c..b69ce0f68bcb 100644 --- a/fs/sysfs/file.c +++ b/fs/sysfs/file.c @@ -429,6 +429,8 @@ struct kernfs_node *sysfs_break_active_protection(struct kobject *kobj, kn = kernfs_find_and_get(kobj->sd, attr->name); if (kn) kernfs_break_active_protection(kn); + else + kobject_put(kobj); return kn; } EXPORT_SYMBOL_GPL(sysfs_break_active_protection); From 1bc4825d4c3ec6abe43cf06c3c39d664d044cbf7 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 11 Apr 2024 11:15:09 +1000 Subject: [PATCH 049/107] nouveau: fix instmem race condition around ptr stores commit fff1386cc889d8fb4089d285f883f8cba62d82ce upstream. Running a lot of VK CTS in parallel against nouveau, once every few hours you might see something like this crash. BUG: kernel NULL pointer dereference, address: 0000000000000008 PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27 Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021 RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1 RSP: 0000:ffffac20c5857838 EFLAGS: 00010202 RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001 RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180 RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10 R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ... ? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] ? gp100_vmm_pgt_mem+0x37/0x180 [nouveau] nvkm_vmm_iter+0x351/0xa20 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __lock_acquire+0x3ed/0x2170 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_map_locked+0x224/0x3a0 [nouveau] Adding any sort of useful debug usually makes it go away, so I hand wrote the function in a line, and debugged the asm. Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in the nv50_instobj_acquire called from nvkm_kmap. If Thread A and Thread B both get to nv50_instobj_acquire around the same time, and Thread A hits the refcount_set line, and in lockstep thread B succeeds at refcount_inc_not_zero, there is a chance the ptrs value won't have been stored since refcount_set is unordered. Force a memory barrier here, I picked smp_mb, since we want it on all CPUs and it's write followed by a read. v2: use paired smp_rmb/smp_wmb. Cc: Fixes: be55287aa5ba ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj") Signed-off-by: Dave Airlie Signed-off-by: Danilo Krummrich Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c b/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c index 02c4eb28cef4..f3db07325dbd 100644 --- a/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c +++ b/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c @@ -221,8 +221,11 @@ nv50_instobj_acquire(struct nvkm_memory *memory) void __iomem *map = NULL; /* Already mapped? */ - if (refcount_inc_not_zero(&iobj->maps)) + if (refcount_inc_not_zero(&iobj->maps)) { + /* read barrier match the wmb on refcount set */ + smp_rmb(); return iobj->map; + } /* Take the lock, and re-check that another thread hasn't * already mapped the object in the meantime. @@ -249,6 +252,8 @@ nv50_instobj_acquire(struct nvkm_memory *memory) iobj->base.memory.ptrs = &nv50_instobj_fast; else iobj->base.memory.ptrs = &nv50_instobj_slow; + /* barrier to ensure the ptrs are written before refcount is set */ + smp_wmb(); refcount_set(&iobj->maps, 1); } From 90f43980ea6be4ad903e389be9a27a2a0018f1c8 Mon Sep 17 00:00:00 2001 From: Jeongjun Park Date: Tue, 16 Apr 2024 03:20:48 +0900 Subject: [PATCH 050/107] nilfs2: fix OOB in nilfs_set_de_type commit c4a7dc9523b59b3e73fd522c73e95e072f876b16 upstream. The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function, which uses this array, specifies the index to read from the array in the same way as "(mode & S_IFMT) >> S_SHIFT". static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode *inode) { umode_t mode = inode->i_mode; de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob } However, when the index is determined this way, an out-of-bounds (OOB) error occurs by referring to an index that is 1 larger than the array size when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a patch to resize the nilfs_type_by_mode array should be applied to prevent OOB errors. Link: https://lkml.kernel.org/r/20240415182048.7144-1-konishi.ryusuke@gmail.com Reported-by: syzbot+2e22057de05b9f3b30d8@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=2e22057de05b9f3b30d8 Fixes: 2ba466d74ed7 ("nilfs2: directory entry operations") Signed-off-by: Jeongjun Park Signed-off-by: Ryusuke Konishi Tested-by: Ryusuke Konishi Cc: Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- fs/nilfs2/dir.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nilfs2/dir.c b/fs/nilfs2/dir.c index 81394e22d0a0..eb7de9e2a384 100644 --- a/fs/nilfs2/dir.c +++ b/fs/nilfs2/dir.c @@ -243,7 +243,7 @@ nilfs_filetype_table[NILFS_FT_MAX] = { #define S_SHIFT 12 static unsigned char -nilfs_type_by_mode[S_IFMT >> S_SHIFT] = { +nilfs_type_by_mode[(S_IFMT >> S_SHIFT) + 1] = { [S_IFREG >> S_SHIFT] = NILFS_FT_REG_FILE, [S_IFDIR >> S_SHIFT] = NILFS_FT_DIR, [S_IFCHR >> S_SHIFT] = NILFS_FT_CHRDEV, From 7dc6e67f51b52d81c2a899b62de825c0f6baac41 Mon Sep 17 00:00:00 2001 From: Vitaly Kuznetsov Date: Wed, 10 Jun 2020 19:55:31 +0200 Subject: [PATCH 051/107] KVM: async_pf: Cleanup kvm_setup_async_pf() commit 7863e346e1089b40cac1c7d9098314c405e2e1e3 upstream. schedule_work() returns 'false' only when the work is already on the queue and this can't happen as kvm_setup_async_pf() always allocates a new one. Also, to avoid potential race, it makes sense to to schedule_work() at the very end after we've added it to the queue. While on it, do some minor cleanup. gfn_to_pfn_async() mentioned in a comment does not currently exist and, moreover, we can check kvm_is_error_hva() at the very beginning, before we try to allocate work so 'retry_sync' label can go away completely. Signed-off-by: Vitaly Kuznetsov Message-Id: <20200610175532.779793-1-vkuznets@redhat.com> Reviewed-by: Sean Christopherson Signed-off-by: Paolo Bonzini Cc: Guenter Roeck Signed-off-by: Greg Kroah-Hartman --- virt/kvm/async_pf.c | 19 ++++++------------- 1 file changed, 6 insertions(+), 13 deletions(-) diff --git a/virt/kvm/async_pf.c b/virt/kvm/async_pf.c index d0a1113b0e55..9e6532488c47 100644 --- a/virt/kvm/async_pf.c +++ b/virt/kvm/async_pf.c @@ -195,7 +195,9 @@ int kvm_setup_async_pf(struct kvm_vcpu *vcpu, gpa_t cr2_or_gpa, if (vcpu->async_pf.queued >= ASYNC_PF_PER_VCPU) return 0; - /* setup delayed work */ + /* Arch specific code should not do async PF in this case */ + if (unlikely(kvm_is_error_hva(hva))) + return 0; /* * do alloc nowait since if we are going to sleep anyway we @@ -213,24 +215,15 @@ int kvm_setup_async_pf(struct kvm_vcpu *vcpu, gpa_t cr2_or_gpa, work->mm = current->mm; mmget(work->mm); - /* this can't really happen otherwise gfn_to_pfn_async - would succeed */ - if (unlikely(kvm_is_error_hva(work->addr))) - goto retry_sync; - INIT_WORK(&work->work, async_pf_execute); - if (!schedule_work(&work->work)) - goto retry_sync; list_add_tail(&work->queue, &vcpu->async_pf.queue); vcpu->async_pf.queued++; kvm_arch_async_page_not_present(vcpu, work); + + schedule_work(&work->work); + return 1; -retry_sync: - kvm_put_kvm(work->vcpu->kvm); - mmput(work->mm); - kmem_cache_free(async_pf_cache, work); - return 0; } int kvm_async_pf_wakeup_all(struct kvm_vcpu *vcpu) From 2d7d80942e99511a16ed61ef6756858e755816e2 Mon Sep 17 00:00:00 2001 From: Iskander Amara Date: Fri, 8 Mar 2024 09:52:43 +0100 Subject: [PATCH 052/107] arm64: dts: rockchip: fix alphabetical ordering RK3399 puma [ Upstream commit f0abb4b2c7acf3c3e4130dc3f54cd90cf2ae62bc ] Nodes overridden by their reference should be ordered alphabetically to make it easier to read the DTS. pinctrl node is defined in the wrong location so let's reorder it. Signed-off-by: Iskander Amara Reviewed-by: Quentin Schulz Link: https://lore.kernel.org/r/20240308085243.69903-2-iskander.amara@theobroma-systems.com Signed-off-by: Heiko Stuebner Stable-dep-of: 945a7c857091 ("arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma") Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi index 365fa9a3c5bf..ecef3d9b0b93 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi @@ -425,15 +425,6 @@ gpio1830-supply = <&vcc_1v8>; }; -&pmu_io_domains { - status = "okay"; - pmu1830-supply = <&vcc_1v8>; -}; - -&pwm2 { - status = "okay"; -}; - &pinctrl { i2c8 { i2c8_xfer_a: i2c8-xfer { @@ -465,6 +456,15 @@ }; }; +&pmu_io_domains { + status = "okay"; + pmu1830-supply = <&vcc_1v8>; +}; + +&pwm2 { + status = "okay"; +}; + &sdhci { /* * Signal integrity isn't great at 200MHz but 100MHz has proven stable From 55f3e91e917b64f5582f62be3ed16a9454039a9d Mon Sep 17 00:00:00 2001 From: Quentin Schulz Date: Fri, 8 Mar 2024 16:46:08 +0100 Subject: [PATCH 053/107] arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma [ Upstream commit 945a7c8570916650a415757d15d83e0fa856a686 ] The PCIE_WAKE# has a diode used as a level-shifter, and is used as an input pin. While the SoC default is to enable the pull-up, the core rk3399 pinconf for this pin opted for pull-none. So as to not disturb the behaviour of other boards which may rely on pull-none instead of pull-up, set the needed pull-up only for RK3399 Puma. Fixes: 60fd9f72ce8a ("arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM") Signed-off-by: Quentin Schulz Link: https://lore.kernel.org/r/20240308-puma-diode-pu-v2-2-309f83da110a@theobroma-systems.com Signed-off-by: Heiko Stuebner Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi index ecef3d9b0b93..5382c2f0b642 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi @@ -425,6 +425,11 @@ gpio1830-supply = <&vcc_1v8>; }; +&pcie_clkreqn_cpm { + rockchip,pins = + <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>; +}; + &pinctrl { i2c8 { i2c8_xfer_a: i2c8-xfer { From dcc04db701898273e7c7e27bf35890b22a585011 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Sun, 17 Mar 2024 23:10:48 +0100 Subject: [PATCH 054/107] arm64: dts: mediatek: mt7622: fix IR nodename MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 800dc93c3941e372c94278bf4059e6e82f60bd66 ] Fix following validation error: arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: cir@10009000: $nodename:0: 'cir@10009000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$' from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml# Fixes: ae457b7679c4 ("arm64: dts: mt7622: add SoC and peripheral related device nodes") Signed-off-by: Rafał Miłecki Reviewed-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20240317221050.18595-3-zajec5@gmail.com Signed-off-by: AngeloGioacchino Del Regno Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/mediatek/mt7622.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index 3bfe9f5d2a14..7f5ffbd2381f 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -244,7 +244,7 @@ clock-names = "hif_sel"; }; - cir: cir@10009000 { + cir: ir-receiver@10009000 { compatible = "mediatek,mt7622-cir"; reg = <0 0x10009000 0 0x1000>; interrupts = ; From 1e4ce3ba7fa099347879b15a5dd27fd2250a7cb8 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Sun, 17 Mar 2024 23:10:49 +0100 Subject: [PATCH 055/107] arm64: dts: mediatek: mt7622: fix ethernet controller "compatible" MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 208add29ce5b7291f6c466e4dfd9cbf61c72888e ] Fix following validation error: arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: ethernet@1b100000: compatible: ['mediatek,mt7622-eth', 'mediatek,mt2701-eth', 'syscon'] is too long from schema $id: http://devicetree.org/schemas/net/mediatek,net.yaml# (and other complains about wrong clocks). Fixes: 5f599b3a0bb8 ("arm64: dts: mt7622: add ethernet device nodes") Signed-off-by: Rafał Miłecki Reviewed-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20240317221050.18595-4-zajec5@gmail.com Signed-off-by: AngeloGioacchino Del Regno Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/mediatek/mt7622.dtsi | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index 7f5ffbd2381f..aa4593af576c 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -901,9 +901,7 @@ }; eth: ethernet@1b100000 { - compatible = "mediatek,mt7622-eth", - "mediatek,mt2701-eth", - "syscon"; + compatible = "mediatek,mt7622-eth"; reg = <0 0x1b100000 0 0x20000>; interrupts = , , From 73556b21018a0e54b0389ad5402f3701b2386496 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Sun, 17 Mar 2024 23:10:50 +0100 Subject: [PATCH 056/107] arm64: dts: mediatek: mt7622: drop "reset-names" from thermal block MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit ecb5b0034f5bcc35003b4b965cf50c6e98316e79 ] Binding doesn't specify "reset-names" property and Linux driver also doesn't use it. Fix following validation error: arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: thermal@1100b000: Unevaluated properties are not allowed ('reset-names' was unexpected) from schema $id: http://devicetree.org/schemas/thermal/mediatek,thermal.yaml# Fixes: ae457b7679c4 ("arm64: dts: mt7622: add SoC and peripheral related device nodes") Signed-off-by: Rafał Miłecki Reviewed-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20240317221050.18595-5-zajec5@gmail.com Signed-off-by: AngeloGioacchino Del Regno Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/mediatek/mt7622.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index aa4593af576c..122ff44a092e 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -507,7 +507,6 @@ <&pericfg CLK_PERI_AUXADC_PD>; clock-names = "therm", "auxadc"; resets = <&pericfg MT7622_PERI_THERM_SW_RST>; - reset-names = "therm"; mediatek,auxadc = <&auxadc>; mediatek,apmixedsys = <&apmixedsys>; nvmem-cells = <&thermal_calibration>; From 8f70bcc88da013e69b01eb014414c75d104614e1 Mon Sep 17 00:00:00 2001 From: Biao Huang Date: Wed, 9 Oct 2019 15:10:22 +0800 Subject: [PATCH 057/107] arm64: dts: mt2712: add ethernet device node [ Upstream commit e9cabfd046d55d05f11d05fccc4019aa4bad29c6 ] This patch add device node for mt2712 ethernet. Signed-off-by: Biao Huang Signed-off-by: Matthias Brugger Stable-dep-of: 3baac7291eff ("arm64: dts: mediatek: mt2712: fix validation errors") Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 74 +++++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 65 ++++++++++++++++++ 2 files changed, 139 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts index 45e37aa67ce7..9d20cabf4f69 100644 --- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts @@ -105,7 +105,81 @@ proc-supply = <&cpus_fixed_vproc1>; }; +ð { + phy-mode ="rgmii-rxid"; + phy-handle = <ðernet_phy0>; + mediatek,tx-delay-ps = <1530>; + snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <ð_default>; + pinctrl-1 = <ð_sleep>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ethernet_phy0: ethernet-phy@5 { + compatible = "ethernet-phy-id0243.0d90"; + reg = <0x5>; + }; + }; +}; + &pio { + eth_default: eth_default { + tx_pins { + pinmux = , + , + , + , + , + ; + drive-strength = ; + }; + rx_pins { + pinmux = , + , + , + , + , + ; + input-enable; + }; + mdio_pins { + pinmux = , + ; + drive-strength = ; + input-enable; + }; + }; + + eth_sleep: eth_sleep { + tx_pins { + pinmux = , + , + , + , + , + ; + }; + rx_pins { + pinmux = , + , + , + , + , + ; + input-disable; + }; + mdio_pins { + pinmux = , + ; + input-disable; + bias-disable; + }; + }; + usb0_id_pins_float: usb0_iddig { pins_iddig { pinmux = ; diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi index 3b12bb313dcd..4de82e91649f 100644 --- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi @@ -632,6 +632,71 @@ status = "disabled"; }; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <3>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + queue1 { + snps,weight = <0x11>; + snps,dcb-algorithm; + snps,priority = <0x1>; + }; + queue2 { + snps,weight = <0x12>; + snps,dcb-algorithm; + snps,priority = <0x2>; + }; + }; + + eth: ethernet@1101c000 { + compatible = "mediatek,mt2712-gmac"; + reg = <0 0x1101c000 0 0x1300>; + interrupts = ; + interrupt-names = "macirq"; + mac-address = [00 55 7b b5 7d f7]; + clock-names = "axi", + "apb", + "mac_main", + "ptp_ref"; + clocks = <&pericfg CLK_PERI_GMAC>, + <&pericfg CLK_PERI_GMAC_PCLK>, + <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>; + assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, + <&topckgen CLK_TOP_APLL1_D3>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; + mediatek,pericfg = <&pericfg>; + snps,axi-config = <&stmmac_axi_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + snps,txpbl = <1>; + snps,rxpbl = <1>; + clk_csr = <0>; + status = "disabled"; + }; + mmc0: mmc@11230000 { compatible = "mediatek,mt2712-mmc"; reg = <0 0x11230000 0 0x1000>; From 8378341b215f8b6544292eacd28fe15066b57264 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Fri, 1 Mar 2024 08:47:41 +0100 Subject: [PATCH 058/107] arm64: dts: mediatek: mt2712: fix validation errors MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 3baac7291effb501c4d52df7019ebf52011e5772 ] 1. Fixup infracfg clock controller binding It also acts as reset controller so #reset-cells is required. 2. Use -pins suffix for pinctrl This fixes: arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: syscon@10001000: '#reset-cells' is a required property from schema $id: http://devicetree.org/schemas/arm/mediatek/mediatek,infracfg.yaml# arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: pinctrl@1000b000: 'eth_default', 'eth_sleep', 'usb0_iddig', 'usb1_iddig' do not match any of the regexes: 'pinctrl-[0-9]+', 'pins$' from schema $id: http://devicetree.org/schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml# Signed-off-by: Rafał Miłecki Reviewed-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20240301074741.8362-1-zajec5@gmail.com [Angelo: Added Fixes tags] Fixes: 5d4839709c8e ("arm64: dts: mt2712: Add clock controller device nodes") Fixes: 1724f4cc5133 ("arm64: dts: Add USB3 related nodes for MT2712") Signed-off-by: AngeloGioacchino Del Regno Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 8 ++++---- arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 3 ++- 2 files changed, 6 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts index 9d20cabf4f69..99515c13da3c 100644 --- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts @@ -127,7 +127,7 @@ }; &pio { - eth_default: eth_default { + eth_default: eth-default-pins { tx_pins { pinmux = , , @@ -154,7 +154,7 @@ }; }; - eth_sleep: eth_sleep { + eth_sleep: eth-sleep-pins { tx_pins { pinmux = , , @@ -180,14 +180,14 @@ }; }; - usb0_id_pins_float: usb0_iddig { + usb0_id_pins_float: usb0-iddig-pins { pins_iddig { pinmux = ; bias-pull-up; }; }; - usb1_id_pins_float: usb1_iddig { + usb1_id_pins_float: usb1-iddig-pins { pins_iddig { pinmux = ; bias-pull-up; diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi index 4de82e91649f..2c20a1be0699 100644 --- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi @@ -249,10 +249,11 @@ #clock-cells = <1>; }; - infracfg: syscon@10001000 { + infracfg: clock-controller@10001000 { compatible = "mediatek,mt2712-infracfg", "syscon"; reg = <0 0x10001000 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; pericfg: syscon@10003000 { From ef3c87d5409913624d9e741635088f43ff463486 Mon Sep 17 00:00:00 2001 From: Alexey Brodkin Date: Fri, 29 Mar 2024 10:36:50 +0000 Subject: [PATCH 059/107] ARC: [plat-hsdk]: Remove misplaced interrupt-cells property [ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ] "gmac" node stands for just an ordinary Ethernet controller, which is by no means a provider of interrupts, i.e. it doesn't serve as an interrupt controller, thus "#interrupt-cells" property doesn't belong to it and so we remove it. Fixes: ------------>8------------ DTC arch/arc/boot/dts/hsdk.dtb arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider' ------------>8------------ Reported-by: Vineet Gupta Signed-off-by: Alexey Brodkin Signed-off-by: Vineet Gupta Signed-off-by: Sasha Levin --- arch/arc/boot/dts/hsdk.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arc/boot/dts/hsdk.dts b/arch/arc/boot/dts/hsdk.dts index dcaa44e408ac..27f4194b376b 100644 --- a/arch/arc/boot/dts/hsdk.dts +++ b/arch/arc/boot/dts/hsdk.dts @@ -205,7 +205,6 @@ }; gmac: ethernet@8000 { - #interrupt-cells = <1>; compatible = "snps,dwmac"; reg = <0x8000 0x2000>; interrupts = <10>; From 51cf144f9cfa97b62708b4643cf7107ddf9513b6 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Thu, 18 Apr 2024 15:29:08 +0200 Subject: [PATCH 060/107] vxlan: drop packets from invalid src-address [ Upstream commit f58f45c1e5b92975e91754f5407250085a6ae7cf ] The VXLAN driver currently does not check if the inner layer2 source-address is valid. In case source-address snooping/learning is enabled, a entry in the FDB for the invalid address is created with the layer3 address of the tunnel endpoint. If the frame happens to have a non-unicast address set, all this non-unicast traffic is subsequently not flooded to the tunnel network but sent to the learnt host in the FDB. To make matters worse, this FDB entry does not expire. Apply the same filtering for packets as it is done for bridges. This not only drops these invalid packets but avoids them from being learnt into the FDB. Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Suggested-by: Ido Schimmel Signed-off-by: David Bauer Signed-off-by: David S. Miller Signed-off-by: Sasha Levin --- drivers/net/vxlan.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/vxlan.c b/drivers/net/vxlan.c index 8808a6540b19..f70500c85e2a 100644 --- a/drivers/net/vxlan.c +++ b/drivers/net/vxlan.c @@ -1605,6 +1605,10 @@ static bool vxlan_set_mac(struct vxlan_dev *vxlan, if (ether_addr_equal(eth_hdr(skb)->h_source, vxlan->dev->dev_addr)) return false; + /* Ignore packets from invalid src-address */ + if (!is_valid_ether_addr(eth_hdr(skb)->h_source)) + return false; + /* Get address from the outer IP header */ if (vxlan_get_sk_family(vs) == AF_INET) { saddr.sin.sin_addr.s_addr = ip_hdr(skb)->saddr; From 42de7aa3916a574467ffcc67450d39dcf7674c77 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Thu, 18 Apr 2024 15:46:06 +0200 Subject: [PATCH 061/107] mlxsw: core: Unregister EMAD trap using FORWARD action [ Upstream commit 976c44af48141cd8595601c0af2a19a43c5b228b ] The device's manual (PRM - Programmer's Reference Manual) classifies the trap that is used to deliver EMAD responses as an "event trap". Among other things, it means that the only actions that can be associated with the trap are TRAP and FORWARD (NOP). Currently, during driver de-initialization the driver unregisters the trap by setting its action to DISCARD, which violates the above guideline. Future firmware versions will prevent such misuses by returning an error. This does not prevent the driver from working, but an error will be printed to the kernel log during module removal / devlink reload: mlxsw_spectrum 0000:03:00.0: Reg cmd access status failed (status=7(bad parameter)) mlxsw_spectrum 0000:03:00.0: Reg cmd access failed (reg_id=7003(hpkt),type=write) Suppress the error message by aligning the driver to the manual and use a FORWARD (NOP) action when unregistering the trap. Fixes: 4ec14b7634b2 ("mlxsw: Add interface to access registers and process events") Cc: Jiri Pirko Cc: Amit Cohen Signed-off-by: Ido Schimmel Reviewed-by: Petr Machata Reviewed-by: Simon Horman Signed-off-by: Petr Machata Link: https://lore.kernel.org/r/753a89e14008fde08cb4a2c1e5f537b81d8eb2d6.1713446092.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/core.c b/drivers/net/ethernet/mellanox/mlxsw/core.c index 2d39bade89e3..bb9299481b45 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/core.c +++ b/drivers/net/ethernet/mellanox/mlxsw/core.c @@ -566,7 +566,7 @@ free_skb: static const struct mlxsw_listener mlxsw_emad_rx_listener = MLXSW_RXL(mlxsw_emad_rx_listener_func, ETHEMAD, TRAP_TO_CPU, false, - EMAD, DISCARD); + EMAD, FORWARD); static int mlxsw_emad_init(struct mlxsw_core *mlxsw_core) { From 380bf477520f5c5ff4b3048ca32fa18d98cf20a2 Mon Sep 17 00:00:00 2001 From: Paul Geurts Date: Thu, 18 Apr 2024 21:25:38 +0200 Subject: [PATCH 062/107] NFC: trf7970a: disable all regulators on removal [ Upstream commit 6bea4f03c6a4e973ef369e15aac88f37981db49e ] During module probe, regulator 'vin' and 'vdd-io' are used and enabled, but the vdd-io regulator overwrites the 'vin' regulator pointer. During remove, only the vdd-io is disabled, as the vin regulator pointer is not available anymore. When regulator_put() is called during resource cleanup a kernel warning is given, as the regulator is still enabled. Store the two regulators in separate pointers and disable both the regulators on module remove. Fixes: 49d22c70aaf0 ("NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage") Signed-off-by: Paul Geurts Reviewed-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/DB7PR09MB26847A4EBF88D9EDFEB1DA0F950E2@DB7PR09MB2684.eurprd09.prod.outlook.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/nfc/trf7970a.c | 42 +++++++++++++++++++++++------------------- 1 file changed, 23 insertions(+), 19 deletions(-) diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c index e46adaac1c63..153ed0c0c2b1 100644 --- a/drivers/nfc/trf7970a.c +++ b/drivers/nfc/trf7970a.c @@ -424,7 +424,8 @@ struct trf7970a { enum trf7970a_state state; struct device *dev; struct spi_device *spi; - struct regulator *regulator; + struct regulator *vin_regulator; + struct regulator *vddio_regulator; struct nfc_digital_dev *ddev; u32 quirks; bool is_initiator; @@ -1883,7 +1884,7 @@ static int trf7970a_power_up(struct trf7970a *trf) if (trf->state != TRF7970A_ST_PWR_OFF) return 0; - ret = regulator_enable(trf->regulator); + ret = regulator_enable(trf->vin_regulator); if (ret) { dev_err(trf->dev, "%s - Can't enable VIN: %d\n", __func__, ret); return ret; @@ -1926,7 +1927,7 @@ static int trf7970a_power_down(struct trf7970a *trf) if (trf->en2_gpiod && !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW)) gpiod_set_value_cansleep(trf->en2_gpiod, 0); - ret = regulator_disable(trf->regulator); + ret = regulator_disable(trf->vin_regulator); if (ret) dev_err(trf->dev, "%s - Can't disable VIN: %d\n", __func__, ret); @@ -2065,37 +2066,37 @@ static int trf7970a_probe(struct spi_device *spi) mutex_init(&trf->lock); INIT_DELAYED_WORK(&trf->timeout_work, trf7970a_timeout_work_handler); - trf->regulator = devm_regulator_get(&spi->dev, "vin"); - if (IS_ERR(trf->regulator)) { - ret = PTR_ERR(trf->regulator); + trf->vin_regulator = devm_regulator_get(&spi->dev, "vin"); + if (IS_ERR(trf->vin_regulator)) { + ret = PTR_ERR(trf->vin_regulator); dev_err(trf->dev, "Can't get VIN regulator: %d\n", ret); goto err_destroy_lock; } - ret = regulator_enable(trf->regulator); + ret = regulator_enable(trf->vin_regulator); if (ret) { dev_err(trf->dev, "Can't enable VIN: %d\n", ret); goto err_destroy_lock; } - uvolts = regulator_get_voltage(trf->regulator); + uvolts = regulator_get_voltage(trf->vin_regulator); if (uvolts > 4000000) trf->chip_status_ctrl = TRF7970A_CHIP_STATUS_VRS5_3; - trf->regulator = devm_regulator_get(&spi->dev, "vdd-io"); - if (IS_ERR(trf->regulator)) { - ret = PTR_ERR(trf->regulator); + trf->vddio_regulator = devm_regulator_get(&spi->dev, "vdd-io"); + if (IS_ERR(trf->vddio_regulator)) { + ret = PTR_ERR(trf->vddio_regulator); dev_err(trf->dev, "Can't get VDD_IO regulator: %d\n", ret); - goto err_destroy_lock; + goto err_disable_vin_regulator; } - ret = regulator_enable(trf->regulator); + ret = regulator_enable(trf->vddio_regulator); if (ret) { dev_err(trf->dev, "Can't enable VDD_IO: %d\n", ret); - goto err_destroy_lock; + goto err_disable_vin_regulator; } - if (regulator_get_voltage(trf->regulator) == 1800000) { + if (regulator_get_voltage(trf->vddio_regulator) == 1800000) { trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW; dev_dbg(trf->dev, "trf7970a config vdd_io to 1.8V\n"); } @@ -2108,7 +2109,7 @@ static int trf7970a_probe(struct spi_device *spi) if (!trf->ddev) { dev_err(trf->dev, "Can't allocate NFC digital device\n"); ret = -ENOMEM; - goto err_disable_regulator; + goto err_disable_vddio_regulator; } nfc_digital_set_parent_dev(trf->ddev, trf->dev); @@ -2137,8 +2138,10 @@ err_shutdown: trf7970a_shutdown(trf); err_free_ddev: nfc_digital_free_device(trf->ddev); -err_disable_regulator: - regulator_disable(trf->regulator); +err_disable_vddio_regulator: + regulator_disable(trf->vddio_regulator); +err_disable_vin_regulator: + regulator_disable(trf->vin_regulator); err_destroy_lock: mutex_destroy(&trf->lock); return ret; @@ -2157,7 +2160,8 @@ static int trf7970a_remove(struct spi_device *spi) nfc_digital_unregister_device(trf->ddev); nfc_digital_free_device(trf->ddev); - regulator_disable(trf->regulator); + regulator_disable(trf->vddio_regulator); + regulator_disable(trf->vin_regulator); mutex_destroy(&trf->lock); From b51177e40ea79a3ebddf6b6c9cd4fe77ec63bcbe Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sun, 21 Apr 2024 19:38:28 +0000 Subject: [PATCH 063/107] net: usb: ax88179_178a: stop lying about skb->truesize [ Upstream commit 4ce62d5b2f7aecd4900e7d6115588ad7f9acccca ] Some usb drivers try to set small skb->truesize and break core networking stacks. In this patch, I removed one of the skb->truesize overide. I also replaced one skb_clone() by an allocation of a fresh and small skb, to get minimally sized skbs, like we did in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize in rx path") Fixes: f8ebb3ac881b ("net: usb: ax88179_178a: Fix packet receiving") Reported-by: shironeko Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/ Signed-off-by: Eric Dumazet Cc: Jose Alonso Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/usb/ax88179_178a.c | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-) diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c index 84dc9fb2b1f3..c6159b521e06 100644 --- a/drivers/net/usb/ax88179_178a.c +++ b/drivers/net/usb/ax88179_178a.c @@ -1452,21 +1452,16 @@ static int ax88179_rx_fixup(struct usbnet *dev, struct sk_buff *skb) /* Skip IP alignment pseudo header */ skb_pull(skb, 2); - skb->truesize = SKB_TRUESIZE(pkt_len_plus_padd); ax88179_rx_checksum(skb, pkt_hdr); return 1; } - ax_skb = skb_clone(skb, GFP_ATOMIC); + ax_skb = netdev_alloc_skb_ip_align(dev->net, pkt_len); if (!ax_skb) return 0; - skb_trim(ax_skb, pkt_len); + skb_put(ax_skb, pkt_len); + memcpy(ax_skb->data, skb->data + 2, pkt_len); - /* Skip IP alignment pseudo header */ - skb_pull(ax_skb, 2); - - skb->truesize = pkt_len_plus_padd + - SKB_DATA_ALIGN(sizeof(struct sk_buff)); ax88179_rx_checksum(ax_skb, pkt_hdr); usbnet_skb_return(dev, ax_skb); From 718df1bc226c383dd803397d7f5d95557eb81ac7 Mon Sep 17 00:00:00 2001 From: Hyunwoo Kim Date: Mon, 22 Apr 2024 05:39:30 -0400 Subject: [PATCH 064/107] net: gtp: Fix Use-After-Free in gtp_dellink [ Upstream commit f2a904107ee2b647bb7794a1a82b67740d7c8a64 ] Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal of gtp_dellink, is not part of the RCU read critical section, it is possible that the RCU grace period will pass during the traversal and the key will be free. To prevent this, it should be changed to hlist_for_each_entry_safe. Fixes: 94dc550a5062 ("gtp: fix an use-after-free in ipv4_pdp_find()") Signed-off-by: Hyunwoo Kim Reviewed-by: Eric Dumazet Signed-off-by: David S. Miller Signed-off-by: Sasha Levin --- drivers/net/gtp.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c index e5961082a4af..0d6d2fe9eabd 100644 --- a/drivers/net/gtp.c +++ b/drivers/net/gtp.c @@ -706,11 +706,12 @@ out_hashtable: static void gtp_dellink(struct net_device *dev, struct list_head *head) { struct gtp_dev *gtp = netdev_priv(dev); + struct hlist_node *next; struct pdp_ctx *pctx; int i; for (i = 0; i < gtp->hash_size; i++) - hlist_for_each_entry_rcu(pctx, >p->tid_hash[i], hlist_tid) + hlist_for_each_entry_safe(pctx, next, >p->tid_hash[i], hlist_tid) pdp_context_delete(pctx); list_del_rcu(>p->list); From 3606e77b546ba0c1771527c56477b46f306177a9 Mon Sep 17 00:00:00 2001 From: Ismael Luceno Date: Sun, 21 Apr 2024 16:22:32 +0200 Subject: [PATCH 065/107] ipvs: Fix checksumming on GSO of SCTP packets [ Upstream commit e10d3ba4d434ed172914617ed8d74bd411421193 ] It was observed in the wild that pairs of consecutive packets would leave the IPVS with the same wrong checksum, and the issue only went away when disabling GSO. IPVS needs to avoid computing the SCTP checksum when using GSO. Fixes: 90017accff61 ("sctp: Add GSO support") Co-developed-by: Firo Yang Signed-off-by: Ismael Luceno Tested-by: Andreas Taschner Acked-by: Julian Anastasov Signed-off-by: Pablo Neira Ayuso Signed-off-by: Sasha Levin --- net/netfilter/ipvs/ip_vs_proto_sctp.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/net/netfilter/ipvs/ip_vs_proto_sctp.c b/net/netfilter/ipvs/ip_vs_proto_sctp.c index a0921adc31a9..1e689c714127 100644 --- a/net/netfilter/ipvs/ip_vs_proto_sctp.c +++ b/net/netfilter/ipvs/ip_vs_proto_sctp.c @@ -126,7 +126,8 @@ sctp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp, if (sctph->source != cp->vport || payload_csum || skb->ip_summed == CHECKSUM_PARTIAL) { sctph->source = cp->vport; - sctp_nat_csum(skb, sctph, sctphoff); + if (!skb_is_gso(skb) || !skb_is_gso_sctp(skb)) + sctp_nat_csum(skb, sctph, sctphoff); } else { skb->ip_summed = CHECKSUM_UNNECESSARY; } @@ -174,7 +175,8 @@ sctp_dnat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp, (skb->ip_summed == CHECKSUM_PARTIAL && !(skb_dst(skb)->dev->features & NETIF_F_SCTP_CRC))) { sctph->dest = cp->dport; - sctp_nat_csum(skb, sctph, sctphoff); + if (!skb_is_gso(skb) || !skb_is_gso_sctp(skb)) + sctp_nat_csum(skb, sctph, sctphoff); } else if (skb->ip_summed != CHECKSUM_PARTIAL) { skb->ip_summed = CHECKSUM_UNNECESSARY; } From 589523cf0b384164e445dd5db8d5b1bf97982424 Mon Sep 17 00:00:00 2001 From: Hyunwoo Kim Date: Mon, 22 Apr 2024 05:37:17 -0400 Subject: [PATCH 066/107] net: openvswitch: Fix Use-After-Free in ovs_ct_exit [ Upstream commit 5ea7b72d4fac2fdbc0425cd8f2ea33abe95235b2 ] Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal of ovs_ct_limit_exit, is not part of the RCU read critical section, it is possible that the RCU grace period will pass during the traversal and the key will be free. To prevent this, it should be changed to hlist_for_each_entry_safe. Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit") Signed-off-by: Hyunwoo Kim Reviewed-by: Eric Dumazet Reviewed-by: Aaron Conole Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- net/openvswitch/conntrack.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/openvswitch/conntrack.c b/net/openvswitch/conntrack.c index 90c5f5300728..48522c688c3e 100644 --- a/net/openvswitch/conntrack.c +++ b/net/openvswitch/conntrack.c @@ -1897,9 +1897,9 @@ static void ovs_ct_limit_exit(struct net *net, struct ovs_net *ovs_net) for (i = 0; i < CT_LIMIT_HASH_BUCKETS; ++i) { struct hlist_head *head = &info->limits[i]; struct ovs_ct_limit *ct_limit; + struct hlist_node *next; - hlist_for_each_entry_rcu(ct_limit, head, hlist_node, - lockdep_ovsl_is_held()) + hlist_for_each_entry_safe(ct_limit, next, head, hlist_node) kfree_rcu(ct_limit, rcu); } kfree(ovs_net->ct_limit_info->limits); From 40bdd69f744aadd392b9eae2fd518ebaa016d6bd Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:25:55 +0200 Subject: [PATCH 067/107] mlxsw: spectrum_acl_tcam: Fix race during rehash delayed work [ Upstream commit d90cfe20562407d9f080d24123078d666d730707 ] The purpose of the rehash delayed work is to reduce the number of masks (eRPs) used by an ACL region as the eRP bank is a global and limited resource. This is done in three steps: 1. Creating a new set of masks and a new ACL region which will use the new masks and to which the existing filters will be migrated to. The new region is assigned to 'vregion->region' and the region from which the filters are migrated from is assigned to 'vregion->region2'. 2. Migrating all the filters from the old region to the new region. 3. Destroying the old region and setting 'vregion->region2' to NULL. Only the second steps is performed under the 'vregion->lock' mutex although its comments says that among other things it "Protects consistency of region, region2 pointers". This is problematic as the first step can race with filter insertion from user space that uses 'vregion->region', but under the mutex. Fix by holding the mutex across the entirety of the delayed work and not only during the second step. Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index ec0d5a4a60a9..5c0ff3d612e3 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -756,7 +756,9 @@ static void mlxsw_sp_acl_tcam_vregion_rehash_work(struct work_struct *work) rehash.dw.work); int credits = MLXSW_SP_ACL_TCAM_VREGION_REHASH_CREDITS; + mutex_lock(&vregion->lock); mlxsw_sp_acl_tcam_vregion_rehash(vregion->mlxsw_sp, vregion, &credits); + mutex_unlock(&vregion->lock); if (credits < 0) /* Rehash gone out of credits so it was interrupted. * Schedule the work as soon as possible to continue. @@ -1394,7 +1396,6 @@ mlxsw_sp_acl_tcam_vregion_migrate(struct mlxsw_sp *mlxsw_sp, int err, err2; trace_mlxsw_sp_acl_tcam_vregion_migrate(mlxsw_sp, vregion); - mutex_lock(&vregion->lock); err = mlxsw_sp_acl_tcam_vchunk_migrate_all(mlxsw_sp, vregion, ctx, credits); if (err) { @@ -1414,7 +1415,6 @@ mlxsw_sp_acl_tcam_vregion_migrate(struct mlxsw_sp *mlxsw_sp, /* Let the rollback to be continued later on. */ } } - mutex_unlock(&vregion->lock); trace_mlxsw_sp_acl_tcam_vregion_migrate_end(mlxsw_sp, vregion); return err; } From 1b73f6e4ea770410a937a8db98f77e52594d23a0 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:25:56 +0200 Subject: [PATCH 068/107] mlxsw: spectrum_acl_tcam: Fix possible use-after-free during activity update [ Upstream commit 79b5b4b18bc85b19d3a518483f9abbbe6d7b3ba4 ] The rule activity update delayed work periodically traverses the list of configured rules and queries their activity from the device. As part of this task it accesses the entry pointed by 'ventry->entry', but this entry can be changed concurrently by the rehash delayed work, leading to a use-after-free [1]. Fix by closing the race and perform the activity query under the 'vregion->lock' mutex. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140 Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181 CPU: 0 PID: 181 Comm: kworker/0:18 Not tainted 6.9.0-rc2-custom-00781-gd5ab772d32f7 #2 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work Call Trace: dump_stack_lvl+0xc6/0x120 print_report+0xce/0x670 kasan_report+0xd7/0x110 mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140 mlxsw_sp_acl_rule_activity_update_work+0x219/0x400 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Allocated by task 1039: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 __kmalloc+0x19c/0x360 mlxsw_sp_acl_tcam_entry_create+0x7b/0x1f0 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x30d/0xb50 mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Freed by task 1039: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 poison_slab_object+0x102/0x170 __kasan_slab_free+0x14/0x30 kfree+0xc1/0x290 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3d7/0xb50 mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/1fcce0a60b231ebeb2515d91022284ba7b4ffe7a.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- .../net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 5c0ff3d612e3..7cd3338ed474 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -1230,8 +1230,14 @@ mlxsw_sp_acl_tcam_ventry_activity_get(struct mlxsw_sp *mlxsw_sp, struct mlxsw_sp_acl_tcam_ventry *ventry, bool *activity) { - return mlxsw_sp_acl_tcam_entry_activity_get(mlxsw_sp, - ventry->entry, activity); + struct mlxsw_sp_acl_tcam_vregion *vregion = ventry->vchunk->vregion; + int err; + + mutex_lock(&vregion->lock); + err = mlxsw_sp_acl_tcam_entry_activity_get(mlxsw_sp, ventry->entry, + activity); + mutex_unlock(&vregion->lock); + return err; } static int From e118e7ea24d1392878ef85926627c6bc640c4388 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:25:57 +0200 Subject: [PATCH 069/107] mlxsw: spectrum_acl_tcam: Fix possible use-after-free during rehash [ Upstream commit 54225988889931467a9b55fdbef534079b665519 ] The rehash delayed work migrates filters from one region to another according to the number of available credits. The migrated from region is destroyed at the end of the work if the number of credits is non-negative as the assumption is that this is indicative of migration being complete. This assumption is incorrect as a non-negative number of credits can also be the result of a failed migration. The destruction of a region that still has filters referencing it can result in a use-after-free [1]. Fix by not destroying the region if migration failed. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230 Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858 CPU: 0 PID: 3858 Comm: kworker/0:31 Tainted: G W 6.9.0-rc2-custom-00782-gf2275c2157d8 #5 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work Call Trace: dump_stack_lvl+0xc6/0x120 print_report+0xce/0x670 kasan_report+0xd7/0x110 mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230 mlxsw_sp_acl_ctcam_entry_del+0x2e/0x70 mlxsw_sp_acl_atcam_entry_del+0x81/0x210 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3cd/0xb50 mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Allocated by task 174: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 __kmalloc+0x19c/0x360 mlxsw_sp_acl_tcam_region_create+0xdf/0x9c0 mlxsw_sp_acl_tcam_vregion_rehash_work+0x954/0x1300 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Freed by task 7: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 poison_slab_object+0x102/0x170 __kasan_slab_free+0x14/0x30 kfree+0xc1/0x290 mlxsw_sp_acl_tcam_region_destroy+0x272/0x310 mlxsw_sp_acl_tcam_vregion_rehash_work+0x731/0x1300 process_one_work+0x8eb/0x19b0 worker_thread+0x6c9/0xf70 kthread+0x2c9/0x3b0 ret_from_fork+0x4d/0x80 ret_from_fork_asm+0x1a/0x30 Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/3e412b5659ec2310c5c615760dfe5eac18dd7ebd.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 7cd3338ed474..7e5dc664c55c 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -1522,6 +1522,7 @@ mlxsw_sp_acl_tcam_vregion_rehash(struct mlxsw_sp *mlxsw_sp, ctx, credits); if (err) { dev_err(mlxsw_sp->bus_info->dev, "Failed to migrate vregion\n"); + return; } if (*credits >= 0) From a43a0423e49e2d0e93b3e823005e8dae2da87330 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:25:58 +0200 Subject: [PATCH 070/107] mlxsw: spectrum_acl_tcam: Rate limit error message [ Upstream commit 5bcf925587e9b5d36420d572a0b4d131c90fb306 ] In the rare cases when the device resources are exhausted it is likely that the rehash delayed work will fail. An error message will be printed whenever this happens which can be overwhelming considering the fact that the work is per-region and that there can be hundreds of regions. Fix by rate limiting the error message. Fixes: e5e7962ee5c2 ("mlxsw: spectrum_acl: Implement region migration according to hints") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 7e5dc664c55c..5175ed6cdae0 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -1521,7 +1521,7 @@ mlxsw_sp_acl_tcam_vregion_rehash(struct mlxsw_sp *mlxsw_sp, err = mlxsw_sp_acl_tcam_vregion_migrate(mlxsw_sp, vregion, ctx, credits); if (err) { - dev_err(mlxsw_sp->bus_info->dev, "Failed to migrate vregion\n"); + dev_err_ratelimited(mlxsw_sp->bus_info->dev, "Failed to migrate vregion\n"); return; } From c6f3fa7f5a748bf6e5c4eb742686d6952f854e76 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:25:59 +0200 Subject: [PATCH 071/107] mlxsw: spectrum_acl_tcam: Fix memory leak during rehash [ Upstream commit 8ca3f7a7b61393804c46f170743c3b839df13977 ] The rehash delayed work migrates filters from one region to another. This is done by iterating over all chunks (all the filters with the same priority) in the region and in each chunk iterating over all the filters. If the migration fails, the code tries to migrate the filters back to the old region. However, the rollback itself can also fail in which case another migration will be erroneously performed. Besides the fact that this ping pong is not a very good idea, it also creates a problem. Each virtual chunk references two chunks: The currently used one ('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the first holds the chunk we want to migrate filters to and the second holds the chunk we are migrating filters from. The code currently assumes - but does not verify - that the backup chunk does not exist (NULL) if the currently used chunk does not reference the target region. This assumption breaks when we are trying to rollback a rollback, resulting in the backup chunk being overwritten and leaked [1]. Fix by not rolling back a failed rollback and add a warning to avoid future cases. [1] WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20 Modules linked in: CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:parman_destroy+0x17/0x20 [...] Call Trace: mlxsw_sp_acl_atcam_region_fini+0x19/0x60 mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0 mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470 process_one_work+0x151/0x370 worker_thread+0x2cb/0x3e0 kthread+0xd0/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 Fixes: 843500518509 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 5175ed6cdae0..abfa4b44f468 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -1271,6 +1271,8 @@ mlxsw_sp_acl_tcam_vchunk_migrate_start(struct mlxsw_sp *mlxsw_sp, { struct mlxsw_sp_acl_tcam_chunk *new_chunk; + WARN_ON(vchunk->chunk2); + new_chunk = mlxsw_sp_acl_tcam_chunk_create(mlxsw_sp, vchunk, region); if (IS_ERR(new_chunk)) return PTR_ERR(new_chunk); @@ -1405,6 +1407,8 @@ mlxsw_sp_acl_tcam_vregion_migrate(struct mlxsw_sp *mlxsw_sp, err = mlxsw_sp_acl_tcam_vchunk_migrate_all(mlxsw_sp, vregion, ctx, credits); if (err) { + if (ctx->this_is_rollback) + return err; /* In case migration was not successful, we need to swap * so the original region pointer is assigned again * to vregion->region. From 0b88631855026b55cad901ac28d081e0f358e596 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:26:00 +0200 Subject: [PATCH 072/107] mlxsw: spectrum_acl_tcam: Fix warning during rehash [ Upstream commit 743edc8547a92b6192aa1f1b6bb78233fa21dc9b ] As previously explained, the rehash delayed work migrates filters from one region to another. This is done by iterating over all chunks (all the filters with the same priority) in the region and in each chunk iterating over all the filters. When the work runs out of credits it stores the current chunk and entry as markers in the per-work context so that it would know where to resume the migration from the next time the work is scheduled. Upon error, the chunk marker is reset to NULL, but without resetting the entry markers despite being relative to it. This can result in migration being resumed from an entry that does not belong to the chunk being migrated. In turn, this will eventually lead to a chunk being iterated over as if it is an entry. Because of how the two structures happen to be defined, this does not lead to KASAN splats, but to warnings such as [1]. Fix by creating a helper that resets all the markers and call it from all the places the currently only reset the chunk marker. For good measures also call it when starting a completely new rehash. Add a warning to avoid future cases. [1] WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0 Modules linked in: CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:mlxsw_afk_encode+0x242/0x2f0 [...] Call Trace: mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290 mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470 process_one_work+0x151/0x370 worker_thread+0x2cb/0x3e0 kthread+0xd0/0x100 ret_from_fork+0x34/0x50 Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- .../mellanox/mlxsw/spectrum_acl_tcam.c | 20 ++++++++++++++++--- 1 file changed, 17 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index abfa4b44f468..26042c859cf6 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -768,6 +768,17 @@ static void mlxsw_sp_acl_tcam_vregion_rehash_work(struct work_struct *work) mlxsw_sp_acl_tcam_vregion_rehash_work_schedule(vregion); } +static void +mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(struct mlxsw_sp_acl_tcam_rehash_ctx *ctx) +{ + /* The entry markers are relative to the current chunk and therefore + * needs to be reset together with the chunk marker. + */ + ctx->current_vchunk = NULL; + ctx->start_ventry = NULL; + ctx->stop_ventry = NULL; +} + static void mlxsw_sp_acl_tcam_rehash_ctx_vchunk_changed(struct mlxsw_sp_acl_tcam_vchunk *vchunk) { @@ -790,7 +801,7 @@ mlxsw_sp_acl_tcam_rehash_ctx_vregion_changed(struct mlxsw_sp_acl_tcam_vregion *v * the current chunk pointer to make sure all chunks * are properly migrated. */ - vregion->rehash.ctx.current_vchunk = NULL; + mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(&vregion->rehash.ctx); } static struct mlxsw_sp_acl_tcam_vregion * @@ -1291,7 +1302,7 @@ mlxsw_sp_acl_tcam_vchunk_migrate_end(struct mlxsw_sp *mlxsw_sp, { mlxsw_sp_acl_tcam_chunk_destroy(mlxsw_sp, vchunk->chunk2); vchunk->chunk2 = NULL; - ctx->current_vchunk = NULL; + mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx); } static int @@ -1323,6 +1334,8 @@ mlxsw_sp_acl_tcam_vchunk_migrate_one(struct mlxsw_sp *mlxsw_sp, ventry = list_first_entry(&vchunk->ventry_list, typeof(*ventry), list); + WARN_ON(ventry->vchunk != vchunk); + list_for_each_entry_from(ventry, &vchunk->ventry_list, list) { /* During rollback, once we reach the ventry that failed * to migrate, we are done. @@ -1414,7 +1427,7 @@ mlxsw_sp_acl_tcam_vregion_migrate(struct mlxsw_sp *mlxsw_sp, * to vregion->region. */ swap(vregion->region, vregion->region2); - ctx->current_vchunk = NULL; + mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx); ctx->this_is_rollback = true; err2 = mlxsw_sp_acl_tcam_vchunk_migrate_all(mlxsw_sp, vregion, ctx, credits); @@ -1473,6 +1486,7 @@ mlxsw_sp_acl_tcam_vregion_rehash_start(struct mlxsw_sp *mlxsw_sp, ctx->hints_priv = hints_priv; ctx->this_is_rollback = false; + mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx); return 0; From 0b2c13b670b168e324e1cf109e67056a20fd610a Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:26:01 +0200 Subject: [PATCH 073/107] mlxsw: spectrum_acl_tcam: Fix incorrect list API usage [ Upstream commit b377add0f0117409c418ddd6504bd682ebe0bf79 ] Both the function that migrates all the chunks within a region and the function that migrates all the entries within a chunk call list_first_entry() on the respective lists without checking that the lists are not empty. This is incorrect usage of the API, which leads to the following warning [1]. Fix by returning if the lists are empty as there is nothing to migrate in this case. [1] WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0> Modules linked in: CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0 [...] Call Trace: mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0 process_one_work+0x151/0x370 worker_thread+0x2cb/0x3e0 kthread+0xd0/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Reviewed-by: Petr Machata Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 26042c859cf6..89ce9b1233bd 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -1325,6 +1325,9 @@ mlxsw_sp_acl_tcam_vchunk_migrate_one(struct mlxsw_sp *mlxsw_sp, return 0; } + if (list_empty(&vchunk->ventry_list)) + goto out; + /* If the migration got interrupted, we have the ventry to start from * stored in context. */ @@ -1376,6 +1379,7 @@ mlxsw_sp_acl_tcam_vchunk_migrate_one(struct mlxsw_sp *mlxsw_sp, } } +out: mlxsw_sp_acl_tcam_vchunk_migrate_end(mlxsw_sp, vchunk, ctx); return 0; } @@ -1389,6 +1393,9 @@ mlxsw_sp_acl_tcam_vchunk_migrate_all(struct mlxsw_sp *mlxsw_sp, struct mlxsw_sp_acl_tcam_vchunk *vchunk; int err; + if (list_empty(&vregion->vchunk_list)) + return 0; + /* If the migration got interrupted, we have the vchunk * we are working on stored in context. */ From 51cefc9da400b953fee749c9e5d26cd4a2b5d758 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Mon, 22 Apr 2024 17:26:02 +0200 Subject: [PATCH 074/107] mlxsw: spectrum_acl_tcam: Fix memory leak when canceling rehash work [ Upstream commit fb4e2b70a7194b209fc7320bbf33b375f7114bd5 ] The rehash delayed work is rescheduled with a delay if the number of credits at end of the work is not negative as supposedly it means that the migration ended. Otherwise, it is rescheduled immediately. After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during rehash" the above is no longer accurate as a non-negative number of credits is no longer indicative of the migration being done. It can also happen if the work encountered an error in which case the migration will resume the next time the work is scheduled. The significance of the above is that it is possible for the work to be pending and associated with hints that were allocated when the migration started. This leads to the hints being leaked [1] when the work is canceled while pending as part of ACL region dismantle. Fix by freeing the hints if hints are associated with a work that was canceled while pending. Blame the original commit since the reliance on not having a pending work associated with hints is fragile. [1] unreferenced object 0xffff88810e7c3000 (size 256): comm "kworker/0:16", pid 176, jiffies 4295460353 hex dump (first 32 bytes): 00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a....... 00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@........... backtrace (crc 2544ddb9): [<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0 [<000000004d9a1ad9>] objagg_hints_get+0x42/0x390 [<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400 [<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160 [<00000000e81fd734>] process_one_work+0x59c/0xf20 [<00000000ceee9e81>] worker_thread+0x799/0x12c0 [<00000000bda6fe39>] kthread+0x246/0x300 [<0000000070056d23>] ret_from_fork+0x34/0x70 [<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30 Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work") Signed-off-by: Ido Schimmel Tested-by: Alexander Zubkov Signed-off-by: Petr Machata Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index 89ce9b1233bd..9ccbd65d5b2e 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -874,10 +874,14 @@ mlxsw_sp_acl_tcam_vregion_destroy(struct mlxsw_sp *mlxsw_sp, struct mlxsw_sp_acl_tcam *tcam = vregion->tcam; if (vgroup->vregion_rehash_enabled && ops->region_rehash_hints_get) { + struct mlxsw_sp_acl_tcam_rehash_ctx *ctx = &vregion->rehash.ctx; + mutex_lock(&tcam->lock); list_del(&vregion->tlist); mutex_unlock(&tcam->lock); - cancel_delayed_work_sync(&vregion->rehash.dw); + if (cancel_delayed_work_sync(&vregion->rehash.dw) && + ctx->hints_priv) + ops->region_rehash_hints_put(ctx->hints_priv); } mlxsw_sp_acl_tcam_vgroup_vregion_detach(mlxsw_sp, vregion); if (vregion->region2) From 546d0fe9d76e8229a67369f9cb61e961d99038bd Mon Sep 17 00:00:00 2001 From: Sindhu Devale Date: Tue, 23 Apr 2024 11:27:17 -0700 Subject: [PATCH 075/107] i40e: Do not use WQ_MEM_RECLAIM flag for workqueue [ Upstream commit 2cc7d150550cc981aceedf008f5459193282425c ] Issue reported by customer during SRIOV testing, call trace: When both i40e and the i40iw driver are loaded, a warning in check_flush_dependency is being triggered. This seems to be because of the i40e driver workqueue is allocated with the WQ_MEM_RECLAIM flag, and the i40iw one is not. Similar error was encountered on ice too and it was fixed by removing the flag. Do the same for i40e too. [Feb 9 09:08] ------------[ cut here ]------------ [ +0.000004] workqueue: WQ_MEM_RECLAIM i40e:i40e_service_task [i40e] is flushing !WQ_MEM_RECLAIM infiniband:0x0 [ +0.000060] WARNING: CPU: 0 PID: 937 at kernel/workqueue.c:2966 check_flush_dependency+0x10b/0x120 [ +0.000007] Modules linked in: snd_seq_dummy snd_hrtimer snd_seq snd_timer snd_seq_device snd soundcore nls_utf8 cifs cifs_arc4 nls_ucs2_utils rdma_cm iw_cm ib_cm cifs_md4 dns_resolver netfs qrtr rfkill sunrpc vfat fat intel_rapl_msr intel_rapl_common irdma intel_uncore_frequency intel_uncore_frequency_common ice ipmi_ssif isst_if_common skx_edac nfit libnvdimm x86_pkg_temp_thermal intel_powerclamp gnss coretemp ib_uverbs rapl intel_cstate ib_core iTCO_wdt iTCO_vendor_support acpi_ipmi mei_me ipmi_si intel_uncore ioatdma i2c_i801 joydev pcspkr mei ipmi_devintf lpc_ich intel_pch_thermal i2c_smbus ipmi_msghandler acpi_power_meter acpi_pad xfs libcrc32c ast sd_mod drm_shmem_helper t10_pi drm_kms_helper sg ixgbe drm i40e ahci crct10dif_pclmul libahci crc32_pclmul igb crc32c_intel libata ghash_clmulni_intel i2c_algo_bit mdio dca wmi dm_mirror dm_region_hash dm_log dm_mod fuse [ +0.000050] CPU: 0 PID: 937 Comm: kworker/0:3 Kdump: loaded Not tainted 6.8.0-rc2-Feb-net_dev-Qiueue-00279-gbd43c5687e05 #1 [ +0.000003] Hardware name: Intel Corporation S2600BPB/S2600BPB, BIOS SE5C620.86B.02.01.0013.121520200651 12/15/2020 [ +0.000001] Workqueue: i40e i40e_service_task [i40e] [ +0.000024] RIP: 0010:check_flush_dependency+0x10b/0x120 [ +0.000003] Code: ff 49 8b 54 24 18 48 8d 8b b0 00 00 00 49 89 e8 48 81 c6 b0 00 00 00 48 c7 c7 b0 97 fa 9f c6 05 8a cc 1f 02 01 e8 35 b3 fd ff <0f> 0b e9 10 ff ff ff 80 3d 78 cc 1f 02 00 75 94 e9 46 ff ff ff 90 [ +0.000002] RSP: 0018:ffffbd294976bcf8 EFLAGS: 00010282 [ +0.000002] RAX: 0000000000000000 RBX: ffff94d4c483c000 RCX: 0000000000000027 [ +0.000001] RDX: ffff94d47f620bc8 RSI: 0000000000000001 RDI: ffff94d47f620bc0 [ +0.000001] RBP: 0000000000000000 R08: 0000000000000000 R09: 00000000ffff7fff [ +0.000001] R10: ffffbd294976bb98 R11: ffffffffa0be65e8 R12: ffff94c5451ea180 [ +0.000001] R13: ffff94c5ab5e8000 R14: ffff94c5c20b6e05 R15: ffff94c5f1330ab0 [ +0.000001] FS: 0000000000000000(0000) GS:ffff94d47f600000(0000) knlGS:0000000000000000 [ +0.000002] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000001] CR2: 00007f9e6f1fca70 CR3: 0000000038e20004 CR4: 00000000007706f0 [ +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ +0.000001] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ +0.000001] PKRU: 55555554 [ +0.000001] Call Trace: [ +0.000001] [ +0.000002] ? __warn+0x80/0x130 [ +0.000003] ? check_flush_dependency+0x10b/0x120 [ +0.000002] ? report_bug+0x195/0x1a0 [ +0.000005] ? handle_bug+0x3c/0x70 [ +0.000003] ? exc_invalid_op+0x14/0x70 [ +0.000002] ? asm_exc_invalid_op+0x16/0x20 [ +0.000006] ? check_flush_dependency+0x10b/0x120 [ +0.000002] ? check_flush_dependency+0x10b/0x120 [ +0.000002] __flush_workqueue+0x126/0x3f0 [ +0.000015] ib_cache_cleanup_one+0x1c/0xe0 [ib_core] [ +0.000056] __ib_unregister_device+0x6a/0xb0 [ib_core] [ +0.000023] ib_unregister_device_and_put+0x34/0x50 [ib_core] [ +0.000020] i40iw_close+0x4b/0x90 [irdma] [ +0.000022] i40e_notify_client_of_netdev_close+0x54/0xc0 [i40e] [ +0.000035] i40e_service_task+0x126/0x190 [i40e] [ +0.000024] process_one_work+0x174/0x340 [ +0.000003] worker_thread+0x27e/0x390 [ +0.000001] ? __pfx_worker_thread+0x10/0x10 [ +0.000002] kthread+0xdf/0x110 [ +0.000002] ? __pfx_kthread+0x10/0x10 [ +0.000002] ret_from_fork+0x2d/0x50 [ +0.000003] ? __pfx_kthread+0x10/0x10 [ +0.000001] ret_from_fork_asm+0x1b/0x30 [ +0.000004] [ +0.000001] ---[ end trace 0000000000000000 ]--- Fixes: 4d5957cbdecd ("i40e: remove WQ_UNBOUND and the task limit of our workqueue") Signed-off-by: Sindhu Devale Reviewed-by: Arkadiusz Kubalewski Reviewed-by: Mateusz Polchlopek Signed-off-by: Aleksandr Loktionov Tested-by: Robert Ganzynkowicz Signed-off-by: Tony Nguyen Link: https://lore.kernel.org/r/20240423182723.740401-2-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/intel/i40e/i40e_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index f7d41ba110a7..dfa06737ff05 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -15971,7 +15971,7 @@ static int __init i40e_init_module(void) * since we need to be able to guarantee forward progress even under * memory pressure. */ - i40e_wq = alloc_workqueue("%s", WQ_MEM_RECLAIM, 0, i40e_driver_name); + i40e_wq = alloc_workqueue("%s", 0, 0, i40e_driver_name); if (!i40e_wq) { pr_err("%s: Failed to create workqueue\n", i40e_driver_name); return -ENOMEM; From 4077b864ffa80a171ccbe749f68fa9d9176bf962 Mon Sep 17 00:00:00 2001 From: Sudheer Mogilappagari Date: Tue, 23 Apr 2024 11:27:19 -0700 Subject: [PATCH 076/107] iavf: Fix TC config comparison with existing adapter TC config [ Upstream commit 54976cf58d6168b8d15cebb395069f23b2f34b31 ] Same number of TCs doesn't imply that underlying TC configs are same. The config could be different due to difference in number of queues in each TC. Add utility function to determine if TC configs are same. Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf") Signed-off-by: Sudheer Mogilappagari Tested-by: Mineri Bhange (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- drivers/net/ethernet/intel/iavf/iavf_main.c | 30 ++++++++++++++++++++- 1 file changed, 29 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/iavf/iavf_main.c b/drivers/net/ethernet/intel/iavf/iavf_main.c index 9cf556fedc70..8cc20db625c2 100644 --- a/drivers/net/ethernet/intel/iavf/iavf_main.c +++ b/drivers/net/ethernet/intel/iavf/iavf_main.c @@ -2647,6 +2647,34 @@ static void iavf_del_all_cloud_filters(struct iavf_adapter *adapter) spin_unlock_bh(&adapter->cloud_filter_list_lock); } +/** + * iavf_is_tc_config_same - Compare the mqprio TC config with the + * TC config already configured on this adapter. + * @adapter: board private structure + * @mqprio_qopt: TC config received from kernel. + * + * This function compares the TC config received from the kernel + * with the config already configured on the adapter. + * + * Return: True if configuration is same, false otherwise. + **/ +static bool iavf_is_tc_config_same(struct iavf_adapter *adapter, + struct tc_mqprio_qopt *mqprio_qopt) +{ + struct virtchnl_channel_info *ch = &adapter->ch_config.ch_info[0]; + int i; + + if (adapter->num_tc != mqprio_qopt->num_tc) + return false; + + for (i = 0; i < adapter->num_tc; i++) { + if (ch[i].count != mqprio_qopt->count[i] || + ch[i].offset != mqprio_qopt->offset[i]) + return false; + } + return true; +} + /** * __iavf_setup_tc - configure multiple traffic classes * @netdev: network interface device structure @@ -2703,7 +2731,7 @@ static int __iavf_setup_tc(struct net_device *netdev, void *type_data) if (ret) return ret; /* Return if same TC config is requested */ - if (adapter->num_tc == num_tc) + if (iavf_is_tc_config_same(adapter, &mqprio_qopt->qopt)) return 0; adapter->num_tc = num_tc; From eb27704f0da8c0c9d0997cf5871709d8cff1961a Mon Sep 17 00:00:00 2001 From: Kuniyuki Iwashima Date: Wed, 24 Apr 2024 10:04:43 -0700 Subject: [PATCH 077/107] af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc(). [ Upstream commit 1971d13ffa84a551d29a81fdf5b5ec5be166ac83 ] syzbot reported a lockdep splat regarding unix_gc_lock and unix_state_lock(). One is called from recvmsg() for a connected socket, and another is called from GC for TCP_LISTEN socket. So, the splat is false-positive. Let's add a dedicated lock class for the latter to suppress the splat. Note that this change is not necessary for net-next.git as the issue is only applied to the old GC impl. [0]: WARNING: possible circular locking dependency detected 6.9.0-rc5-syzkaller-00007-g4d2008430ce8 #0 Not tainted ----------------------------------------------------- kworker/u8:1/11 is trying to acquire lock: ffff88807cea4e70 (&u->lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff88807cea4e70 (&u->lock){+.+.}-{2:2}, at: __unix_gc+0x40e/0xf70 net/unix/garbage.c:302 but task is already holding lock: ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: __unix_gc+0x117/0xf70 net/unix/garbage.c:261 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (unix_gc_lock){+.+.}-{2:2}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] unix_notinflight+0x13d/0x390 net/unix/garbage.c:140 unix_detach_fds net/unix/af_unix.c:1819 [inline] unix_destruct_scm+0x221/0x350 net/unix/af_unix.c:1876 skb_release_head_state+0x100/0x250 net/core/skbuff.c:1188 skb_release_all net/core/skbuff.c:1200 [inline] __kfree_skb net/core/skbuff.c:1216 [inline] kfree_skb_reason+0x16d/0x3b0 net/core/skbuff.c:1252 kfree_skb include/linux/skbuff.h:1262 [inline] manage_oob net/unix/af_unix.c:2672 [inline] unix_stream_read_generic+0x1125/0x2700 net/unix/af_unix.c:2749 unix_stream_splice_read+0x239/0x320 net/unix/af_unix.c:2981 do_splice_read fs/splice.c:985 [inline] splice_file_to_pipe+0x299/0x500 fs/splice.c:1295 do_splice+0xf2d/0x1880 fs/splice.c:1379 __do_splice fs/splice.c:1436 [inline] __do_sys_splice fs/splice.c:1652 [inline] __se_sys_splice+0x331/0x4a0 fs/splice.c:1634 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (&u->lock){+.+.}-{2:2}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] __unix_gc+0x40e/0xf70 net/unix/garbage.c:302 process_one_work kernel/workqueue.c:3254 [inline] process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335 worker_thread+0x86d/0xd70 kernel/workqueue.c:3416 kthread+0x2f0/0x390 kernel/kthread.c:388 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(unix_gc_lock); lock(&u->lock); lock(unix_gc_lock); lock(&u->lock); *** DEADLOCK *** 3 locks held by kworker/u8:1/11: #0: ffff888015089148 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3229 [inline] #0: ffff888015089148 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_scheduled_works+0x8e0/0x17c0 kernel/workqueue.c:3335 #1: ffffc90000107d00 (unix_gc_work){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3230 [inline] #1: ffffc90000107d00 (unix_gc_work){+.+.}-{0:0}, at: process_scheduled_works+0x91b/0x17c0 kernel/workqueue.c:3335 #2: ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] #2: ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: __unix_gc+0x117/0xf70 net/unix/garbage.c:261 stack backtrace: CPU: 0 PID: 11 Comm: kworker/u8:1 Not tainted 6.9.0-rc5-syzkaller-00007-g4d2008430ce8 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Workqueue: events_unbound __unix_gc Call Trace: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2187 check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] __unix_gc+0x40e/0xf70 net/unix/garbage.c:302 process_one_work kernel/workqueue.c:3254 [inline] process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335 worker_thread+0x86d/0xd70 kernel/workqueue.c:3416 kthread+0x2f0/0x390 kernel/kthread.c:388 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Fixes: 47d8ac011fe1 ("af_unix: Fix garbage collector racing against connect()") Reported-and-tested-by: syzbot+fa379358c28cc87cc307@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=fa379358c28cc87cc307 Signed-off-by: Kuniyuki Iwashima Link: https://lore.kernel.org/r/20240424170443.9832-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin --- include/net/af_unix.h | 3 +++ net/unix/garbage.c | 2 +- 2 files changed, 4 insertions(+), 1 deletion(-) diff --git a/include/net/af_unix.h b/include/net/af_unix.h index e7612295b262..96765349d6f1 100644 --- a/include/net/af_unix.h +++ b/include/net/af_unix.h @@ -72,6 +72,9 @@ enum unix_socket_lock_class { U_LOCK_NORMAL, U_LOCK_SECOND, /* for double locking, see unix_state_double_lock(). */ U_LOCK_DIAG, /* used while dumping icons, see sk_diag_dump_icons(). */ + U_LOCK_GC_LISTENER, /* used for listening socket while determining gc + * candidates to close a small race window. + */ }; static inline void unix_state_lock_nested(struct sock *sk, diff --git a/net/unix/garbage.c b/net/unix/garbage.c index 58525311e903..133ba5be4b58 100644 --- a/net/unix/garbage.c +++ b/net/unix/garbage.c @@ -260,7 +260,7 @@ void unix_gc(void) __set_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags); if (sk->sk_state == TCP_LISTEN) { - unix_state_lock(sk); + unix_state_lock_nested(sk, U_LOCK_GC_LISTENER); unix_state_unlock(sk); } } From e8646f5d345654f905b2bf847f428363ac6aa59e Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Thu, 14 Sep 2023 20:43:18 +0206 Subject: [PATCH 078/107] serial: core: Provide port lock wrappers MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit b0af4bcb49464c221ad5f95d40f2b1b252ceedcc ] When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. Provide wrapper functions for spin_[un]lock*(port->lock) invocations so that the console mechanics can be applied later on at a single place and does not require to copy the same logic all over the drivers. Signed-off-by: Thomas Gleixner Reviewed-by: Ilpo Järvinen Signed-off-by: John Ogness Link: https://lore.kernel.org/r/20230914183831.587273-2-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman Stable-dep-of: 54c4ec5f8c47 ("serial: mxs-auart: add spinlock around changing cts state") Signed-off-by: Sasha Levin --- include/linux/serial_core.h | 79 +++++++++++++++++++++++++++++++++++++ 1 file changed, 79 insertions(+) diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 10f209d54f18..bc374d9df99f 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -255,6 +255,85 @@ struct uart_port { void *private_data; /* generic platform data pointer */ }; +/** + * uart_port_lock - Lock the UART port + * @up: Pointer to UART port structure + */ +static inline void uart_port_lock(struct uart_port *up) +{ + spin_lock(&up->lock); +} + +/** + * uart_port_lock_irq - Lock the UART port and disable interrupts + * @up: Pointer to UART port structure + */ +static inline void uart_port_lock_irq(struct uart_port *up) +{ + spin_lock_irq(&up->lock); +} + +/** + * uart_port_lock_irqsave - Lock the UART port, save and disable interrupts + * @up: Pointer to UART port structure + * @flags: Pointer to interrupt flags storage + */ +static inline void uart_port_lock_irqsave(struct uart_port *up, unsigned long *flags) +{ + spin_lock_irqsave(&up->lock, *flags); +} + +/** + * uart_port_trylock - Try to lock the UART port + * @up: Pointer to UART port structure + * + * Returns: True if lock was acquired, false otherwise + */ +static inline bool uart_port_trylock(struct uart_port *up) +{ + return spin_trylock(&up->lock); +} + +/** + * uart_port_trylock_irqsave - Try to lock the UART port, save and disable interrupts + * @up: Pointer to UART port structure + * @flags: Pointer to interrupt flags storage + * + * Returns: True if lock was acquired, false otherwise + */ +static inline bool uart_port_trylock_irqsave(struct uart_port *up, unsigned long *flags) +{ + return spin_trylock_irqsave(&up->lock, *flags); +} + +/** + * uart_port_unlock - Unlock the UART port + * @up: Pointer to UART port structure + */ +static inline void uart_port_unlock(struct uart_port *up) +{ + spin_unlock(&up->lock); +} + +/** + * uart_port_unlock_irq - Unlock the UART port and re-enable interrupts + * @up: Pointer to UART port structure + */ +static inline void uart_port_unlock_irq(struct uart_port *up) +{ + spin_unlock_irq(&up->lock); +} + +/** + * uart_port_lock_irqrestore - Unlock the UART port, restore interrupts + * @up: Pointer to UART port structure + * @flags: The saved interrupt flags for restore + */ +static inline void uart_port_unlock_irqrestore(struct uart_port *up, unsigned long flags) +{ + spin_unlock_irqrestore(&up->lock, flags); +} + static inline int serial_port_in(struct uart_port *up, int offset) { return up->serial_in(up, offset); From 21535ef0ac1945080198fe3e4347ea498205c99a Mon Sep 17 00:00:00 2001 From: Emil Kronborg Date: Wed, 20 Mar 2024 12:15:36 +0000 Subject: [PATCH 079/107] serial: mxs-auart: add spinlock around changing cts state [ Upstream commit 54c4ec5f8c471b7c1137a1f769648549c423c026 ] The uart_handle_cts_change() function in serial_core expects the caller to hold uport->lock. For example, I have seen the below kernel splat, when the Bluetooth driver is loaded on an i.MX28 board. [ 85.119255] ------------[ cut here ]------------ [ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec [ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs [ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1 [ 85.151396] Hardware name: Freescale MXS (Device Tree) [ 85.156679] Workqueue: hci0 hci_power_on [bluetooth] (...) [ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4 [ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210 (...) Cc: stable@vger.kernel.org Fixes: 4d90bb147ef6 ("serial: core: Document and assert lock requirements for irq helpers") Reviewed-by: Frank Li Signed-off-by: Emil Kronborg Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin --- drivers/tty/serial/mxs-auart.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c index 5d483e996514..a8eb98e37af4 100644 --- a/drivers/tty/serial/mxs-auart.c +++ b/drivers/tty/serial/mxs-auart.c @@ -1126,11 +1126,13 @@ static void mxs_auart_set_ldisc(struct uart_port *port, static irqreturn_t mxs_auart_irq_handle(int irq, void *context) { - u32 istat; + u32 istat, stat; struct mxs_auart_port *s = context; u32 mctrl_temp = s->mctrl_prev; - u32 stat = mxs_read(s, REG_STAT); + uart_port_lock(&s->port); + + stat = mxs_read(s, REG_STAT); istat = mxs_read(s, REG_INTR); /* ack irq */ @@ -1166,6 +1168,8 @@ static irqreturn_t mxs_auart_irq_handle(int irq, void *context) istat &= ~AUART_INTR_TXIS; } + uart_port_unlock(&s->port); + return IRQ_HANDLED; } From 3b418dca9a7c0c3c7dd169eb87bd6b65352c827c Mon Sep 17 00:00:00 2001 From: Rajneesh Bhardwaj Date: Sat, 25 Apr 2020 01:01:12 -0400 Subject: [PATCH 080/107] drm/amdgpu: restrict bo mapping within gpu address limits MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 8b80d74bdb2285d3022b349c8451eb16535f7906 ] Have strict check on bo mapping since on some systems, such as A+A or hybrid, the cpu might support 5 level paging or can address memory above 48 bits but gpu might be limited by hardware to just use 48 bits. In general, this applies to all asics where this limitation can be checked against their max_pfn range. This restricts the range to map bo within pratical limits of cpu and gpu for shared virtual memory access. Reviewed-by: Oak Zeng Reviewed-by: Christian König Reviewed-by: Hawking Zhang Acked-by: Alex Deucher Signed-off-by: Rajneesh Bhardwaj Signed-off-by: Alex Deucher Stable-dep-of: 6fef2d4c00b5 ("drm/amdgpu: validate the parameters of bo mapping operations more clearly") Signed-off-by: Sasha Levin --- drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c index dcf23b43f323..88f2707c69ce 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c @@ -2130,7 +2130,8 @@ int amdgpu_vm_bo_map(struct amdgpu_device *adev, /* make sure object fit at this offset */ eaddr = saddr + size - 1; if (saddr >= eaddr || - (bo && offset + size > amdgpu_bo_size(bo))) + (bo && offset + size > amdgpu_bo_size(bo)) || + (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) return -EINVAL; saddr /= AMDGPU_GPU_PAGE_SIZE; @@ -2195,7 +2196,8 @@ int amdgpu_vm_bo_replace_map(struct amdgpu_device *adev, /* make sure object fit at this offset */ eaddr = saddr + size - 1; if (saddr >= eaddr || - (bo && offset + size > amdgpu_bo_size(bo))) + (bo && offset + size > amdgpu_bo_size(bo)) || + (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) return -EINVAL; /* Allocate all the needed memory */ From d83c337e654d58d3edd15a2ae76e87dc601c07d9 Mon Sep 17 00:00:00 2001 From: Chia-I Wu Date: Thu, 1 Jun 2023 15:44:12 -0700 Subject: [PATCH 081/107] amdgpu: validate offset_in_bo of drm_amdgpu_gem_va MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 9f0bcf49e9895cb005d78b33a5eebfa11711b425 ] This is motivated by OOB access in amdgpu_vm_update_range when offset_in_bo+map_size overflows. v2: keep the validations in amdgpu_vm_bo_map v3: add the validations to amdgpu_vm_bo_map/amdgpu_vm_bo_replace_map rather than to amdgpu_gem_va_ioctl Fixes: 9f7eb5367d00 ("drm/amdgpu: actually use the VM map parameters") Reviewed-by: Christian König Signed-off-by: Chia-I Wu Signed-off-by: Alex Deucher Stable-dep-of: 6fef2d4c00b5 ("drm/amdgpu: validate the parameters of bo mapping operations more clearly") Signed-off-by: Sasha Levin --- drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c index 88f2707c69ce..dfec651ec0b4 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c @@ -2123,14 +2123,14 @@ int amdgpu_vm_bo_map(struct amdgpu_device *adev, uint64_t eaddr; /* validate the parameters */ - if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || - size == 0 || size & ~PAGE_MASK) + if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK) + return -EINVAL; + if (saddr + size <= saddr || offset + size <= offset) return -EINVAL; /* make sure object fit at this offset */ eaddr = saddr + size - 1; - if (saddr >= eaddr || - (bo && offset + size > amdgpu_bo_size(bo)) || + if ((bo && offset + size > amdgpu_bo_size(bo)) || (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) return -EINVAL; @@ -2189,14 +2189,14 @@ int amdgpu_vm_bo_replace_map(struct amdgpu_device *adev, int r; /* validate the parameters */ - if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || - size == 0 || size & ~PAGE_MASK) + if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK) + return -EINVAL; + if (saddr + size <= saddr || offset + size <= offset) return -EINVAL; /* make sure object fit at this offset */ eaddr = saddr + size - 1; - if (saddr >= eaddr || - (bo && offset + size > amdgpu_bo_size(bo)) || + if ((bo && offset + size > amdgpu_bo_size(bo)) || (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) return -EINVAL; From f68039375d4d6d67303674c0ab2d06b7295c0ec9 Mon Sep 17 00:00:00 2001 From: xinhui pan Date: Thu, 11 Apr 2024 11:11:38 +0800 Subject: [PATCH 082/107] drm/amdgpu: validate the parameters of bo mapping operations more clearly MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [ Upstream commit 6fef2d4c00b5b8561ad68dd2b68173f5c6af1e75 ] Verify the parameters of amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place. Fixes: dc54d3d1744d ("drm/amdgpu: implement AMDGPU_VA_OP_CLEAR v2") Cc: stable@vger.kernel.org Reported-by: Vlad Stolyarov Suggested-by: Christian König Signed-off-by: xinhui pan Reviewed-by: Christian König Signed-off-by: Alex Deucher Signed-off-by: Sasha Levin --- drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c | 72 ++++++++++++++++---------- 1 file changed, 46 insertions(+), 26 deletions(-) diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c index dfec651ec0b4..1da72ecf0fac 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c @@ -2095,6 +2095,37 @@ static void amdgpu_vm_bo_insert_map(struct amdgpu_device *adev, trace_amdgpu_vm_bo_map(bo_va, mapping); } +/* Validate operation parameters to prevent potential abuse */ +static int amdgpu_vm_verify_parameters(struct amdgpu_device *adev, + struct amdgpu_bo *bo, + uint64_t saddr, + uint64_t offset, + uint64_t size) +{ + uint64_t tmp, lpfn; + + if (saddr & AMDGPU_GPU_PAGE_MASK + || offset & AMDGPU_GPU_PAGE_MASK + || size & AMDGPU_GPU_PAGE_MASK) + return -EINVAL; + + if (check_add_overflow(saddr, size, &tmp) + || check_add_overflow(offset, size, &tmp) + || size == 0 /* which also leads to end < begin */) + return -EINVAL; + + /* make sure object fit at this offset */ + if (bo && offset + size > amdgpu_bo_size(bo)) + return -EINVAL; + + /* Ensure last pfn not exceed max_pfn */ + lpfn = (saddr + size - 1) >> AMDGPU_GPU_PAGE_SHIFT; + if (lpfn >= adev->vm_manager.max_pfn) + return -EINVAL; + + return 0; +} + /** * amdgpu_vm_bo_map - map bo inside a vm * @@ -2121,21 +2152,14 @@ int amdgpu_vm_bo_map(struct amdgpu_device *adev, struct amdgpu_bo *bo = bo_va->base.bo; struct amdgpu_vm *vm = bo_va->base.vm; uint64_t eaddr; + int r; - /* validate the parameters */ - if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK) - return -EINVAL; - if (saddr + size <= saddr || offset + size <= offset) - return -EINVAL; - - /* make sure object fit at this offset */ - eaddr = saddr + size - 1; - if ((bo && offset + size > amdgpu_bo_size(bo)) || - (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) - return -EINVAL; + r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size); + if (r) + return r; saddr /= AMDGPU_GPU_PAGE_SIZE; - eaddr /= AMDGPU_GPU_PAGE_SIZE; + eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE; tmp = amdgpu_vm_it_iter_first(&vm->va, saddr, eaddr); if (tmp) { @@ -2188,17 +2212,9 @@ int amdgpu_vm_bo_replace_map(struct amdgpu_device *adev, uint64_t eaddr; int r; - /* validate the parameters */ - if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK) - return -EINVAL; - if (saddr + size <= saddr || offset + size <= offset) - return -EINVAL; - - /* make sure object fit at this offset */ - eaddr = saddr + size - 1; - if ((bo && offset + size > amdgpu_bo_size(bo)) || - (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT)) - return -EINVAL; + r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size); + if (r) + return r; /* Allocate all the needed memory */ mapping = kmalloc(sizeof(*mapping), GFP_KERNEL); @@ -2212,7 +2228,7 @@ int amdgpu_vm_bo_replace_map(struct amdgpu_device *adev, } saddr /= AMDGPU_GPU_PAGE_SIZE; - eaddr /= AMDGPU_GPU_PAGE_SIZE; + eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE; mapping->start = saddr; mapping->last = eaddr; @@ -2299,10 +2315,14 @@ int amdgpu_vm_bo_clear_mappings(struct amdgpu_device *adev, struct amdgpu_bo_va_mapping *before, *after, *tmp, *next; LIST_HEAD(removed); uint64_t eaddr; + int r; + + r = amdgpu_vm_verify_parameters(adev, NULL, saddr, 0, size); + if (r) + return r; - eaddr = saddr + size - 1; saddr /= AMDGPU_GPU_PAGE_SIZE; - eaddr /= AMDGPU_GPU_PAGE_SIZE; + eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE; /* Allocate all the needed memory */ before = kzalloc(sizeof(*before), GFP_KERNEL); From 62c724e5ec00e8ba27252915c2679bd4d4ebc204 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 29 Apr 2024 12:53:46 +0200 Subject: [PATCH 083/107] Revert "crypto: api - Disallow identical driver names" This reverts commit cf6889bb8b56d15f15d9b8e47ccab7b3b4c74bd6 which is commit 27016f75f5ed47e2d8e0ca75a8ff1f40bc1a5e27 upstream. It is reported to cause problems in older kernels due to some crypto drivers having the same name, so revert it here to fix the problems. Link: https://lore.kernel.org/r/aceda6e2-cefb-4146-aef8-ff4bafa56e56@roeck-us.net Reported-by: Guenter Roeck Cc: Ovidiu Panait Cc: Herbert Xu Signed-off-by: Greg Kroah-Hartman --- crypto/algapi.c | 1 - 1 file changed, 1 deletion(-) diff --git a/crypto/algapi.c b/crypto/algapi.c index afe148d0f72d..fff52bc9d97d 100644 --- a/crypto/algapi.c +++ b/crypto/algapi.c @@ -217,7 +217,6 @@ static struct crypto_larval *__crypto_register_alg(struct crypto_alg *alg) } if (!strcmp(q->cra_driver_name, alg->cra_name) || - !strcmp(q->cra_driver_name, alg->cra_driver_name) || !strcmp(q->cra_name, alg->cra_driver_name)) goto err; } From c9e38f7ad6352797a45df0e88f33c5fadb5e90b8 Mon Sep 17 00:00:00 2001 From: Shifeng Li Date: Sat, 2 Dec 2023 00:01:26 -0800 Subject: [PATCH 084/107] net/mlx5e: Fix a race in command alloc flow commit 8f5100da56b3980276234e812ce98d8f075194cd upstream. Fix a cmd->ent use after free due to a race on command entry. Such race occurs when one of the commands releases its last refcount and frees its index and entry while another process running command flush flow takes refcount to this command entry. The process which handles commands flush may see this command as needed to be flushed if the other process allocated a ent->idx but didn't set ent to cmd->ent_arr in cmd_work_handler(). Fix it by moving the assignment of cmd->ent_arr into the spin lock. [70013.081955] BUG: KASAN: use-after-free in mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core] [70013.081967] Write of size 4 at addr ffff88880b1510b4 by task kworker/26:1/1433361 [70013.081968] [70013.082028] Workqueue: events aer_isr [70013.082053] Call Trace: [70013.082067] dump_stack+0x8b/0xbb [70013.082086] print_address_description+0x6a/0x270 [70013.082102] kasan_report+0x179/0x2c0 [70013.082173] mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core] [70013.082267] mlx5_cmd_flush+0x80/0x180 [mlx5_core] [70013.082304] mlx5_enter_error_state+0x106/0x1d0 [mlx5_core] [70013.082338] mlx5_try_fast_unload+0x2ea/0x4d0 [mlx5_core] [70013.082377] remove_one+0x200/0x2b0 [mlx5_core] [70013.082409] pci_device_remove+0xf3/0x280 [70013.082439] device_release_driver_internal+0x1c3/0x470 [70013.082453] pci_stop_bus_device+0x109/0x160 [70013.082468] pci_stop_and_remove_bus_device+0xe/0x20 [70013.082485] pcie_do_fatal_recovery+0x167/0x550 [70013.082493] aer_isr+0x7d2/0x960 [70013.082543] process_one_work+0x65f/0x12d0 [70013.082556] worker_thread+0x87/0xb50 [70013.082571] kthread+0x2e9/0x3a0 [70013.082592] ret_from_fork+0x1f/0x40 The logical relationship of this error is as follows: aer_recover_work | ent->work -------------------------------------------+------------------------------ aer_recover_work_func | |- pcie_do_recovery | |- report_error_detected | |- mlx5_pci_err_detected |cmd_work_handler |- mlx5_enter_error_state | |- cmd_alloc_index |- enter_error_state | |- lock cmd->alloc_lock |- mlx5_cmd_flush | |- clear_bit |- mlx5_cmd_trigger_completions| |- unlock cmd->alloc_lock |- lock cmd->alloc_lock | |- vector = ~dev->cmd.vars.bitmask |- for_each_set_bit | |- cmd_ent_get(cmd->ent_arr[i]) (UAF) |- unlock cmd->alloc_lock | |- cmd->ent_arr[ent->idx]=ent The cmd->ent_arr[ent->idx] assignment and the bit clearing are not protected by the cmd->alloc_lock in cmd_work_handler(). Fixes: 50b2412b7e78 ("net/mlx5: Avoid possible free of command entry while timeout comp handler") Reviewed-by: Moshe Shemesh Signed-off-by: Shifeng Li Signed-off-by: Saeed Mahameed Signed-off-by: Samasth Norway Ananda Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/mellanox/mlx5/core/cmd.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/mellanox/mlx5/core/cmd.c b/drivers/net/ethernet/mellanox/mlx5/core/cmd.c index 93a6597366f5..ebf5b30b2100 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/cmd.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/cmd.c @@ -114,15 +114,18 @@ static u8 alloc_token(struct mlx5_cmd *cmd) return token; } -static int cmd_alloc_index(struct mlx5_cmd *cmd) +static int cmd_alloc_index(struct mlx5_cmd *cmd, struct mlx5_cmd_work_ent *ent) { unsigned long flags; int ret; spin_lock_irqsave(&cmd->alloc_lock, flags); ret = find_first_bit(&cmd->bitmask, cmd->max_reg_cmds); - if (ret < cmd->max_reg_cmds) + if (ret < cmd->max_reg_cmds) { clear_bit(ret, &cmd->bitmask); + ent->idx = ret; + cmd->ent_arr[ent->idx] = ent; + } spin_unlock_irqrestore(&cmd->alloc_lock, flags); return ret < cmd->max_reg_cmds ? ret : -ENOMEM; @@ -905,7 +908,7 @@ static void cmd_work_handler(struct work_struct *work) sem = ent->page_queue ? &cmd->pages_sem : &cmd->sem; down(sem); if (!ent->page_queue) { - alloc_ret = cmd_alloc_index(cmd); + alloc_ret = cmd_alloc_index(cmd, ent); if (alloc_ret < 0) { mlx5_core_err(dev, "failed to allocate command entry\n"); if (ent->callback) { @@ -920,15 +923,14 @@ static void cmd_work_handler(struct work_struct *work) up(sem); return; } - ent->idx = alloc_ret; } else { ent->idx = cmd->max_reg_cmds; spin_lock_irqsave(&cmd->alloc_lock, flags); clear_bit(ent->idx, &cmd->bitmask); + cmd->ent_arr[ent->idx] = ent; spin_unlock_irqrestore(&cmd->alloc_lock, flags); } - cmd->ent_arr[ent->idx] = ent; lay = get_inst(cmd, ent->idx); ent->lay = lay; memset(lay, 0, sizeof(*lay)); From 92e64e2675dd99b9d0342e51973a5a3efd593f69 Mon Sep 17 00:00:00 2001 From: "Robin H. Johnson" Date: Mon, 30 Aug 2021 21:37:22 -0700 Subject: [PATCH 085/107] tracing: Show size of requested perf buffer commit a90afe8d020da9298c98fddb19b7a6372e2feb45 upstream. If the perf buffer isn't large enough, provide a hint about how large it needs to be for whatever is running. Link: https://lkml.kernel.org/r/20210831043723.13481-1-robbat2@gentoo.org Signed-off-by: Robin H. Johnson Signed-off-by: Steven Rostedt (VMware) Signed-off-by: Greg Kroah-Hartman Signed-off-by: Thadeu Lima de Souza Cascardo --- kernel/trace/trace_event_perf.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/trace/trace_event_perf.c b/kernel/trace/trace_event_perf.c index a9dfa04ffa44..563c0e659a40 100644 --- a/kernel/trace/trace_event_perf.c +++ b/kernel/trace/trace_event_perf.c @@ -395,7 +395,8 @@ void *perf_trace_buf_alloc(int size, struct pt_regs **regs, int *rctxp) BUILD_BUG_ON(PERF_MAX_TRACE_SIZE % sizeof(unsigned long)); if (WARN_ONCE(size > PERF_MAX_TRACE_SIZE, - "perf buffer not large enough")) + "perf buffer not large enough, wanted %d, have %d", + size, PERF_MAX_TRACE_SIZE)) return NULL; *rctxp = rctx = perf_swevent_get_recursion_context(); From 049f36ee98b94a3b2c7e8a30b006402c08b31af0 Mon Sep 17 00:00:00 2001 From: "Robin H. Johnson" Date: Mon, 30 Aug 2021 21:37:23 -0700 Subject: [PATCH 086/107] tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker together commit e531e90b5ab0f7ce5ff298e165214c1aec6ed187 upstream. Running endpoint security solutions like Sentinel1 that use perf-based tracing heavily lead to this repeated dump complaining about dockerd. The default value of 2048 is nowhere near not large enough. Using the prior patch "tracing: show size of requested buffer", we get "perf buffer not large enough, wanted 6644, have 6144", after repeated up-sizing (I did 2/4/6/8K). With 8K, the problem doesn't occur at all, so below is the trace for 6K. I'm wondering if this value should be selectable at boot time, but this is a good starting point. ``` ------------[ cut here ]------------ perf buffer not large enough, wanted 6644, have 6144 WARNING: CPU: 1 PID: 4997 at kernel/trace/trace_event_perf.c:402 perf_trace_buf_alloc+0x8c/0xa0 Modules linked in: [..] CPU: 1 PID: 4997 Comm: sh Tainted: G T 5.13.13-x86_64-00039-gb3959163488e #63 Hardware name: LENOVO 20KH002JUS/20KH002JUS, BIOS N23ET66W (1.41 ) 09/02/2019 RIP: 0010:perf_trace_buf_alloc+0x8c/0xa0 Code: 80 3d 43 97 d0 01 00 74 07 31 c0 5b 5d 41 5c c3 ba 00 18 00 00 89 ee 48 c7 c7 00 82 7d 91 c6 05 25 97 d0 01 01 e8 22 ee bc 00 <0f> 0b 31 c0 eb db 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 55 89 RSP: 0018:ffffb922026b7d58 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff9da5ee012000 RCX: 0000000000000027 RDX: ffff9da881657828 RSI: 0000000000000001 RDI: ffff9da881657820 RBP: 00000000000019f4 R08: 0000000000000000 R09: ffffb922026b7b80 R10: ffffb922026b7b78 R11: ffffffff91dda688 R12: 000000000000000f R13: ffff9da5ee012108 R14: ffff9da8816570a0 R15: ffffb922026b7e30 FS: 00007f420db1a080(0000) GS:ffff9da881640000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000060 CR3: 00000002504a8006 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: kprobe_perf_func+0x11e/0x270 ? do_execveat_common.isra.0+0x1/0x1c0 ? do_execveat_common.isra.0+0x5/0x1c0 kprobe_ftrace_handler+0x10e/0x1d0 0xffffffffc03aa0c8 ? do_execveat_common.isra.0+0x1/0x1c0 do_execveat_common.isra.0+0x5/0x1c0 __x64_sys_execve+0x33/0x40 do_syscall_64+0x6b/0xc0 ? do_syscall_64+0x11/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f420dc1db37 Code: ff ff 76 e7 f7 d8 64 41 89 00 eb df 0f 1f 80 00 00 00 00 f7 d8 64 41 89 00 eb dc 0f 1f 84 00 00 00 00 00 b8 3b 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 01 43 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffd4e8b4e38 EFLAGS: 00000246 ORIG_RAX: 000000000000003b RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f420dc1db37 RDX: 0000564338d1e740 RSI: 0000564338d32d50 RDI: 0000564338d28f00 RBP: 0000564338d28f00 R08: 0000564338d32d50 R09: 0000000000000020 R10: 00000000000001b6 R11: 0000000000000246 R12: 0000564338d28f00 R13: 0000564338d32d50 R14: 0000564338d1e740 R15: 0000564338d28c60 ---[ end trace 83ab3e8e16275e49 ]--- ``` Link: https://lkml.kernel.org/r/20210831043723.13481-2-robbat2@gentoo.org Signed-off-by: Robin H. Johnson Signed-off-by: Steven Rostedt (VMware) Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: Greg Kroah-Hartman --- include/linux/trace_events.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/trace_events.h b/include/linux/trace_events.h index b8b87e7ba93f..12ee8973ea6f 100644 --- a/include/linux/trace_events.h +++ b/include/linux/trace_events.h @@ -427,7 +427,7 @@ struct trace_event_file { } \ early_initcall(trace_init_perf_perm_##name); -#define PERF_MAX_TRACE_SIZE 2048 +#define PERF_MAX_TRACE_SIZE 8192 #define MAX_FILTER_STR_VAL 256 /* Should handle KSYM_SYMBOL_LEN */ From 9c25b429056ce35861e22489ce08fe9396651b70 Mon Sep 17 00:00:00 2001 From: Nathan Chancellor Date: Mon, 1 Apr 2024 11:24:17 -0700 Subject: [PATCH 087/107] Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old() commit 9bf4e919ccad613b3596eebf1ff37b05b6405307 upstream. After an innocuous optimization change in LLVM main (19.0.0), x86_64 allmodconfig (which enables CONFIG_KCSAN / -fsanitize=thread) fails to build due to the checks in check_copy_size(): In file included from net/bluetooth/sco.c:27: In file included from include/linux/module.h:13: In file included from include/linux/stat.h:19: In file included from include/linux/time.h:60: In file included from include/linux/time32.h:13: In file included from include/linux/timex.h:67: In file included from arch/x86/include/asm/timex.h:6: In file included from arch/x86/include/asm/tsc.h:10: In file included from arch/x86/include/asm/msr.h:15: In file included from include/linux/percpu.h:7: In file included from include/linux/smp.h:118: include/linux/thread_info.h:244:4: error: call to '__bad_copy_from' declared with 'error' attribute: copy source size is too small 244 | __bad_copy_from(); | ^ The same exact error occurs in l2cap_sock.c. The copy_to_user() statements that are failing come from l2cap_sock_getsockopt_old() and sco_sock_getsockopt_old(). This does not occur with GCC with or without KCSAN or Clang without KCSAN enabled. len is defined as an 'int' because it is assigned from '__user int *optlen'. However, it is clamped against the result of sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit platforms). This is done with min_t() because min() requires compatible types, which results in both len and the result of sizeof() being casted to 'unsigned int', meaning len changes signs and the result of sizeof() is truncated. From there, len is passed to copy_to_user(), which has a third parameter type of 'unsigned long', so it is widened and changes signs again. This excessive casting in combination with the KCSAN instrumentation causes LLVM to fail to eliminate the __bad_copy_from() call, failing the build. The official recommendation from LLVM developers is to consistently use long types for all size variables to avoid the unnecessary casting in the first place. Change the type of len to size_t in both l2cap_sock_getsockopt_old() and sco_sock_getsockopt_old(). This clears up the error while allowing min_t() to be replaced with min(), resulting in simpler code with no casts and fewer implicit conversions. While len is a different type than optlen now, it should result in no functional change because the result of sizeof() will clamp all values of optlen in the same manner as before. Cc: stable@vger.kernel.org Closes: https://github.com/ClangBuiltLinux/linux/issues/2007 Link: https://github.com/llvm/llvm-project/issues/85647 Signed-off-by: Nathan Chancellor Reviewed-by: Justin Stitt Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman --- net/bluetooth/l2cap_sock.c | 7 ++++--- net/bluetooth/sco.c | 7 ++++--- 2 files changed, 8 insertions(+), 6 deletions(-) diff --git a/net/bluetooth/l2cap_sock.c b/net/bluetooth/l2cap_sock.c index 712bffa4e8b4..9eea2af9a8e1 100644 --- a/net/bluetooth/l2cap_sock.c +++ b/net/bluetooth/l2cap_sock.c @@ -405,7 +405,8 @@ static int l2cap_sock_getsockopt_old(struct socket *sock, int optname, struct l2cap_chan *chan = l2cap_pi(sk)->chan; struct l2cap_options opts; struct l2cap_conninfo cinfo; - int len, err = 0; + int err = 0; + size_t len; u32 opt; BT_DBG("sk %p", sk); @@ -450,7 +451,7 @@ static int l2cap_sock_getsockopt_old(struct socket *sock, int optname, opts.max_tx = chan->max_tx; opts.txwin_size = chan->tx_win; - len = min_t(unsigned int, len, sizeof(opts)); + len = min(len, sizeof(opts)); if (copy_to_user(optval, (char *) &opts, len)) err = -EFAULT; @@ -500,7 +501,7 @@ static int l2cap_sock_getsockopt_old(struct socket *sock, int optname, cinfo.hci_handle = chan->conn->hcon->handle; memcpy(cinfo.dev_class, chan->conn->hcon->dev_class, 3); - len = min_t(unsigned int, len, sizeof(cinfo)); + len = min(len, sizeof(cinfo)); if (copy_to_user(optval, (char *) &cinfo, len)) err = -EFAULT; diff --git a/net/bluetooth/sco.c b/net/bluetooth/sco.c index 78a549e506b1..a3b15b4e176e 100644 --- a/net/bluetooth/sco.c +++ b/net/bluetooth/sco.c @@ -880,7 +880,8 @@ static int sco_sock_getsockopt_old(struct socket *sock, int optname, struct sock *sk = sock->sk; struct sco_options opts; struct sco_conninfo cinfo; - int len, err = 0; + int err = 0; + size_t len; BT_DBG("sk %p", sk); @@ -902,7 +903,7 @@ static int sco_sock_getsockopt_old(struct socket *sock, int optname, BT_DBG("mtu %d", opts.mtu); - len = min_t(unsigned int, len, sizeof(opts)); + len = min(len, sizeof(opts)); if (copy_to_user(optval, (char *)&opts, len)) err = -EFAULT; @@ -920,7 +921,7 @@ static int sco_sock_getsockopt_old(struct socket *sock, int optname, cinfo.hci_handle = sco_pi(sk)->conn->hcon->handle; memcpy(cinfo.dev_class, sco_pi(sk)->conn->hcon->dev_class, 3); - len = min_t(unsigned int, len, sizeof(cinfo)); + len = min(len, sizeof(cinfo)); if (copy_to_user(optval, (char *)&cinfo, len)) err = -EFAULT; From 344972770c285d0a19b2c0a7f3077b45956a1e94 Mon Sep 17 00:00:00 2001 From: WangYuli Date: Fri, 29 Mar 2024 10:34:39 +0800 Subject: [PATCH 088/107] Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853 commit d1a5a7eede2977da3d2002d5ea3b519019cc1a98 upstream. Add the support ID(0x0bda, 0x4853) to usb_device_id table for Realtek RTL8852BE. Without this change the device utilizes an obsolete version of the firmware that is encoded in it rather than the updated Realtek firmware and config files from the firmware directory. The latter files implement many new features. The device table is as follows: T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=4853 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Cc: stable@vger.kernel.org Signed-off-by: Larry Finger Signed-off-by: WangYuli Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman --- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index dbba6a09e51e..10408df38c52 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -360,6 +360,8 @@ static const struct usb_device_id blacklist_table[] = { /* Realtek 8852BE Bluetooth devices */ { USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0bda, 0x4853), .driver_info = BTUSB_REALTEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0bda, 0x887b), .driver_info = BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0bda, 0xb85b), .driver_info = BTUSB_REALTEK | From 73db209dcd4ae026021234d40cfcb2fb5b564b86 Mon Sep 17 00:00:00 2001 From: Johannes Thumshirn Date: Wed, 17 Apr 2024 10:45:47 +0200 Subject: [PATCH 089/107] btrfs: fix information leak in btrfs_ioctl_logical_to_ino() commit 2f7ef5bb4a2f3e481ef05fab946edb97c84f67cf upstream. Syzbot reported the following information leak for in btrfs_ioctl_logical_to_ino(): BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:114 [inline] BUG: KMSAN: kernel-infoleak in _copy_to_user+0xbc/0x110 lib/usercopy.c:40 instrument_copy_to_user include/linux/instrumented.h:114 [inline] _copy_to_user+0xbc/0x110 lib/usercopy.c:40 copy_to_user include/linux/uaccess.h:191 [inline] btrfs_ioctl_logical_to_ino+0x440/0x750 fs/btrfs/ioctl.c:3499 btrfs_ioctl+0x714/0x1260 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0x261/0x450 fs/ioctl.c:890 __x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:890 x64_sys_call+0x1883/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:17 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: __kmalloc_large_node+0x231/0x370 mm/slub.c:3921 __do_kmalloc_node mm/slub.c:3954 [inline] __kmalloc_node+0xb07/0x1060 mm/slub.c:3973 kmalloc_node include/linux/slab.h:648 [inline] kvmalloc_node+0xc0/0x2d0 mm/util.c:634 kvmalloc include/linux/slab.h:766 [inline] init_data_container+0x49/0x1e0 fs/btrfs/backref.c:2779 btrfs_ioctl_logical_to_ino+0x17c/0x750 fs/btrfs/ioctl.c:3480 btrfs_ioctl+0x714/0x1260 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0x261/0x450 fs/ioctl.c:890 __x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:890 x64_sys_call+0x1883/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:17 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Bytes 40-65535 of 65536 are uninitialized Memory access of size 65536 starts at ffff888045a40000 This happens, because we're copying a 'struct btrfs_data_container' back to user-space. This btrfs_data_container is allocated in 'init_data_container()' via kvmalloc(), which does not zero-fill the memory. Fix this by using kvzalloc() which zeroes out the memory on allocation. CC: stable@vger.kernel.org # 4.14+ Reported-by: Reviewed-by: Qu Wenruo Reviewed-by: Filipe Manana Signed-off-by: Johannes Thumshirn Reviewed-by: David Sterba Signed-off-by: David Sterba Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/backref.c | 12 +++--------- 1 file changed, 3 insertions(+), 9 deletions(-) diff --git a/fs/btrfs/backref.c b/fs/btrfs/backref.c index 89411e96dcc0..16e5e07cb5d1 100644 --- a/fs/btrfs/backref.c +++ b/fs/btrfs/backref.c @@ -2291,20 +2291,14 @@ struct btrfs_data_container *init_data_container(u32 total_bytes) size_t alloc_bytes; alloc_bytes = max_t(size_t, total_bytes, sizeof(*data)); - data = kvmalloc(alloc_bytes, GFP_KERNEL); + data = kvzalloc(alloc_bytes, GFP_KERNEL); if (!data) return ERR_PTR(-ENOMEM); - if (total_bytes >= sizeof(*data)) { + if (total_bytes >= sizeof(*data)) data->bytes_left = total_bytes - sizeof(*data); - data->bytes_missing = 0; - } else { + else data->bytes_missing = sizeof(*data) - total_bytes; - data->bytes_left = 0; - } - - data->elem_cnt = 0; - data->elem_missed = 0; return data; } From 21722c0b07daefcd834895b2f7010703ffde88f5 Mon Sep 17 00:00:00 2001 From: Iskander Amara Date: Fri, 8 Mar 2024 09:52:42 +0100 Subject: [PATCH 090/107] arm64: dts: rockchip: enable internal pull-up for Q7_THRM# on RK3399 Puma commit 0ac417b8f124427c90ec8c2ef4f632b821d924cc upstream. Q7_THRM# pin is connected to a diode on the module which is used as a level shifter, and the pin have a pull-down enabled by default. We need to configure it to internal pull-up, other- wise whenever the pin is configured as INPUT and we try to control it externally the value will always remain zero. Signed-off-by: Iskander Amara Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM") Reviewed-by: Quentin Schulz Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240308085243.69903-1-iskander.amara@theobroma-systems.com Signed-off-by: Heiko Stuebner Signed-off-by: Greg Kroah-Hartman --- arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi index 5382c2f0b642..7fea9d6fbdcf 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi @@ -431,6 +431,16 @@ }; &pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&q7_thermal_pin>; + + gpios { + q7_thermal_pin: q7-thermal-pin { + rockchip,pins = + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + i2c8 { i2c8_xfer_a: i2c8-xfer { rockchip,pins = From 851a52eb9bdf8835daa5f080caa9bfa5a16c91ba Mon Sep 17 00:00:00 2001 From: Mukul Joshi Date: Thu, 18 Apr 2024 11:32:34 -0400 Subject: [PATCH 091/107] drm/amdgpu: Fix leak when GPU memory allocation fails commit 25e9227c6afd200bed6774c866980b8e36d033af upstream. Free the sync object if the memory allocation fails for any reason. Signed-off-by: Mukul Joshi Reviewed-by: Alex Deucher Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c index 49b52ac3e473..06c88dbc5a4a 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c @@ -1204,6 +1204,7 @@ allocate_init_user_pages_failed: err_bo_create: unreserve_mem_limit(adev, size, alloc_domain, !!sg); err_reserve_limit: + amdgpu_sync_free(&(*mem)->sync); mutex_destroy(&(*mem)->lock); kfree(*mem); err: From b72d2b1448b682844f995e660b77f2a1fabc1662 Mon Sep 17 00:00:00 2001 From: Guanrui Huang Date: Thu, 18 Apr 2024 14:10:52 +0800 Subject: [PATCH 092/107] irqchip/gic-v3-its: Prevent double free on error commit c26591afd33adce296c022e3480dea4282b7ef91 upstream. The error handling path in its_vpe_irq_domain_alloc() causes a double free when its_vpe_init() fails after successfully allocating at least one interrupt. This happens because its_vpe_irq_domain_free() frees the interrupts along with the area bitmap and the vprop_page and its_vpe_irq_domain_alloc() subsequently frees the area bitmap and the vprop_page again. Fix this by unconditionally invoking its_vpe_irq_domain_free() which handles all cases correctly and by removing the bitmap/vprop_page freeing from its_vpe_irq_domain_alloc(). [ tglx: Massaged change log ] Fixes: 7d75bbb4bc1a ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown") Signed-off-by: Guanrui Huang Signed-off-by: Thomas Gleixner Reviewed-by: Marc Zyngier Reviewed-by: Zenghui Yu Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240418061053.96803-2-guanrui.huang@linux.alibaba.com Signed-off-by: Greg Kroah-Hartman --- drivers/irqchip/irq-gic-v3-its.c | 9 ++------- 1 file changed, 2 insertions(+), 7 deletions(-) diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c index fadd48882ef4..d16776c6dee7 100644 --- a/drivers/irqchip/irq-gic-v3-its.c +++ b/drivers/irqchip/irq-gic-v3-its.c @@ -3121,13 +3121,8 @@ static int its_vpe_irq_domain_alloc(struct irq_domain *domain, unsigned int virq set_bit(i, bitmap); } - if (err) { - if (i > 0) - its_vpe_irq_domain_free(domain, virq, i); - - its_lpi_free(bitmap, base, nr_ids); - its_free_prop_table(vprop_page); - } + if (err) + its_vpe_irq_domain_free(domain, virq, i); return err; } From 53c9574bb0f2467bc2704e18c53208668b98389a Mon Sep 17 00:00:00 2001 From: Rahul Rameshbabu Date: Tue, 23 Apr 2024 11:13:03 -0700 Subject: [PATCH 093/107] ethernet: Add helper for assigning packet type when dest address does not match device address commit 6e159fd653d7ebf6290358e0330a0cb8a75cf73b upstream. Enable reuse of logic in eth_type_trans for determining packet type. Suggested-by: Sabrina Dubroca Cc: stable@vger.kernel.org Signed-off-by: Rahul Rameshbabu Reviewed-by: Sabrina Dubroca Link: https://lore.kernel.org/r/20240423181319.115860-3-rrameshbabu@nvidia.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman --- include/linux/etherdevice.h | 25 +++++++++++++++++++++++++ net/ethernet/eth.c | 12 +----------- 2 files changed, 26 insertions(+), 11 deletions(-) diff --git a/include/linux/etherdevice.h b/include/linux/etherdevice.h index 66b89189a1e2..00d0390be91d 100644 --- a/include/linux/etherdevice.h +++ b/include/linux/etherdevice.h @@ -531,6 +531,31 @@ static inline unsigned long compare_ether_header(const void *a, const void *b) #endif } +/** + * eth_skb_pkt_type - Assign packet type if destination address does not match + * @skb: Assigned a packet type if address does not match @dev address + * @dev: Network device used to compare packet address against + * + * If the destination MAC address of the packet does not match the network + * device address, assign an appropriate packet type. + */ +static inline void eth_skb_pkt_type(struct sk_buff *skb, + const struct net_device *dev) +{ + const struct ethhdr *eth = eth_hdr(skb); + + if (unlikely(!ether_addr_equal_64bits(eth->h_dest, dev->dev_addr))) { + if (unlikely(is_multicast_ether_addr_64bits(eth->h_dest))) { + if (ether_addr_equal_64bits(eth->h_dest, dev->broadcast)) + skb->pkt_type = PACKET_BROADCAST; + else + skb->pkt_type = PACKET_MULTICAST; + } else { + skb->pkt_type = PACKET_OTHERHOST; + } + } +} + /** * eth_skb_pad - Pad buffer to mininum number of octets for Ethernet frame * @skb: Buffer to pad diff --git a/net/ethernet/eth.c b/net/ethernet/eth.c index 9040fe55e0f5..2566fff87001 100644 --- a/net/ethernet/eth.c +++ b/net/ethernet/eth.c @@ -164,17 +164,7 @@ __be16 eth_type_trans(struct sk_buff *skb, struct net_device *dev) eth = (struct ethhdr *)skb->data; skb_pull_inline(skb, ETH_HLEN); - if (unlikely(!ether_addr_equal_64bits(eth->h_dest, - dev->dev_addr))) { - if (unlikely(is_multicast_ether_addr_64bits(eth->h_dest))) { - if (ether_addr_equal_64bits(eth->h_dest, dev->broadcast)) - skb->pkt_type = PACKET_BROADCAST; - else - skb->pkt_type = PACKET_MULTICAST; - } else { - skb->pkt_type = PACKET_OTHERHOST; - } - } + eth_skb_pkt_type(skb, dev); /* * Some variants of DSA tagging don't have an ethertype field From 90be0c77571fbde60b487894a12a8e971833137e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Peter=20M=C3=BCnster?= Date: Wed, 24 Apr 2024 15:51:52 +0200 Subject: [PATCH 094/107] net: b44: set pause params only when interface is up MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e3eb7dd47bd4806f00e104eb6da092c435f9fb21 upstream. b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers) unconditionally, but b44::rx_buffers is only valid when the device is up (they get allocated in b44_open(), and deallocated again in b44_close()), any other time these are just a NULL pointers. So if you try to change the pause params while the network interface is disabled/administratively down, everything explodes (which likely netifd tries to do). Link: https://github.com/openwrt/openwrt/issues/13789 Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2) Cc: stable@vger.kernel.org Reported-by: Peter Münster Suggested-by: Jonas Gorski Signed-off-by: Vaclav Svoboda Tested-by: Peter Münster Reviewed-by: Andrew Lunn Signed-off-by: Peter Münster Reviewed-by: Michael Chan Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/broadcom/b44.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/broadcom/b44.c b/drivers/net/ethernet/broadcom/b44.c index 3e8bd454ec50..f3267983f94b 100644 --- a/drivers/net/ethernet/broadcom/b44.c +++ b/drivers/net/ethernet/broadcom/b44.c @@ -2033,12 +2033,14 @@ static int b44_set_pauseparam(struct net_device *dev, bp->flags |= B44_FLAG_TX_PAUSE; else bp->flags &= ~B44_FLAG_TX_PAUSE; - if (bp->flags & B44_FLAG_PAUSE_AUTO) { - b44_halt(bp); - b44_init_rings(bp); - b44_init_hw(bp, B44_FULL_RESET); - } else { - __b44_set_flow_ctrl(bp, bp->flags); + if (netif_running(dev)) { + if (bp->flags & B44_FLAG_PAUSE_AUTO) { + b44_halt(bp); + b44_init_rings(bp); + b44_init_hw(bp, B44_FULL_RESET); + } else { + __b44_set_flow_ctrl(bp, bp->flags); + } } spin_unlock_irq(&bp->lock); From 7d3996c74c6efa2c4389212311bacd1954f9f6c4 Mon Sep 17 00:00:00 2001 From: Andrey Ryabinin Date: Thu, 18 Apr 2024 16:11:33 +0200 Subject: [PATCH 095/107] stackdepot: respect __GFP_NOLOCKDEP allocation flag commit 6fe60465e1d53ea321ee909be26d97529e8f746c upstream. If stack_depot_save_flags() allocates memory it always drops __GFP_NOLOCKDEP flag. So when KASAN tries to track __GFP_NOLOCKDEP allocation we may end up with lockdep splat like bellow: ====================================================== WARNING: possible circular locking dependency detected 6.9.0-rc3+ #49 Not tainted ------------------------------------------------------ kswapd0/149 is trying to acquire lock: ffff88811346a920 (&xfs_nondir_ilock_class){++++}-{4:4}, at: xfs_reclaim_inode+0x3ac/0x590 [xfs] but task is already holding lock: ffffffff8bb33100 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x5d9/0xad0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (fs_reclaim){+.+.}-{0:0}: __lock_acquire+0x7da/0x1030 lock_acquire+0x15d/0x400 fs_reclaim_acquire+0xb5/0x100 prepare_alloc_pages.constprop.0+0xc5/0x230 __alloc_pages+0x12a/0x3f0 alloc_pages_mpol+0x175/0x340 stack_depot_save_flags+0x4c5/0x510 kasan_save_stack+0x30/0x40 kasan_save_track+0x10/0x30 __kasan_slab_alloc+0x83/0x90 kmem_cache_alloc+0x15e/0x4a0 __alloc_object+0x35/0x370 __create_object+0x22/0x90 __kmalloc_node_track_caller+0x477/0x5b0 krealloc+0x5f/0x110 xfs_iext_insert_raw+0x4b2/0x6e0 [xfs] xfs_iext_insert+0x2e/0x130 [xfs] xfs_iread_bmbt_block+0x1a9/0x4d0 [xfs] xfs_btree_visit_block+0xfb/0x290 [xfs] xfs_btree_visit_blocks+0x215/0x2c0 [xfs] xfs_iread_extents+0x1a2/0x2e0 [xfs] xfs_buffered_write_iomap_begin+0x376/0x10a0 [xfs] iomap_iter+0x1d1/0x2d0 iomap_file_buffered_write+0x120/0x1a0 xfs_file_buffered_write+0x128/0x4b0 [xfs] vfs_write+0x675/0x890 ksys_write+0xc3/0x160 do_syscall_64+0x94/0x170 entry_SYSCALL_64_after_hwframe+0x71/0x79 Always preserve __GFP_NOLOCKDEP to fix this. Link: https://lkml.kernel.org/r/20240418141133.22950-1-ryabinin.a.a@gmail.com Fixes: cd11016e5f52 ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB") Signed-off-by: Andrey Ryabinin Reported-by: Xiubo Li Closes: https://lore.kernel.org/all/a0caa289-ca02-48eb-9bf2-d86fd47b71f4@redhat.com/ Reported-by: Damien Le Moal Closes: https://lore.kernel.org/all/f9ff999a-e170-b66b-7caf-293f2b147ac2@opensource.wdc.com/ Suggested-by: Dave Chinner Tested-by: Xiubo Li Cc: Christoph Hellwig Cc: Alexander Potapenko Cc: Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- lib/stackdepot.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/lib/stackdepot.c b/lib/stackdepot.c index 468626b8eb1b..89ab9f14946d 100644 --- a/lib/stackdepot.c +++ b/lib/stackdepot.c @@ -259,10 +259,10 @@ depot_stack_handle_t stack_depot_save(unsigned long *entries, /* * Zero out zone modifiers, as we don't have specific zone * requirements. Keep the flags related to allocation in atomic - * contexts and I/O. + * contexts, I/O, nolockdep. */ alloc_flags &= ~GFP_ZONEMASK; - alloc_flags &= (GFP_ATOMIC | GFP_KERNEL); + alloc_flags &= (GFP_ATOMIC | GFP_KERNEL | __GFP_NOLOCKDEP); alloc_flags |= __GFP_NOWARN; page = alloc_pages(alloc_flags, STACK_ALLOC_ORDER); if (page) From 672c5715b640fcb06a25a8f6857787c6f17df5bf Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 5 Apr 2024 16:30:04 +0200 Subject: [PATCH 096/107] mtd: diskonchip: work around ubsan link failure commit 21c9fb611c25d5cd038f6fe485232e7884bb0b3d upstream. I ran into a randconfig build failure with UBSAN using gcc-13.2: arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o' I'm not entirely sure what is going on here, but I suspect this has something to do with the check for the end of the doc_locations[] array that contains an (unsigned long)0xffffffff element, which is compared against the signed (int)0xffffffff. If this is the case, we should get a runtime check for undefined behavior, but we instead get an unexpected build-time error. I would have expected this to work fine on 32-bit architectures despite the signed integer overflow, though on 64-bit architectures this likely won't ever work. Changing the contition to instead check for the size of the array makes the code safe everywhere and avoids the ubsan check that leads to the link error. The loop code goes back to before 2.6.12. Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann Signed-off-by: Miquel Raynal Link: https://lore.kernel.org/linux-mtd/20240405143015.717429-1-arnd@kernel.org Signed-off-by: Greg Kroah-Hartman --- drivers/mtd/nand/raw/diskonchip.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/nand/raw/diskonchip.c b/drivers/mtd/nand/raw/diskonchip.c index 522390b99d3c..8cbce39a33d9 100644 --- a/drivers/mtd/nand/raw/diskonchip.c +++ b/drivers/mtd/nand/raw/diskonchip.c @@ -53,7 +53,7 @@ static unsigned long doc_locations[] __initdata = { 0xe8000, 0xea000, 0xec000, 0xee000, #endif #endif - 0xffffffff }; +}; static struct mtd_info *doclist = NULL; @@ -1666,7 +1666,7 @@ static int __init init_nanddoc(void) if (ret < 0) return ret; } else { - for (i = 0; (doc_locations[i] != 0xffffffff); i++) { + for (i = 0; i < ARRAY_SIZE(doc_locations); i++) { doc_probe(doc_locations[i]); } } From 53fab9cec2cda43d7161257dad5b546ea4be0018 Mon Sep 17 00:00:00 2001 From: Kuniyuki Iwashima Date: Wed, 12 Oct 2022 07:50:36 -0700 Subject: [PATCH 097/107] tcp: Clean up kernel listener's reqsk in inet_twsk_purge() commit 740ea3c4a0b2e326b23d7cdf05472a0e92aa39bc upstream. Eric Dumazet reported a use-after-free related to the per-netns ehash series. [0] When we create a TCP socket from userspace, the socket always holds a refcnt of the netns. This guarantees that a reqsk timer is always fired before netns dismantle. Each reqsk has a refcnt of its listener, so the listener is not freed before the reqsk, and the net is not freed before the listener as well. OTOH, when in-kernel users create a TCP socket, it might not hold a refcnt of its netns. Thus, a reqsk timer can be fired after the netns dismantle and access freed per-netns ehash. To avoid the use-after-free, we need to clean up TCP_NEW_SYN_RECV sockets in inet_twsk_purge() if the netns uses a per-netns ehash. [0]: https://lore.kernel.org/netdev/CANn89iLXMup0dRD_Ov79Xt8N9FM0XdhCHEN05sf3eLwxKweM6w@mail.gmail.com/ BUG: KASAN: use-after-free in tcp_or_dccp_get_hashinfo include/net/inet_hashtables.h:181 [inline] BUG: KASAN: use-after-free in reqsk_queue_unlink+0x320/0x350 net/ipv4/inet_connection_sock.c:913 Read of size 8 at addr ffff88807545bd80 by task syz-executor.2/8301 CPU: 1 PID: 8301 Comm: syz-executor.2 Not tainted 6.0.0-syzkaller-02757-gaf7d23f9d96a #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022 Call Trace: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:317 [inline] print_report.cold+0x2ba/0x719 mm/kasan/report.c:433 kasan_report+0xb1/0x1e0 mm/kasan/report.c:495 tcp_or_dccp_get_hashinfo include/net/inet_hashtables.h:181 [inline] reqsk_queue_unlink+0x320/0x350 net/ipv4/inet_connection_sock.c:913 inet_csk_reqsk_queue_drop net/ipv4/inet_connection_sock.c:927 [inline] inet_csk_reqsk_queue_drop_and_put net/ipv4/inet_connection_sock.c:939 [inline] reqsk_timer_handler+0x724/0x1160 net/ipv4/inet_connection_sock.c:1053 call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474 expire_timers kernel/time/timer.c:1519 [inline] __run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790 __run_timers kernel/time/timer.c:1768 [inline] run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803 __do_softirq+0x1d0/0x9c8 kernel/softirq.c:571 invoke_softirq kernel/softirq.c:445 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:650 irq_exit_rcu+0x5/0x20 kernel/softirq.c:662 sysvec_apic_timer_interrupt+0x93/0xc0 arch/x86/kernel/apic/apic.c:1107 Fixes: d1e5e6408b30 ("tcp: Introduce optional per-netns ehash.") Reported-by: syzbot Reported-by: Eric Dumazet Suggested-by: Eric Dumazet Signed-off-by: Kuniyuki Iwashima Reviewed-by: Eric Dumazet Link: https://lore.kernel.org/r/20221012145036.74960-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski [shaozhengchao: resolved conflicts in 5.10] Signed-off-by: Zhengchao Shao Signed-off-by: Greg Kroah-Hartman --- net/ipv4/inet_timewait_sock.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/net/ipv4/inet_timewait_sock.c b/net/ipv4/inet_timewait_sock.c index c411c87ae865..04726bbd72dc 100644 --- a/net/ipv4/inet_timewait_sock.c +++ b/net/ipv4/inet_timewait_sock.c @@ -268,8 +268,21 @@ restart_rcu: rcu_read_lock(); restart: sk_nulls_for_each_rcu(sk, node, &head->chain) { - if (sk->sk_state != TCP_TIME_WAIT) + if (sk->sk_state != TCP_TIME_WAIT) { + /* A kernel listener socket might not hold refcnt for net, + * so reqsk_timer_handler() could be fired after net is + * freed. Userspace listener and reqsk never exist here. + */ + if (unlikely(sk->sk_state == TCP_NEW_SYN_RECV && + hashinfo->pernet)) { + struct request_sock *req = inet_reqsk(sk); + + inet_csk_reqsk_queue_drop_and_put(req->rsk_listener, req); + } + continue; + } + tw = inet_twsk(sk); if ((tw->tw_family != family) || refcount_read(&twsk_net(tw)->count)) From fc5bb10173cda1178d4e40d4cce812dadd3775c8 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 8 Mar 2024 12:01:21 -0800 Subject: [PATCH 098/107] tcp: Fix NEW_SYN_RECV handling in inet_twsk_purge() commit 1c4e97dd2d3c9a3e84f7e26346aa39bc426d3249 upstream. inet_twsk_purge() uses rcu to find TIME_WAIT and NEW_SYN_RECV objects to purge. These objects use SLAB_TYPESAFE_BY_RCU semantic and need special care. We need to use refcount_inc_not_zero(&sk->sk_refcnt). Reuse the existing correct logic I wrote for TIME_WAIT, because both structures have common locations for sk_state, sk_family, and netns pointer. If after the refcount_inc_not_zero() the object fields longer match the keys, use sock_gen_put(sk) to release the refcount. Then we can call inet_twsk_deschedule_put() for TIME_WAIT, inet_csk_reqsk_queue_drop_and_put() for NEW_SYN_RECV sockets, with BH disabled. Then we need to restart the loop because we had drop rcu_read_lock(). Fixes: 740ea3c4a0b2 ("tcp: Clean up kernel listener's reqsk in inet_twsk_purge()") Link: https://lore.kernel.org/netdev/CANn89iLvFuuihCtt9PME2uS1WJATnf5fKjDToa1WzVnRzHnPfg@mail.gmail.com/T/#u Signed-off-by: Eric Dumazet Link: https://lore.kernel.org/r/20240308200122.64357-2-kuniyu@amazon.com Signed-off-by: Jakub Kicinski [shaozhengchao: resolved conflicts in 5.10] Signed-off-by: Zhengchao Shao Signed-off-by: Greg Kroah-Hartman --- net/ipv4/inet_timewait_sock.c | 45 ++++++++++++++++------------------- 1 file changed, 21 insertions(+), 24 deletions(-) diff --git a/net/ipv4/inet_timewait_sock.c b/net/ipv4/inet_timewait_sock.c index 04726bbd72dc..85cb44bfa3ba 100644 --- a/net/ipv4/inet_timewait_sock.c +++ b/net/ipv4/inet_timewait_sock.c @@ -254,12 +254,12 @@ void __inet_twsk_schedule(struct inet_timewait_sock *tw, int timeo, bool rearm) } EXPORT_SYMBOL_GPL(__inet_twsk_schedule); +/* Remove all non full sockets (TIME_WAIT and NEW_SYN_RECV) for dead netns */ void inet_twsk_purge(struct inet_hashinfo *hashinfo, int family) { - struct inet_timewait_sock *tw; - struct sock *sk; struct hlist_nulls_node *node; unsigned int slot; + struct sock *sk; for (slot = 0; slot <= hashinfo->ehash_mask; slot++) { struct inet_ehash_bucket *head = &hashinfo->ehash[slot]; @@ -268,38 +268,35 @@ restart_rcu: rcu_read_lock(); restart: sk_nulls_for_each_rcu(sk, node, &head->chain) { - if (sk->sk_state != TCP_TIME_WAIT) { - /* A kernel listener socket might not hold refcnt for net, - * so reqsk_timer_handler() could be fired after net is - * freed. Userspace listener and reqsk never exist here. - */ - if (unlikely(sk->sk_state == TCP_NEW_SYN_RECV && - hashinfo->pernet)) { - struct request_sock *req = inet_reqsk(sk); + int state = inet_sk_state_load(sk); - inet_csk_reqsk_queue_drop_and_put(req->rsk_listener, req); - } - - continue; - } - - tw = inet_twsk(sk); - if ((tw->tw_family != family) || - refcount_read(&twsk_net(tw)->count)) + if ((1 << state) & ~(TCPF_TIME_WAIT | + TCPF_NEW_SYN_RECV)) continue; - if (unlikely(!refcount_inc_not_zero(&tw->tw_refcnt))) + if (sk->sk_family != family || + refcount_read(&sock_net(sk)->count)) continue; - if (unlikely((tw->tw_family != family) || - refcount_read(&twsk_net(tw)->count))) { - inet_twsk_put(tw); + if (unlikely(!refcount_inc_not_zero(&sk->sk_refcnt))) + continue; + + if (unlikely(sk->sk_family != family || + refcount_read(&sock_net(sk)->count))) { + sock_gen_put(sk); goto restart; } rcu_read_unlock(); local_bh_disable(); - inet_twsk_deschedule_put(tw); + if (state == TCP_TIME_WAIT) { + inet_twsk_deschedule_put(inet_twsk(sk)); + } else { + struct request_sock *req = inet_reqsk(sk); + + inet_csk_reqsk_queue_drop_and_put(req->rsk_listener, + req); + } local_bh_enable(); goto restart_rcu; } From abfe16c8e73dcf815e4efbb0c70ee9163e9f48d0 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 22 Mar 2024 14:21:07 +0100 Subject: [PATCH 099/107] dmaengine: owl: fix register access functions [ Upstream commit 43c633ef93a5d293c96ebcedb40130df13128428 ] When building with 'make W=1', clang notices that the computed register values are never actually written back but instead the wrong variable is set: drivers/dma/owl-dma.c:244:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable] 244 | u32 regval; | ^ drivers/dma/owl-dma.c:268:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable] 268 | u32 regval; | ^ Change these to what was most likely intended. Fixes: 47e20577c24d ("dmaengine: Add Actions Semi Owl family S900 DMA driver") Signed-off-by: Arnd Bergmann Reviewed-by: Peter Korsgaard Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20240322132116.906475-1-arnd@kernel.org Signed-off-by: Vinod Koul Signed-off-by: Sasha Levin --- drivers/dma/owl-dma.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/dma/owl-dma.c b/drivers/dma/owl-dma.c index bb9c361e224b..3e4ade21cf41 100644 --- a/drivers/dma/owl-dma.c +++ b/drivers/dma/owl-dma.c @@ -238,7 +238,7 @@ static void pchan_update(struct owl_dma_pchan *pchan, u32 reg, else regval &= ~val; - writel(val, pchan->base + reg); + writel(regval, pchan->base + reg); } static void pchan_writel(struct owl_dma_pchan *pchan, u32 reg, u32 data) @@ -262,7 +262,7 @@ static void dma_update(struct owl_dma *od, u32 reg, u32 val, bool state) else regval &= ~val; - writel(val, od->base + reg); + writel(regval, od->base + reg); } static void dma_writel(struct owl_dma *od, u32 reg, u32 data) From 65a241aac3c5358bd993b335782750f04f81b6cb Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Thu, 21 Mar 2024 14:04:21 +0200 Subject: [PATCH 100/107] idma64: Don't try to serve interrupts when device is powered off [ Upstream commit 9140ce47872bfd89fca888c2f992faa51d20c2bc ] When iDMA 64-bit device is powered off, the IRQ status register is all 1:s. This is never happen in real case and signalling that the device is simply powered off. Don't try to serve interrupts that are not ours. Fixes: 667dfed98615 ("dmaengine: add a driver for Intel integrated DMA 64-bit") Reported-by: Heiner Kallweit Closes: https://lore.kernel.org/r/700bbb84-90e1-4505-8ff0-3f17ea8bc631@gmail.com Tested-by: Heiner Kallweit Signed-off-by: Andy Shevchenko Link: https://lore.kernel.org/r/20240321120453.1360138-1-andriy.shevchenko@linux.intel.com Signed-off-by: Vinod Koul Signed-off-by: Sasha Levin --- drivers/dma/idma64.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/dma/idma64.c b/drivers/dma/idma64.c index f5a84c846394..db506e1f7ef4 100644 --- a/drivers/dma/idma64.c +++ b/drivers/dma/idma64.c @@ -167,6 +167,10 @@ static irqreturn_t idma64_irq(int irq, void *dev) u32 status_err; unsigned short i; + /* Since IRQ may be shared, check if DMA controller is powered on */ + if (status == GENMASK(31, 0)) + return IRQ_NONE; + dev_vdbg(idma64->dma.dev, "%s: status=%#x\n", __func__, status); /* Check if we have any interrupt from the DMA controller */ From ad3c3ac7a03be3697114f781193dd3e9d97e6e23 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 26 Apr 2024 08:44:08 +0200 Subject: [PATCH 101/107] i2c: smbus: fix NULL function pointer dereference [ Upstream commit 91811a31b68d3765b3065f4bb6d7d6d84a7cfc9f ] Baruch reported an OOPS when using the designware controller as target only. Target-only modes break the assumption of one transfer function always being available. Fix this by always checking the pointer in __i2c_transfer. Reported-by: Baruch Siach Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il Fixes: 4b1acc43331d ("i2c: core changes for slave support") [wsa: dropped the simplification in core-smbus to avoid theoretical regressions] Signed-off-by: Wolfram Sang Tested-by: Baruch Siach Signed-off-by: Sasha Levin --- drivers/i2c/i2c-core-base.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/i2c/i2c-core-base.c b/drivers/i2c/i2c-core-base.c index 964e8a29b27b..cf9ad03bb34d 100644 --- a/drivers/i2c/i2c-core-base.c +++ b/drivers/i2c/i2c-core-base.c @@ -1965,13 +1965,18 @@ static int i2c_check_for_quirks(struct i2c_adapter *adap, struct i2c_msg *msgs, * Returns negative errno, else the number of messages executed. * * Adapter lock must be held when calling this function. No debug logging - * takes place. adap->algo->master_xfer existence isn't checked. + * takes place. */ int __i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) { unsigned long orig_jiffies; int ret, try; + if (!adap->algo->master_xfer) { + dev_dbg(&adap->dev, "I2C level transfers not supported\n"); + return -EOPNOTSUPP; + } + if (WARN_ON(!msgs || num < 1)) return -EINVAL; @@ -2038,11 +2043,6 @@ int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) { int ret; - if (!adap->algo->master_xfer) { - dev_dbg(&adap->dev, "I2C level transfers not supported\n"); - return -EOPNOTSUPP; - } - /* REVISIT the fault reporting model here is weak: * * - When we get an error after receiving N bytes from a slave, From c448a9fd50f77e8fb9156ff64848aa4295eb3003 Mon Sep 17 00:00:00 2001 From: Nam Cao Date: Mon, 18 Mar 2024 11:59:02 +0100 Subject: [PATCH 102/107] HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up commit 9c0f59e47a90c54d0153f8ddc0f80d7a36207d0e upstream. The flag I2C_HID_READ_PENDING is used to serialize I2C operations. However, this is not necessary, because I2C core already has its own locking for that. More importantly, this flag can cause a lock-up: if the flag is set in i2c_hid_xfer() and an interrupt happens, the interrupt handler (i2c_hid_irq) will check this flag and return immediately without doing anything, then the interrupt handler will be invoked again in an infinite loop. Since interrupt handler is an RT task, it takes over the CPU and the flag-clearing task never gets scheduled, thus we have a lock-up. Delete this unnecessary flag. Reported-and-tested-by: Eva Kurchatova Closes: https://lore.kernel.org/r/CA+eeCSPUDpUg76ZO8dszSbAGn+UHjcyv8F1J-CUPVARAzEtW9w@mail.gmail.com Fixes: 4a200c3b9a40 ("HID: i2c-hid: introduce HID over i2c specification implementation") Cc: Signed-off-by: Nam Cao Signed-off-by: Jiri Kosina [apply to v4.19 -> v5.15] Signed-off-by: Nam Cao Signed-off-by: Greg Kroah-Hartman --- drivers/hid/i2c-hid/i2c-hid-core.c | 8 -------- 1 file changed, 8 deletions(-) diff --git a/drivers/hid/i2c-hid/i2c-hid-core.c b/drivers/hid/i2c-hid/i2c-hid-core.c index 1547b0ec6a11..fcedd1e459dc 100644 --- a/drivers/hid/i2c-hid/i2c-hid-core.c +++ b/drivers/hid/i2c-hid/i2c-hid-core.c @@ -56,7 +56,6 @@ /* flags */ #define I2C_HID_STARTED 0 #define I2C_HID_RESET_PENDING 1 -#define I2C_HID_READ_PENDING 2 #define I2C_HID_PWR_ON 0x00 #define I2C_HID_PWR_SLEEP 0x01 @@ -258,7 +257,6 @@ static int __i2c_hid_command(struct i2c_client *client, msg[1].len = data_len; msg[1].buf = buf_recv; msg_num = 2; - set_bit(I2C_HID_READ_PENDING, &ihid->flags); } if (wait) @@ -266,9 +264,6 @@ static int __i2c_hid_command(struct i2c_client *client, ret = i2c_transfer(client->adapter, msg, msg_num); - if (data_len > 0) - clear_bit(I2C_HID_READ_PENDING, &ihid->flags); - if (ret != msg_num) return ret < 0 ? ret : -EIO; @@ -540,9 +535,6 @@ static irqreturn_t i2c_hid_irq(int irq, void *dev_id) { struct i2c_hid *ihid = dev_id; - if (test_bit(I2C_HID_READ_PENDING, &ihid->flags)) - return IRQ_HANDLED; - i2c_hid_get_input(ihid); return IRQ_HANDLED; From d34a516f2635090d36a306f84573e8de3d7374ce Mon Sep 17 00:00:00 2001 From: "Matthew Wilcox (Oracle)" Date: Mon, 29 Apr 2024 15:47:51 +0100 Subject: [PATCH 103/107] bounds: Use the right number of bits for power-of-two CONFIG_NR_CPUS MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 5af385f5f4cddf908f663974847a4083b2ff2c79 upstream. bits_per() rounds up to the next power of two when passed a power of two. This causes crashes on some machines and configurations. Reported-by: Михаил Новоселов Tested-by: Ильфат Гаптрахманов Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3347 Link: https://lore.kernel.org/all/1c978cf1-2934-4e66-e4b3-e81b04cb3571@rosalinux.ru/ Fixes: f2d5dcb48f7b (bounds: support non-power-of-two CONFIG_NR_CPUS) Cc: Signed-off-by: Matthew Wilcox (Oracle) Cc: Rik van Riel Cc: Mel Gorman Cc: Peter Zijlstra Cc: Ingo Molnar Cc: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- kernel/bounds.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/bounds.c b/kernel/bounds.c index a94e3769347e..a3e1d3dfad31 100644 --- a/kernel/bounds.c +++ b/kernel/bounds.c @@ -19,7 +19,7 @@ int main(void) DEFINE(NR_PAGEFLAGS, __NR_PAGEFLAGS); DEFINE(MAX_NR_ZONES, __MAX_NR_ZONES); #ifdef CONFIG_SMP - DEFINE(NR_CPUS_BITS, bits_per(CONFIG_NR_CPUS)); + DEFINE(NR_CPUS_BITS, order_base_2(CONFIG_NR_CPUS)); #endif DEFINE(SPINLOCK_SIZE, sizeof(spinlock_t)); /* End of constants */ From 86f4a49f32e2392c97296e89da8c25e8fb482c0d Mon Sep 17 00:00:00 2001 From: Mikulas Patocka Date: Tue, 9 Jan 2024 15:57:56 +0100 Subject: [PATCH 104/107] dm: limit the number of targets and parameter size area commit bd504bcfec41a503b32054da5472904b404341a4 upstream. The kvmalloc function fails with a warning if the size is larger than INT_MAX. The warning was triggered by a syscall testing robot. In order to avoid the warning, this commit limits the number of targets to 1048576 and the size of the parameter area to 1073741824. Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer [srish: Apply to stable branch linux-5.4.y] Signed-off-by: Srish Srinivasan Signed-off-by: Greg Kroah-Hartman --- drivers/md/dm-core.h | 2 ++ drivers/md/dm-ioctl.c | 3 ++- drivers/md/dm-table.c | 9 +++++++-- 3 files changed, 11 insertions(+), 3 deletions(-) diff --git a/drivers/md/dm-core.h b/drivers/md/dm-core.h index 3fea121fcbcf..e3c3bbe92677 100644 --- a/drivers/md/dm-core.h +++ b/drivers/md/dm-core.h @@ -18,6 +18,8 @@ #include "dm.h" #define DM_RESERVED_MAX_IOS 1024 +#define DM_MAX_TARGETS 1048576 +#define DM_MAX_TARGET_PARAMS 1024 struct dm_kobject_holder { struct kobject kobj; diff --git a/drivers/md/dm-ioctl.c b/drivers/md/dm-ioctl.c index 8e787677a810..e89e710dd292 100644 --- a/drivers/md/dm-ioctl.c +++ b/drivers/md/dm-ioctl.c @@ -1760,7 +1760,8 @@ static int copy_params(struct dm_ioctl __user *user, struct dm_ioctl *param_kern if (copy_from_user(param_kernel, user, minimum_data_size)) return -EFAULT; - if (param_kernel->data_size < minimum_data_size) + if (unlikely(param_kernel->data_size < minimum_data_size) || + unlikely(param_kernel->data_size > DM_MAX_TARGETS * DM_MAX_TARGET_PARAMS)) return -EINVAL; secure_data = param_kernel->flags & DM_SECURE_DATA_FLAG; diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c index 8b05d938aa98..fcb9e2775f78 100644 --- a/drivers/md/dm-table.c +++ b/drivers/md/dm-table.c @@ -184,7 +184,12 @@ static int alloc_targets(struct dm_table *t, unsigned int num) int dm_table_create(struct dm_table **result, fmode_t mode, unsigned num_targets, struct mapped_device *md) { - struct dm_table *t = kzalloc(sizeof(*t), GFP_KERNEL); + struct dm_table *t; + + if (num_targets > DM_MAX_TARGETS) + return -EOVERFLOW; + + t = kzalloc(sizeof(*t), GFP_KERNEL); if (!t) return -ENOMEM; @@ -199,7 +204,7 @@ int dm_table_create(struct dm_table **result, fmode_t mode, if (!num_targets) { kfree(t); - return -ENOMEM; + return -EOVERFLOW; } if (alloc_targets(t, num_targets)) { From 06fdb177a02de5cbeb0af8c15cc195e2e7864ca9 Mon Sep 17 00:00:00 2001 From: Yick Xie Date: Fri, 19 Apr 2024 01:06:10 +0800 Subject: [PATCH 105/107] udp: preserve the connected status if only UDP cmsg commit 680d11f6e5427b6af1321932286722d24a8b16c1 upstream. If "udp_cmsg_send()" returned 0 (i.e. only UDP cmsg), "connected" should not be set to 0. Otherwise it stops the connected socket from using the cached route. Fixes: 2e8de8576343 ("udp: add gso segment cmsg") Signed-off-by: Yick Xie Cc: stable@vger.kernel.org Reviewed-by: Willem de Bruijn Link: https://lore.kernel.org/r/20240418170610.867084-1-yick.xie@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Yick Xie Signed-off-by: Greg Kroah-Hartman --- net/ipv4/udp.c | 5 +++-- net/ipv6/udp.c | 5 +++-- 2 files changed, 6 insertions(+), 4 deletions(-) diff --git a/net/ipv4/udp.c b/net/ipv4/udp.c index 3b3f94479885..b17b63654812 100644 --- a/net/ipv4/udp.c +++ b/net/ipv4/udp.c @@ -1054,16 +1054,17 @@ int udp_sendmsg(struct sock *sk, struct msghdr *msg, size_t len) if (msg->msg_controllen) { err = udp_cmsg_send(sk, msg, &ipc.gso_size); - if (err > 0) + if (err > 0) { err = ip_cmsg_send(sk, msg, &ipc, sk->sk_family == AF_INET6); + connected = 0; + } if (unlikely(err < 0)) { kfree(ipc.opt); return err; } if (ipc.opt) free = 1; - connected = 0; } if (!ipc.opt) { struct ip_options_rcu *inet_opt; diff --git a/net/ipv6/udp.c b/net/ipv6/udp.c index 93eb62221975..e6fdb842e89d 100644 --- a/net/ipv6/udp.c +++ b/net/ipv6/udp.c @@ -1387,9 +1387,11 @@ do_udp_sendmsg: ipc6.opt = opt; err = udp_cmsg_send(sk, msg, &ipc6.gso_size); - if (err > 0) + if (err > 0) { err = ip6_datagram_send_ctl(sock_net(sk), sk, msg, &fl6, &ipc6); + connected = false; + } if (err < 0) { fl6_sock_release(flowlabel); return err; @@ -1401,7 +1403,6 @@ do_udp_sendmsg: } if (!(opt->opt_nflen|opt->opt_flen)) opt = NULL; - connected = false; } if (!opt) { opt = txopt_get(np); From 7ae3c1fbc471b8670498e6474f55f2b2d4ea849e Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Tue, 26 Sep 2023 21:41:28 -0700 Subject: [PATCH 106/107] serial: core: fix kernel-doc for uart_port_unlock_irqrestore() commit 29bff582b74ed0bdb7e6986482ad9e6799ea4d2f upstream. Fix the function name to avoid a kernel-doc warning: include/linux/serial_core.h:666: warning: expecting prototype for uart_port_lock_irqrestore(). Prototype was for uart_port_unlock_irqrestore() instead Fixes: b0af4bcb4946 ("serial: core: Provide port lock wrappers") Signed-off-by: Randy Dunlap Cc: Thomas Gleixner Cc: John Ogness Cc: linux-serial@vger.kernel.org Cc: Greg Kroah-Hartman Cc: Jiri Slaby Reviewed-by: John Ogness Link: https://lore.kernel.org/r/20230927044128.4748-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman --- include/linux/serial_core.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index bc374d9df99f..e339dc4a500e 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -325,7 +325,7 @@ static inline void uart_port_unlock_irq(struct uart_port *up) } /** - * uart_port_lock_irqrestore - Unlock the UART port, restore interrupts + * uart_port_unlock_irqrestore - Unlock the UART port, restore interrupts * @up: Pointer to UART port structure * @flags: The saved interrupt flags for restore */ From 936e689eae3f3a77ea4dd84747a19e6a2e297d76 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Thu, 2 May 2024 16:18:37 +0200 Subject: [PATCH 107/107] Linux 5.4.275 Link: https://lore.kernel.org/r/20240430103044.655968143@linuxfoundation.org Tested-by: Shuah Khan Link: https://lore.kernel.org/r/20240430134021.555330198@linuxfoundation.org Tested-by: Florian Fainelli Tested-by: Jon Hunter Tested-by: Linux Kernel Functional Testing Tested-by: Harshit Mogalapalli Signed-off-by: Greg Kroah-Hartman --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 812c88222a76..dfb0d0dcc20b 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 VERSION = 5 PATCHLEVEL = 4 -SUBLEVEL = 274 +SUBLEVEL = 275 EXTRAVERSION = NAME = Kleptomaniac Octopus