This property prevents display high brightness mode from
being triggered due to HDR layers produced by camera.
Bug: 284856709
Test: can boot
Change-Id: I8ce3adb651473a5ac2f21df2132d7a44c27b413c
Add sysprops for vibrator hal to allow chirps. These props will need to
be updated with final values based on the actuator location and device
mass.
Bug: 312375018
Test: verified on device
Change-Id: Ibab38c0713c1ce39081f540f12fd6e056090ffad
Signed-off-by: Chris Paulo <chrispaulo@google.com>
Add service which will device thermal config on basis of following
conditions:
- No display panel / proto, use thermal_info_config_proto
Bug: 315096213
Test: Build and verify on all device variations
Change-Id: Ic1f652dcf38888150200bb80b35aad740058e85f
- Playback Thermal Throttle by temperature / speaker power
- BAACL
Bug: 283051989
Test: manual test
Change-Id: Iaf77a1eff58fa6f117f6d4928145cbbb5a26579f
Signed-off-by: Jasmine Cha <chajasmine@google.com>
init.zumapro.board.rc contains configurations for zumapro board
use ro.board.platform to get device board type
Bug: 311016628
Test: None
Change-Id: I90f7f01646aee8ea44ffe2a94980826b20d989ea
To avoid failures related to failure in finding inner_brightness zone
remove inner_brightness tz and related virtual sensors.
Use VSKIN-CLOSED always as VSkin for the time being.
Bug: 314912609
Test: Push config and verify boot to home and any crash
Change-Id: I195a323e1a301767953f21d2a26ea6a8917ab6f9
Due to change in power rail naming b/297343909 split the thermal info
config for proto separately from later hardware versions.
Bug: 314047297
Test: Build and verify thermal logs on proto and evt devices.
Change-Id: I9cc4570f7d983dd9b3554aea636fc50a00eefd62
For factory ROM UPH concern, we did not need TTS voice packs.
Hence, we remove them and then it could reduce super image size
and increase flash station speed.
Bug: 314245991
Test: Check super image size
Change-Id: I4ba9746c8a07c5452791d673335d07eb89abd6df
- Use Vskin equation as Vskin-Charge equation.
- Add thermal_info_config_charge
- Port wired and wireless throttling config from previous devices.
Bug: 303547723
Test: verified by emul_temp
Change-Id: I656e876d16192ec81792fd2753cdb656300687e1
To support wake gestures on the inner display.
Also remove the lockIconLongpress config since it should
not be configured for this device.
Flag: NONE
Test: manual
Fixes: 309605698
Change-Id: I9554b3c312a2e8d417280c61b227aa716d83bc22
The specs say that the status bar and nav bar should be 56dp tall when
they contain the cutout. For the status bar this is when the cutout is
at the top (rotation 0 and rotation 90). For the nav bar this is when
the cutout is at the bottom (rotation 180 and rotation 270).
The status bar and nav bar have logic to make their height to be at
least as tall as the cutout rect approximation.
Fixes: 309773362
Bug: 299908906
Test: Manual
Change-Id: I1c01280558b145280449a8c199f680c1e4304ee6
Revert submission 25284659-COMET_DISPLAY_DENSITY
Reason for revert: change density back to 390 as discussed
Reverted changes: /q/submissionid:25284659-COMET_DISPLAY_DENSITY
Change-Id: I59c1c2dcda8bf9c25fb4cb41b61e23a6930b202c
