[ Upstream commit 530b1dbd97846b110ea8a94c7cc903eca21786e5 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 3815150a859730a267387759a1c1e086d16b8775)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
commit f78c1375339a291cba492a70eaf12ec501d28a8e upstream.
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
Cc: stable@vger.kernel.org
Fixes: 29cbe68c51 ("cfg80211/mac80211: add mesh join/leave commands")
Reported-by: syzbot+dd4779978217b1973180@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit d38d31bbbb9dc0d4d71a45431eafba03d0bc150d)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 4df49712eb54141be00a9312547436d55677f092 ]
We forgot to remove the line for snd-rtctimer from Makefile while
dropping the functionality. Get rid of the stale line.
Fixes: 34ce71a96d ("ALSA: timer: remove legacy rtctimer")
Link: https://lore.kernel.org/r/20240221092156.28695-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 0832312bae111b350330aaba1bcbae74b369e8ab)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 2df70149e73e79783bcbc7db4fa51ecef0e2022c ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734f3 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit d4d813c0a14d6bf52d810a55db06a2e7e3d98eaa)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit fccfa646ef3628097d59f7d9c1a3e84d4b6bb45e ]
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
Use the correct type instead here.
Fixes: f24c4d478013 ("efi/capsule-loader: Reinstate virtual capsule mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 00cf21ac526011a29fc708f8912da446fac19f7b)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit e4b019515f950b4e6e5b74b2e1bb03a90cb33039 ]
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc5d ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
[0] https://www.bluetooth.org/docman/handlers/DownloadDoc.ashx?doc_id=229869
Fixes: 68d19d7d9957 ("Revert "Bluetooth: validate BLE connection interval updates"")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 4debb1e930570f20caa59d815c50a89fa33124d7)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 2449007d3f73b2842c9734f45f0aadb522daf592 ]
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a5 ("Bluetooth: Perform a power cycle when receiving hardware error event")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit e0b278650f07acf2e0932149183458468a731c03)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit c68b2c9eba38ec3f60f4894b189090febf4d8d22 ]
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863fa5 ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 31e9b04a715e28aa740da64af1a3ab56373551bf)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 0e67899abfbfdea0c3c0ed3fd263ffc601c5c157 ]
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c87 ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 750e313184ea9f6866a8131c13be44f946881951)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Instead of u8, use char for prog and map name. It can avoid the
userspace tool getting compiler's signess warning. The
bpf_prog_aux, bpf_map, bpf_attr, bpf_prog_info and
bpf_map_info are changed.
Change-Id: I599a8f1eccb0d63aa8d680b771fff1580c69cf75
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During get_info_by_fd, the prog/map name is memcpy-ed. It depends
on the prog->aux->name and map->name to be zero initialized.
bpf_prog_aux is easy to guarantee that aux->name is zero init.
The name in bpf_map may be harder to be guaranteed in the future when
new map type is added.
Hence, this patch makes bpf_obj_name_cpy() to always zero init
the prog/map name.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Change-Id: Ib3bb6efbda0bd682e0cdad8617f587320d7dd397
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows userspace to specify a name for a map
during BPF_MAP_CREATE.
The map's name can later be exported to user space
via BPF_OBJ_GET_INFO_BY_FD.
Change-Id: I96b8d74b09c14f2413d421bba61cfa63d1730bc3
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds name and load_time to struct bpf_prog_aux. They
are also exported to bpf_prog_info.
The bpf_prog's name is passed by userspace during BPF_PROG_LOAD.
The kernel only stores the first (BPF_PROG_NAME_LEN - 1) bytes
and the name stored in the kernel is always \0 terminated.
The kernel will reject name that contains characters other than
isalnum() and '_'. It will also reject name that is not null
terminated.
The existing 'user->uid' of the bpf_prog_aux is also exported to
the bpf_prog_info as created_by_uid.
The existing 'used_maps' of the bpf_prog_aux is exported to
the newly added members 'nr_map_ids' and 'map_ids' of
the bpf_prog_info. On the input, nr_map_ids tells how
big the userspace's map_ids buffer is. On the output,
nr_map_ids tells the exact user_map_cnt and it will only
copy up to the userspace's map_ids buffer is allowed.
Change-Id: I85270047bd427a4f00259541a08868df62168959
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b820de741ae48ccf50dd95e297889c286ff4f760 upstream.
If kiocb_set_cancel_fn() is called for I/O submitted via io_uring, the
following kernel warning appears:
WARNING: CPU: 3 PID: 368 at fs/aio.c:598 kiocb_set_cancel_fn+0x9c/0xa8
Call trace:
kiocb_set_cancel_fn+0x9c/0xa8
ffs_epfile_read_iter+0x144/0x1d0
io_read+0x19c/0x498
io_issue_sqe+0x118/0x27c
io_submit_sqes+0x25c/0x5fc
__arm64_sys_io_uring_enter+0x104/0xab0
invoke_syscall+0x58/0x11c
el0_svc_common+0xb4/0xf4
do_el0_svc+0x2c/0xb0
el0_svc+0x2c/0xa4
el0t_64_sync_handler+0x68/0xb4
el0t_64_sync+0x1a4/0x1a8
Fix this by setting the IOCB_AIO_RW flag for read and write I/O that is
submitted by libaio.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Sandeep Dhavale <dhavale@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240215204739.2677806-2-bvanassche@acm.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 337b543e274fe7a8f47df3c8293cc6686ffa620f)
[vegard: io_uring doesn't exist in 4.14 so technically this is a no-op,
but it doesn't look like it should harm anything either -- so do like
4.19 and take it anyway. Also fix conflicts due to commit
75321b50a37a5ba612125a04bfc9e43e3da5b305 ("aio: sanitize ki_list
handling") and commit 54843f875f7a9f802bbb0d9895c3266b4a0b2f37
("aio: refactor read/write iocb setup")]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
commit 8d3a7dfb801d157ac423261d7cd62c33e95375f8 upstream.
vgic_get_irq() may not return a valid descriptor if there is no ITS that
holds a valid translation for the specified INTID. If that is the case,
it is safe to silently ignore it and continue processing the LPI pending
table.
Cc: stable@vger.kernel.org
Fixes: 33d3bc9556 ("KVM: arm64: vgic-its: Read initial LPI pending table")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240221092732.4126848-2-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c2462b26faab4d40a78fc2862387bd615e0b7c25)
[Harshit: fix conflict due to missing commit: 006df0f34930 ("KVM:
arm/arm64: Support calling vgic_update_irq_pending from irq context") in
4.14.y]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
commit db744ddd59be798c2627efbfc71f707f5a935a40 upstream.
While calculating the hardware interrupt number for a MSI interrupt, the
higher bits (i.e. from bit-5 onwards a.k.a domain_nr >= 32) of the PCI
domain number gets truncated because of the shifted value casting to return
type of pci_domain_nr() which is 'int'. This for example is resulting in
same hardware interrupt number for devices 0019:00:00.0 and 0039:00:00.0.
To address this cast the PCI domain number to 'irq_hw_number_t' before left
shifting it to calculate the hardware interrupt number.
Please note that this fixes the issue only on 64-bit systems and doesn't
change the behavior for 32-bit systems i.e. the 32-bit systems continue to
have the issue. Since the issue surfaces only if there are too many PCIe
controllers in the system which usually is the case in modern server
systems and they don't tend to run 32-bit kernels.
Fixes: 3878eaefb8 ("PCI/MSI: Enhance core to support hierarchy irqdomain")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115135649.708536-1-vidyas@nvidia.com
[ tglx: Backport to linux-4.19.y ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 343be31cc008a2f267863011934fb0aac6a9c8e2)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 0affdba22aca5573f9d989bcb1d71d32a6a03efe ]
clang-16 warns about casting between incompatible function types:
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadow.c:161:10: error: cast from 'void (*)(const struct firmware *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
161 | .fini = (void(*)(void *))release_firmware,
This one was done to use the generic shadow_fw_release() function as a
callback for struct nvbios_source. Change it to use the same prototype
as the other five instances, with a trivial helper function that actually
calls release_firmware.
Fixes: 70c0f263cc ("drm/nouveau/bios: pull in basic vbios subdev, more to come later")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240213095753.455062-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit ba9ec8d32f0f9feda6c2c044dcd72ca214485040)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit eb5c7465c3240151cd42a55c7ace9da0026308a1 ]
clang-16 notices that srpt_qp_event() gets called through an incompatible
pointer here:
drivers/infiniband/ulp/srpt/ib_srpt.c:1815:5: error: cast from 'void (*)(struct ib_event *, struct srpt_rdma_ch *)' to 'void (*)(struct ib_event *, void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1815 | = (void(*)(struct ib_event *, void*))srpt_qp_event;
Change srpt_qp_event() to use the correct prototype and adjust the
argument inside of it.
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213100728.458348-1-arnd@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit e333db03ab6ee3bd3596739724250a9a374dd466)
[vegard: fix trivial conflicts due to missing commit
10eac19bb272415cad6f28ebe8c055b648f334b1 ("IB/srpt: Fix kernel-doc
warnings in ib_srpt.c") and commit d4ee7f3a4445ec1b0b88af216f4032c4d30abf5a
("RDMA/srpt: Make debug output more detailed")]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
[ Upstream commit fdfa083549de5d50ebf7f6811f33757781e838c0 ]
Make loading ib_srpt with this parameter set work. The current behavior is
that setting that parameter while loading the ib_srpt kernel module
triggers the following kernel crash:
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
parse_one+0x18c/0x1d0
parse_args+0xe1/0x230
load_module+0x8de/0xa60
init_module_from_file+0x8b/0xd0
idempotent_init_module+0x181/0x240
__x64_sys_finit_module+0x5a/0xb0
do_syscall_64+0x5f/0xe0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Cc: LiHonggang <honggangli@163.com>
Reported-by: LiHonggang <honggangli@163.com>
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240205004207.17031-1-bvanassche@acm.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 84f1dac960cfa210a3b7a7522e6c2320ae91932b)
[vegard: drop parameter 'const' due to missing commit
e4dca7b7aa08b22893c45485d222b5807c1375ae ("treewide: Fix function
prototypes for module_param_call()")]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
commit 76c51146820c5dac629f21deafab0a7039bc3ccd upstream.
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 059285e04ebb273d32323fbad5431c5b94f77e48)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
commit 359e54a93ab43d32ee1bff3c2f9f10cb9f6b6e79 upstream.
l2tp_ip6_sendmsg needs to avoid accounting for the transport header
twice when splicing more data into an already partially-occupied skbuff.
To manage this, we check whether the skbuff contains data using
skb_queue_empty when deciding how much data to append using
ip6_append_data.
However, the code which performed the calculation was incorrect:
ulen = len + skb_queue_empty(&sk->sk_write_queue) ? transhdrlen : 0;
...due to C operator precedence, this ends up setting ulen to
transhdrlen for messages with a non-zero length, which results in
corrupted packets on the wire.
Add parentheses to correct the calculation in line with the original
intent.
Fixes: 9d4c75800f61 ("ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()")
Cc: David Howells <dhowells@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220122156.43131-1-tparkin@katalix.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4c3ce64bc9d36ca9164dd6c77ff144c121011aae)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
commit 50c70240097ce41fe6bce6478b80478281e4d0f7 upstream.
It was said that authenticated encryption could produce invalid tag when
the data that is being encrypted is modified [1]. So, fix this problem by
copying the data into the clone bio first and then encrypt them inside the
clone bio.
This may reduce performance, but it is needed to prevent the user from
corrupting the device by writing data with O_DIRECT and modifying them at
the same time.
[1] https://lore.kernel.org/all/20240207004723.GA35324@sol.localdomain/T/
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 43a202bd552976497474ae144942e32cc5f34d7e)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
commit e1a366be5cb4f849ec4de170d50eebc08bb0af20 upstream.
Commit 72f0184c8a ("mm, memcg: remove hotplug locking from try_charge")
introduced css_tryget()/css_put() calls in drain_all_stock(), which are
supposed to protect the target memory cgroup from being released during
the mem_cgroup_is_descendant() call.
However, it's not completely safe. In theory, memcg can go away between
reading stock->cached pointer and calling css_tryget().
This can happen if drain_all_stock() races with drain_local_stock()
performed on the remote cpu as a result of a work, scheduled by the
previous invocation of drain_all_stock().
The race is a bit theoretical and there are few chances to trigger it, but
the current code looks a bit confusing, so it makes sense to fix it
anyway. The code looks like as if css_tryget() and css_put() are used to
protect stocks drainage. It's not necessary because stocked pages are
holding references to the cached cgroup. And it obviously won't work for
works, scheduled on other cpus.
So, let's read the stock->cached pointer and evaluate the memory cgroup
inside a rcu read section, and get rid of css_tryget()/css_put() calls.
Link: http://lkml.kernel.org/r/20190802192241.3253165-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: cdec2e4265 ("memcg: coalesce charging via percpu storage")
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 9b78faee4829e8d4bc88f59aa125e219ad834003)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 2fe8a236436fe40d8d26a1af8d150fc80f04ee1a ]
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834 ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 07dbb1c86a81f96c779b2267ca1994f61bc1e585)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 4ce6e2db00de8103a0687fb0f65fd17124a51aaa ]
Ensure no remaining requests in virtqueues before resetting vdev and
deleting virtqueues. Otherwise these requests will never be completed.
It may cause the system to become unresponsive.
Function blk_mq_quiesce_queue() can ensure that requests have become
in_flight status, but it cannot guarantee that requests have been
processed by the device. Virtqueues should never be deleted before
all requests become complete status.
Function blk_mq_freeze_queue() ensure that all requests in virtqueues
become complete status. And no requests can enter in virtqueues.
Signed-off-by: Yi Sun <yi.sun@unisoc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240129085250.1550594-1-yi.sun@unisoc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 2b5128c714d863cd8d259aa9d87bed2d6aa6a5a8)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 7ed4380009e96d9e9c605e12822e987b35b05648 ]
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Reference: https://sourceforge.net/p/linux1394/mailman/message/58727806/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 98fc79aad9ce694cbcc202570befb8f9150cbea6)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 34cf8c657cf0365791cdc658ddbca9cc907726ce ]
Currently, coretemp driver supports only 128 cores per package.
This loses some core temperature information on systems that have more
than 128 cores per package.
[ 58.685033] coretemp coretemp.0: Adding Core 128 failed
[ 58.692009] coretemp coretemp.0: Adding Core 129 failed
...
Enlarge the limitation to 512 because there are platforms with more than
256 cores per package.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20240202092144.71180-4-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 171977332b38f271cd08dede4a792182a811a994)
[Harshit: Minor conflict due to missing commit: 9bfb375e8a2d ("hwmon:
(coretemp) Fix potentially truncated sysfs attribute name") in 4.14.y]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 4530b3660d396a646aad91a787b6ab37cf604b53 ]
Determine if the group block bitmap is corrupted before using ac_b_ex in
ext4_mb_try_best_found() to avoid allocating blocks from a group with a
corrupted block bitmap in the following concurrency and making the
situation worse.
ext4_mb_regular_allocator
ext4_lock_group(sb, group)
ext4_mb_good_group
// check if the group bbitmap is corrupted
ext4_mb_complex_scan_group
// Scan group gets ac_b_ex but doesn't use it
ext4_unlock_group(sb, group)
ext4_mark_group_bitmap_corrupted(group)
// The block bitmap was corrupted during
// the group unlock gap.
ext4_mb_try_best_found
ext4_lock_group(ac->ac_sb, group)
ext4_mb_use_best_found
mb_mark_used
// Allocating blocks in block bitmap corrupted group
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240104142040.2835097-7-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 21f8cfe79f776287459343e9cfa6055af61328ea)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 0077a504e1a4468669fd2e011108db49133db56e ]
The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.
This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.
Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.
By adjusting the port_map, the count is limited to six ports.
New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 3f25115864b2abfac4f9267475ed9419073aa560)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit e421946be7d9bf545147bea8419ef8239cb7ca52 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
In sisfb_check_var(), var->pixclock is used as a divisor to caculate
drate before it is checked against zero. Fix this by checking it
at the beginning.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
Signed-off-by: Fullway Wang <fullwaywang@outlook.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 84246c35ca34207114055a87552a1c4289c8fd7e)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit 04e5eac8f3ab2ff52fa191c187a46d4fdbc1e288 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
Although pixclock is checked in savagefb_decode_var(), but it is not
checked properly in savagefb_probe(). Fix this by checking whether
pixclock is zero in the function savagefb_check_var() before
info->var.pixclock is used as the divisor.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
Signed-off-by: Fullway Wang <fullwaywang@outlook.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 224453de8505aede1890f007be973925a3edf6a1)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ Upstream commit bcbc84af1183c8cf3d1ca9b78540c2185cd85e7f ]
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240104181059.84032-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 76fad1174a0cae6fc857b9f88b261a2e4f07d587)
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
