Add service which will device thermal config on basis of following
conditions:
- No display panel / proto, use thermal_info_config_proto
Bug: 315096213
Test: Build and verify on all device variations
Change-Id: Ic1f652dcf38888150200bb80b35aad740058e85f
- Playback Thermal Throttle by temperature / speaker power
- BAACL
Bug: 283051989
Test: manual test
Change-Id: Iaf77a1eff58fa6f117f6d4928145cbbb5a26579f
Signed-off-by: Jasmine Cha <chajasmine@google.com>
init.zumapro.board.rc contains configurations for zumapro board
use ro.board.platform to get device board type
Bug: 311016628
Test: None
Change-Id: I90f7f01646aee8ea44ffe2a94980826b20d989ea
To avoid failures related to failure in finding inner_brightness zone
remove inner_brightness tz and related virtual sensors.
Use VSKIN-CLOSED always as VSkin for the time being.
Bug: 314912609
Test: Push config and verify boot to home and any crash
Change-Id: I195a323e1a301767953f21d2a26ea6a8917ab6f9
Due to change in power rail naming b/297343909 split the thermal info
config for proto separately from later hardware versions.
Bug: 314047297
Test: Build and verify thermal logs on proto and evt devices.
Change-Id: I9cc4570f7d983dd9b3554aea636fc50a00eefd62
For factory ROM UPH concern, we did not need TTS voice packs.
Hence, we remove them and then it could reduce super image size
and increase flash station speed.
Bug: 314245991
Test: Check super image size
Change-Id: I4ba9746c8a07c5452791d673335d07eb89abd6df
- Use Vskin equation as Vskin-Charge equation.
- Add thermal_info_config_charge
- Port wired and wireless throttling config from previous devices.
Bug: 303547723
Test: verified by emul_temp
Change-Id: I656e876d16192ec81792fd2753cdb656300687e1
To support wake gestures on the inner display.
Also remove the lockIconLongpress config since it should
not be configured for this device.
Flag: NONE
Test: manual
Fixes: 309605698
Change-Id: I9554b3c312a2e8d417280c61b227aa716d83bc22
The specs say that the status bar and nav bar should be 56dp tall when
they contain the cutout. For the status bar this is when the cutout is
at the top (rotation 0 and rotation 90). For the nav bar this is when
the cutout is at the bottom (rotation 180 and rotation 270).
The status bar and nav bar have logic to make their height to be at
least as tall as the cutout rect approximation.
Fixes: 309773362
Bug: 299908906
Test: Manual
Change-Id: I1c01280558b145280449a8c199f680c1e4304ee6
Revert submission 25284659-COMET_DISPLAY_DENSITY
Reason for revert: change density back to 390 as discussed
Reverted changes: /q/submissionid:25284659-COMET_DISPLAY_DENSITY
Change-Id: I59c1c2dcda8bf9c25fb4cb41b61e23a6930b202c
The height specs of the status bar are 56dp when the camera is at the
top and 36dp when the camera is at the bottom.
To achieve this, we set the status bar height config to 36dp, which will
be used when the camera is at the bottom.
Then to achieve 56dp when the camera is at the top, we use the cutout
rect approximation, and make it 56dp in height. The height of the
status bar is adjusted to be at least as tall as the cutout rect.
+ Tweak the cutout rect, to make it be in the corner and intersect with
the top and right of the screen, which is needed for status bar inset
calculations. Before, it had a vertical offset, and was offscreen to
the right.
Now it is a rect that starts from the top right of the screen and goes
to 56dp in height and until the end of the camera in width.
Test: Manual
Fixes: 309773362
Change-Id: I9425364bab2e1413c02674cb2ae2c5be411f70c3
Vendor sched procfs path hierarchy gets updated in kernel.
Update the paths in powerhint json file to match the change.
Bug: 289151587
Test: Manual check the paths in device
Change-Id: I2c1e79c62d7e9dcd29321983e3f2a4755e916fb0
Override the config value for the comet device to make it happen.
Bug: 291870756
Test: m
Test: override the feature flag and observe
Change-Id: I887faf95391aaac268550e693bd1c38a5d290f68
