regulator: qpnp-regulator: Add snapshot of qpnp-regulator
Add snapshot of qpnp-regulator from kernel 4.9 as of commit
7262d3811169("Merge "usb: gadget: handle usb connection events").
While at it, add support for debugfs node for qpnp-regulator.
Change-Id: Ie493446009c708339af93e9d81af47b8538b8c52
Signed-off-by: Kavya Nunna <knunna@codeaurora.org>
This commit is contained in:
Kavya Nunna
@@ -1211,6 +1211,16 @@ config REGULATOR_STUB
|
||||
Consumers can use stub regulator device with proper constraint
|
||||
checking while the real regulator driver is being developed.
|
||||
|
||||
config REGULATOR_QPNP
|
||||
tristate "Qualcomm Technologies, Inc. QPNP regulator support"
|
||||
depends on SPMI
|
||||
help
|
||||
This driver supports voltage regulators in Qualcomm Technologies, Inc.
|
||||
PMIC chips which comply with QPNP. QPNP is a SPMI based PMIC
|
||||
implementation. These chips provide several different varieties of
|
||||
LDO and switching regulators. They also provide voltage switches and
|
||||
boost regulators.
|
||||
|
||||
config VIRTIO_REGULATOR
|
||||
tristate "Virtio regulator driver"
|
||||
depends on VIRTIO
|
||||
|
||||
@@ -92,6 +92,7 @@ obj-$(CONFIG_REGULATOR_RPM_SMD) += rpm-smd-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_QPNP_LCDB) += qpnp-lcdb-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_QPNP_AMOLED) += qpnp-amoled-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_QPNP) += qpnp-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
|
||||
|
||||
2449
drivers/regulator/qpnp-regulator.c
Normal file
2449
drivers/regulator/qpnp-regulator.c
Normal file
File diff suppressed because it is too large
Load Diff
189
include/linux/regulator/qpnp-regulator.h
Normal file
189
include/linux/regulator/qpnp-regulator.h
Normal file
@@ -0,0 +1,189 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-only */
|
||||
/*
|
||||
* Copyright (c) 2012-2013, 2017, 2021, The Linux Foundation. All rights reserved.
|
||||
*/
|
||||
|
||||
#ifndef __REGULATOR_QPNP_REGULATOR_H__
|
||||
#define __REGULATOR_QPNP_REGULATOR_H__
|
||||
|
||||
#include <linux/regulator/machine.h>
|
||||
|
||||
#define QPNP_REGULATOR_DRIVER_NAME "qcom,qpnp-regulator"
|
||||
|
||||
/* Pin control enable input pins. */
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN0 0x01
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN1 0x02
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN2 0x04
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN3 0x08
|
||||
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT 0x10
|
||||
|
||||
/* Pin control high power mode input pins. */
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_NONE 0x00
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN0 0x01
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN1 0x02
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN2 0x04
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN3 0x08
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_SLEEP_B 0x10
|
||||
#define QPNP_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT 0x20
|
||||
|
||||
/*
|
||||
* Used with enable parameters to specify that hardware default register values
|
||||
* should be left unaltered.
|
||||
*/
|
||||
#define QPNP_REGULATOR_DISABLE 0
|
||||
#define QPNP_REGULATOR_ENABLE 1
|
||||
#define QPNP_REGULATOR_USE_HW_DEFAULT 2
|
||||
|
||||
/* Soft start strength of a voltage switch type regulator */
|
||||
enum qpnp_vs_soft_start_str {
|
||||
QPNP_VS_SOFT_START_STR_0P05_UA,
|
||||
QPNP_VS_SOFT_START_STR_0P25_UA,
|
||||
QPNP_VS_SOFT_START_STR_0P55_UA,
|
||||
QPNP_VS_SOFT_START_STR_0P75_UA,
|
||||
QPNP_VS_SOFT_START_STR_HW_DEFAULT,
|
||||
};
|
||||
|
||||
/* Current limit of a boost type regulator */
|
||||
enum qpnp_boost_current_limit {
|
||||
QPNP_BOOST_CURRENT_LIMIT_300_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_600_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_900_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_1200_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_1500_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_1800_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_2100_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_2400_MA,
|
||||
QPNP_BOOST_CURRENT_LIMIT_HW_DEFAULT,
|
||||
};
|
||||
|
||||
/**
|
||||
* struct qpnp_regulator_platform_data - qpnp-regulator initialization data
|
||||
* @init_data: regulator constraints
|
||||
* @pull_down_enable: 1 = Enable output pull down resistor when the
|
||||
* regulator is disabled
|
||||
* 0 = Disable pull down resistor
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* pull down state
|
||||
* @pin_ctrl_enable: Bit mask specifying which hardware pins should be
|
||||
* used to enable the regulator, if any
|
||||
* Value should be an ORing of
|
||||
* QPNP_REGULATOR_PIN_CTRL_ENABLE_* constants. If
|
||||
* the bit specified by
|
||||
* QPNP_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT is
|
||||
* set, then pin control enable hardware registers
|
||||
* will not be modified.
|
||||
* @pin_ctrl_hpm: Bit mask specifying which hardware pins should be
|
||||
* used to force the regulator into high power
|
||||
* mode, if any
|
||||
* Value should be an ORing of
|
||||
* QPNP_REGULATOR_PIN_CTRL_HPM_* constants. If
|
||||
* the bit specified by
|
||||
* QPNP_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT is
|
||||
* set, then pin control mode hardware registers
|
||||
* will not be modified.
|
||||
* @system_load: Load in uA present on regulator that is not captured
|
||||
* by any consumer request
|
||||
* @enable_time: Time in us to delay after enabling the regulator
|
||||
* @ocp_enable: 1 = Allow over current protection (OCP) to be
|
||||
* enabled for voltage switch type regulators so
|
||||
* that they latch off automatically when over
|
||||
* current is detected. OCP is enabled when in HPM
|
||||
* or auto mode.
|
||||
* 0 = Disable OCP
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* OCP state
|
||||
* @ocp_irq: IRQ number of the voltage switch OCP IRQ. If
|
||||
* specified the voltage switch will be toggled off
|
||||
* and back on when OCP triggers in order to handle
|
||||
* high in-rush current.
|
||||
* @ocp_max_retries: Maximum number of times to try toggling a voltage
|
||||
* switch off and back on as a result of
|
||||
* consecutive over current events.
|
||||
* @ocp_retry_delay_ms: Time to delay in milliseconds between each
|
||||
* voltage switch toggle after an over current
|
||||
* event takes place.
|
||||
* @boost_current_limit: This parameter sets the current limit of boost type
|
||||
* regulators. Its value should be one of
|
||||
* QPNP_BOOST_CURRENT_LIMIT_*. If its value is
|
||||
* QPNP_BOOST_CURRENT_LIMIT_HW_DEFAULT, then the
|
||||
* boost current limit will be left at its default
|
||||
* hardware value.
|
||||
* @soft_start_enable: 1 = Enable soft start for LDO and voltage switch
|
||||
* type regulators so that output voltage slowly
|
||||
* ramps up when the regulator is enabled
|
||||
* 0 = Disable soft start
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* soft start state
|
||||
* @vs_soft_start_strength: This parameter sets the soft start strength for
|
||||
* voltage switch type regulators. Its value
|
||||
* should be one of QPNP_VS_SOFT_START_STR_*. If
|
||||
* its value is QPNP_VS_SOFT_START_STR_HW_DEFAULT,
|
||||
* then the soft start strength will be left at its
|
||||
* default hardware value.
|
||||
* @auto_mode_enable: 1 = Enable automatic hardware selection of regulator
|
||||
* mode (HPM vs LPM). Auto mode is not available
|
||||
* on boost type regulators
|
||||
* 0 = Disable auto mode selection
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* auto mode state
|
||||
* @bypass_mode_enable: 1 = Enable bypass mode for an LDO type regulator so
|
||||
* that it acts like a switch and simply outputs
|
||||
* its input voltage
|
||||
* 0 = Do not enable bypass mode
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* bypass mode state
|
||||
* @hpm_enable: 1 = Enable high power mode (HPM), also referred to
|
||||
* as NPM. HPM consumes more ground current than
|
||||
* LPM, but it can source significantly higher load
|
||||
* current. HPM is not available on boost type
|
||||
* regulators. For voltage switch type regulators,
|
||||
* HPM implies that over current protection and
|
||||
* soft start are active all the time. This
|
||||
* configuration can be overwritten by changing the
|
||||
* regulator's mode dynamically.
|
||||
* 0 = Do not enable HPM
|
||||
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
|
||||
* HPM state
|
||||
* @base_addr: SMPI base address for the regulator peripheral
|
||||
*/
|
||||
struct qpnp_regulator_platform_data {
|
||||
struct regulator_init_data init_data;
|
||||
int pull_down_enable;
|
||||
unsigned int pin_ctrl_enable;
|
||||
unsigned int pin_ctrl_hpm;
|
||||
int system_load;
|
||||
int enable_time;
|
||||
int ocp_enable;
|
||||
int ocp_irq;
|
||||
int ocp_max_retries;
|
||||
int ocp_retry_delay_ms;
|
||||
enum qpnp_boost_current_limit boost_current_limit;
|
||||
int soft_start_enable;
|
||||
enum qpnp_vs_soft_start_str vs_soft_start_strength;
|
||||
int auto_mode_enable;
|
||||
int bypass_mode_enable;
|
||||
int hpm_enable;
|
||||
u16 base_addr;
|
||||
};
|
||||
|
||||
#ifdef CONFIG_REGULATOR_QPNP
|
||||
|
||||
/**
|
||||
* qpnp_regulator_init() - register spmi driver for qpnp-regulator
|
||||
*
|
||||
* This initialization function should be called in systems in which driver
|
||||
* registration ordering must be controlled precisely.
|
||||
*/
|
||||
int __init qpnp_regulator_init(void);
|
||||
|
||||
#else
|
||||
|
||||
static inline int __init qpnp_regulator_init(void)
|
||||
{
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
#endif /* CONFIG_REGULATOR_QPNP */
|
||||
|
||||
#endif
|
||||
Reference in New Issue
Block a user