4b9ea58bc7
[ Upstream commit d88b11ef91b15d0af9c0676cbf4f441a0dff0c56 ] This sets the partition information on the SQ201 to be read out from the RedBoot partition table, removes the static partition table and sets our boot options to mount root from /dev/mtdblock2 where the squashfs+JFFS2 resides. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
137 lines
3.0 KiB
Plaintext
137 lines
3.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Device Tree file for ITian Square One SQ201 NAS
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "gemini.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "ITian Square One SQ201";
|
|
compatible = "itian,sq201", "cortina,gemini";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory { /* 128 MB */
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
button@18 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <KEY_SETUP>;
|
|
label = "factory reset";
|
|
/* Conflict with NAND flash */
|
|
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led@20 {
|
|
label = "sq201:green:info";
|
|
/* Conflict with parallel flash */
|
|
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
led@31 {
|
|
label = "sq201:green:usb";
|
|
/* Conflict with parallel and NAND flash */
|
|
gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "usb-host";
|
|
};
|
|
};
|
|
|
|
soc {
|
|
flash@30000000 {
|
|
/*
|
|
* Flash access can be enabled, with the side effect
|
|
* of disabling access to GPIO LED on GPIO0[20] which
|
|
* reuse one of the parallel flash chip select lines.
|
|
* Also the default firmware on the machine has the
|
|
* problem that since it uses the flash, the two LEDS
|
|
* on the right become numb.
|
|
*/
|
|
/* status = "okay"; */
|
|
/* 16MB of flash */
|
|
reg = <0x30000000 0x01000000>;
|
|
|
|
partitions {
|
|
compatible = "redboot-fis";
|
|
/* Eraseblock at 0xfe0000 */
|
|
fis-index-block = <0x1fc>;
|
|
};
|
|
};
|
|
|
|
syscon: syscon@40000000 {
|
|
pinctrl {
|
|
/*
|
|
* gpio0fgrp cover line 18 used by reset button
|
|
* gpio0ggrp cover line 20 used by info LED
|
|
* gpio0kgrp cover line 31 used by USB LED
|
|
*/
|
|
gpio0_default_pins: pinctrl-gpio0 {
|
|
mux {
|
|
function = "gpio0";
|
|
groups = "gpio0fgrp",
|
|
"gpio0ggrp",
|
|
"gpio0kgrp";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sata: sata@46000000 {
|
|
cortina,gemini-ata-muxmode = <0>;
|
|
cortina,gemini-enable-sata-bridge;
|
|
status = "okay";
|
|
};
|
|
|
|
gpio0: gpio@4d000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio0_default_pins>;
|
|
};
|
|
|
|
pci@50000000 {
|
|
status = "okay";
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
|
|
<0x4800 0 0 2 &pci_intc 1>,
|
|
<0x4800 0 0 3 &pci_intc 2>,
|
|
<0x4800 0 0 4 &pci_intc 3>,
|
|
<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
|
|
<0x5000 0 0 2 &pci_intc 2>,
|
|
<0x5000 0 0 3 &pci_intc 3>,
|
|
<0x5000 0 0 4 &pci_intc 0>,
|
|
<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
|
|
<0x5800 0 0 2 &pci_intc 3>,
|
|
<0x5800 0 0 3 &pci_intc 0>,
|
|
<0x5800 0 0 4 &pci_intc 1>,
|
|
<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
|
|
<0x6000 0 0 2 &pci_intc 0>,
|
|
<0x6000 0 0 3 &pci_intc 1>,
|
|
<0x6000 0 0 4 &pci_intc 2>;
|
|
};
|
|
|
|
ata@63000000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|