[ Upstream commit 69f2c9346313ba3d3dfa4091ff99df26c67c9021 ]
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efcef265fd83d9a68a68926abecb3e1dd3e260a8 ]
Add the explicit error and status register fields to 'struct ata_taskfile'
using the anonymous *union*s ('struct ide_taskfile' had that for ages!) and
update the libata taskfile code accordingly. There should be no object code
changes resulting from that...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: 7390896b3484 ("ata: libata: fix NCQ autosense logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea08aec7e77bfd6599489ec430f9f859ab84575a upstream.
Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf476fe22aa1851bab4728e0c49025a6a0bea307 ]
In an unlikely (and probably wrong?) case that the 'ppi' parameter of
ata_host_alloc_pinfo() points to an array starting with a NULL pointer,
there's going to be a kernel oops as the 'pi' local variable won't get
reassigned from the initial value of NULL. Initialize 'pi' instead to
'&ata_dummy_port_info' to fix the possible kernel oops for good...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5399752299396a3c9df6617f4b3c907d7aa4ded8 ]
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ea23d5fa59f28302d4e3370c75d9c308e64410 ]
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a66307d473077b7aeba74e9b09c841ab3d399c2d upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06f6c4c6c3e8354dceddd77bd58f9a7a84c67246 upstream.
ata_dev_config_ncq_prio() and ata_dev_config_devslp() both access pages
of the IDENTIFY DEVICE data log. Before calling ata_read_log_page(),
make sure to check for the existence of the IDENTIFY DEVICE data log and
of the log page accessed using ata_identify_page_supported(). This
avoids useless error messages from ata_read_log_page() and failures with
some LLDD scsi drivers using libsas.
Reported-by: Nikolay <knv418@gmail.com>
Cc: stable@kernel.org # 5.15
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Matthew Perkowski <mgperkow@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ef63d5e14f916c5bba39128ebef395859d7c0f upstream.
If ata_read_log_page() fails to read a log page, the ata_dev_err() error
message only print the page number, omitting the log number. In case of
error, facilitate debugging by also printing the log number.
Cc: stable@kernel.org # 5.15
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Matthew Perkowski <mgperkow@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439bd25dc7b4d597cf5e4e8dc7ffc884b upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Print a list of features supported by a drive when it is configured in
ata_dev_configure() using the new function ata_dev_print_features().
The features printed are not already advertized and are: trusted
send-recev support, device attention support, device sleep support,
NCQ send-recv support and NCQ priority support.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-9-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Support for the READ LOG PAGE DMA EXT command is indicated by words 119
and 120 of a device identify data. This is tested in
ata_read_log_page() with ata_id_has_read_log_dma_ext() and the
READ LOG PAGE DMA command used if the device reports supports for it.
However, some devices lie about this support and using the DMA version
of the command fails, generating the warning message "READ LOG DMA EXT
failed, trying PIO". Since READ LOG PAGE DMA EXT is an optional command,
this warning is not at all important but may be scary for the user.
Change ata_read_log_page() to suppres this warning and to print an
error message if both DMA and PIO attempts failed.
With this change, there is no need to print again an error message when
ata_read_log_page() returns an error. So simplify the users of this
function.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-8-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ata device flag ATA_DFLAG_NCQ_PRIO indicates if a device supports
the NCQ Priority feature while the ATA_DFLAG_NCQ_PRIO_ENABLE device
flag indicates if the feature is enabled. Enabling NCQ priority use is
controlled by the user through the device sysfs attribute
ncq_prio_enable. As a result, the ATA_DFLAG_NCQ_PRIO flag should not be
cleared when ATA_DFLAG_NCQ_PRIO_ENABLE is not set as the device still
supports the feature even after the user disables it. This leads to the
following cleanups:
- In ata_build_rw_tf(), set a command high priority bit based on the
ATA_DFLAG_NCQ_PRIO_ENABLE flag, not on the ATA_DFLAG_NCQ flag. That
is, set a command high priority only if the user enabled NCQ priority
use.
- In ata_dev_config_ncq_prio(), ATA_DFLAG_NCQ_PRIO should not be cleared
if ATA_DFLAG_NCQ_PRIO_ENABLE is not set. If the device does not
support NCQ priority, both ATA_DFLAG_NCQ_PRIO and
ATA_DFLAG_NCQ_PRIO_ENABLE must be cleared.
With the above ata_dev_config_ncq_prio() change, ATA_DFLAG_NCQ_PRIO flag
is set on device scan and revalidation. There is no need to trigger a
device revalidation in ata_ncq_prio_enable_store() when the user enables
the use of NCQ priority. Remove the revalidation code from that funciton
to simplify it. Also change the return value from -EIO to -EINVAL when a
user tries to enable NCQ priority for a device that does not support
this feature. While at it, also simplify ata_ncq_prio_enable_show().
Overall, there is no functional change introduced by this patch.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-7-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce the helper functions ata_dev_config_lba() and
ata_dev_config_chs() to configure the addressing capabilities of a
device. To control message printing in these new helpers, as well as
in ata_dev_configure() and in ata_hpa_resize(), add the helper function
ata_dev_print_info() to avoid open coding for the eh context
ATA_EHI_PRINTINFO flag in multiple functions.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-6-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the code to retrieve the device sleep capability and timings out of
ata_dev_configure() into the helper function ata_dev_config_devslp().
While at it, mark the device as supporting the device sleep capability
only if the sata settings page was retrieved successfully to ensure that
the timing information is correctly initialized.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-5-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some functions have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull libata fixes from Jens Axboe:
- improve Sandisks ATA_HORKAGE on NCQ (Tejun)
- link printk cleanup (Xu)
* tag 'libata-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
libata: implement ATA_HORKAGE_MAX_TRIM_128M and apply to Sandisks
ata: ahci: use ata_link_info() instead of ata_link_printk()
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 130f4caf14 ("libata: Ensure ata_port probe has completed before
detach") may cause system freeze during suspend.
Using async_synchronize_full() in PM callbacks is wrong, since async
callbacks that are already scheduled may wait for not-yet-scheduled
callbacks, causes a circular dependency.
Instead of using big hammer like async_synchronize_full(), use async
cookie to make sure port probe are synced, without affecting other
scheduled PM callbacks.
Fixes: 130f4caf14 ("libata: Ensure ata_port probe has completed before detach")
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: John Garry <john.garry@huawei.com>
BugLink: https://bugs.launchpad.net/bugs/1867983
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Start separating SATA specific code from libata-core.c:
* move following functions to libata-sata.c:
- ata_tf_to_fis()
- ata_tf_from_fis()
- sata_link_scr_lpm()
- ata_slave_link_init()
- sata_lpm_ignore_phy_events()
* group above functions together in <linux/libata.h>
* include libata-sata.c in the build when CONFIG_SATA_HOST=y
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36762 572 40 37374 91fe drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add !IS_ENABLED(CONFIG_SATA_HOST) to ata_dev_config_ncq() to allow
compiler to optimize out the function for non-SATA configs.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36462 572 40 37074 90d2 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Separate PATA timings code from libata-core.c:
* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) select it
* move following PATA timings code to libata-pata-timings.c:
- ata_timing_quantize()
- ata_timing_merge()
- ata_timing_find_mode()
- ata_timing_compute()
* group above functions together in <linux/libata.h>
* include libata-pata-timings.c in the build when PATA_TIMINGS
config option is enabled
* cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it
depends on code from libata-core.c and libata-pata-timings.c
while its only user is ATA ACPI)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
after:
37820 572 40 38432 9620 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* fix the overly long line in ata_timing_quantize()
* use standard kernel CodingStyle in ata_timing_merge()
* do not use assignment in if condition in ata_timing_compute()
* fix non-standard comment style in ata_timing_compute()
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move EXPORT_SYMBOL_GPL()s close to exported code like it is
done in other kernel subsystems. As a nice side effect this
results in the removal of few ifdefs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Optimize struct ata_force_param size by:
- using u8 for cbl and spd_limit fields
- using u16 for lflags field
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
after:
40654 573 40 41267 a133 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use COMMAND_LINE_SIZE instead PAGE_SIZE for ata_force_param_buf[]
size as libata parameters buffer doesn't need to be bigger than
the command line buffer.
For many architectures this results in decreased libata-core.o
size (COMMAND_LINE_SIZE varies from 256 to 4096 while the minimum
PAGE_SIZE is 4096).
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 4413 40 45517 b1cd drivers/ata/libata-core.o
after:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In commit 7634ccd2da ("libata: maintainership update") from 2018
Jens has officially taken over libata maintainership from Tejun so
remove stale information from core libata code.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
device_shutdown() called from reboot or power_shutdown expect
all devices to be shutdown. Same is true for even ahci pci driver.
As no ahci shutdown function is implemented, the ata subsystem
always remains alive with DMA & interrupt support. File system
related calls should not be honored after device_shutdown().
So defining ahci pci driver shutdown to freeze hardware (mask
interrupt, stop DMA engine and free DMA resources).
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With CONFIG_DEBUG_TEST_DRIVER_REMOVE set, we may find the following WARN:
[ 23.452574] ------------[ cut here ]------------
[ 23.457190] WARNING: CPU: 59 PID: 1 at drivers/ata/libata-core.c:6676 ata_host_detach+0x15c/0x168
[ 23.466047] Modules linked in:
[ 23.469092] CPU: 59 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00010-g5b83fd27752b-dirty #296
[ 23.477776] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 23.486286] pstate: a0c00009 (NzCv daif +PAN +UAO)
[ 23.491065] pc : ata_host_detach+0x15c/0x168
[ 23.495322] lr : ata_host_detach+0x88/0x168
[ 23.499491] sp : ffff800011cabb50
[ 23.502792] x29: ffff800011cabb50 x28: 0000000000000007
[ 23.508091] x27: ffff80001137f068 x26: ffff8000112c0c28
[ 23.513390] x25: 0000000000003848 x24: ffff0023ea185300
[ 23.518689] x23: 0000000000000001 x22: 00000000000014c0
[ 23.523987] x21: 0000000000013740 x20: ffff0023bdc20000
[ 23.529286] x19: 0000000000000000 x18: 0000000000000004
[ 23.534584] x17: 0000000000000001 x16: 00000000000000f0
[ 23.539883] x15: ffff0023eac13790 x14: ffff0023eb76c408
[ 23.545181] x13: 0000000000000000 x12: ffff0023eac13790
[ 23.550480] x11: ffff0023eb76c228 x10: 0000000000000000
[ 23.555779] x9 : ffff0023eac13798 x8 : 0000000040000000
[ 23.561077] x7 : 0000000000000002 x6 : 0000000000000001
[ 23.566376] x5 : 0000000000000002 x4 : 0000000000000000
[ 23.571674] x3 : ffff0023bf08a0bc x2 : 0000000000000000
[ 23.576972] x1 : 3099674201f72700 x0 : 0000000000400284
[ 23.582272] Call trace:
[ 23.584706] ata_host_detach+0x15c/0x168
[ 23.588616] ata_pci_remove_one+0x10/0x18
[ 23.592615] ahci_remove_one+0x20/0x40
[ 23.596356] pci_device_remove+0x3c/0xe0
[ 23.600267] really_probe+0xdc/0x3e0
[ 23.603830] driver_probe_device+0x58/0x100
[ 23.608000] device_driver_attach+0x6c/0x90
[ 23.612169] __driver_attach+0x84/0xc8
[ 23.615908] bus_for_each_dev+0x74/0xc8
[ 23.619730] driver_attach+0x20/0x28
[ 23.623292] bus_add_driver+0x148/0x1f0
[ 23.627115] driver_register+0x60/0x110
[ 23.630938] __pci_register_driver+0x40/0x48
[ 23.635199] ahci_pci_driver_init+0x20/0x28
[ 23.639372] do_one_initcall+0x5c/0x1b0
[ 23.643199] kernel_init_freeable+0x1a4/0x24c
[ 23.647546] kernel_init+0x10/0x108
[ 23.651023] ret_from_fork+0x10/0x18
[ 23.654590] ---[ end trace 634a14b675b71c13 ]---
With KASAN also enabled, we may also get many use-after-free reports.
The issue is that when CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, we may
attempt to detach the ata_port before it has been probed.
This is because the ata_ports are async probed, meaning that there is no
guarantee that the ata_port has probed prior to detach. When the ata_port
does probe in this scenario, we get all sorts of issues as the detach may
have already happened.
Fix by ensuring synchronisation with async_synchronize_full(). We could
alternatively use the cookie returned from the ata_port probe
async_schedule() call, but that means managing the cookie, so more
complicated.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are several firmware versions between version 2AR10001 and
2BA30001, presumably these also have broken FPDMA_AA activation, so
lets play it safe and apply the quirk to all firmware versions.
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
