* Latest is determined by alphabetical order
* To find the .cpa file, unzip the bug report and run `tar -xvf dumpstate_board.bin`
* The .cpa file can then be found under the `camera/` directory
* This can be disabled with the prop `vendor.camera.debug.camera_performance_analyzer.attach_to_bugreport`
Bug: 191169822
Test: `adb bugreport`, unzip, `tar -xvf dumpstate_board.bin`, find expected .cpa file
Change-Id: Ie05e8d446588cebea46492b267491065161915a1
init.usb.configfs.rc has the same trigger condition of midi function.
Rename the config name to "charger" to avoid triggerring twice of the
midi function.
Bug: 188744218
Test: USB enumerated in charger mode
Signed-off-by: Kyle Tso <kyletso@google.com>
Change-Id: Ica112fb4be66356901f6d5f21b79b9e648d49f35
During Tuscany runs, the Camera HAL is requesting a CAMERA_LAUNCH power
hint, which runs big and small CPU clusters at FMAX for 1 second. This is
overkill for Tuscany, so we are requesting that the hint be removed.
Tuscany should only boost during the computationally expensive image
processing, and should stop boosting as soon as a decision is reached.
This CL adds a new power hint for Tuscany. The other CLs in this topic
use this hint to boost CPU frequency during the critical section of
Tuscany by adding a call from the FaceHAL to the PowerHAL.
Running camera open and camera close without CAMERA_LAUNCH hint saves a
measured ~1W of power. The common case for this boost in Tuscany will be
a few frames at ~60ms per frame, so much less than 1 second of boost.
The worst case scenario is falsing - no attempted unlock. We will allow
the hint to time out after 1 second in that case, but that case is less
common.
Measured latency improvement per-frame from running the CPU at FMAX is
~15ms per frame. Power measurements can be found at go/tuscany-power.
NOTE: This change will _reduce_ the power/battery impact of Tuscany by
boosting for a more precise window of time.
Bug: 190755782
Test: E2E testing, validating frequency in systrace.
Change-Id: Ibca2687d2dffa4e3d2d23a9a588a2eae0b225952
All devices use gralloc4 now, so this code is unused.
Bug: 174998182
Test: builds for the affected devices
Change-Id: Icff36a0204f7f9fd10ae7269248aef8a08c5fc1e
Setting backend thread affinity with higher uclamp value can cause
governor to clock little cores to max. Disable explicit affinity for
driver backend threads.
Fixes: 192486236
Test: build, see SF's backend threads on mid cores in gpu comp.
Change-Id: Id1b17d9783fc65f2d2541fa9c6166d771494cd42
Add powerhint configuration to use CPU 4-7 when CAMERA_LAUNCH
Bug: 188369995
Test: 1. Check camera daemon move to CPU 4-7 when camera launch
2. P21 Camera Test Checklist done
Change-Id: I6ddc9ce664166c5b78c9a5bc427c800f0714b6ea
This among other things greatly increases tethering performance.
Bug: 185092876
Test: TreeHugger, built and booted on an oriole, enabled tethering
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Change-Id: Ic9f0b4bef05250bb38c91dc1e046366098d98dc0
CAMERA_STREAMING has the setting "TAPreferHighCap=1". GCA_CAMERA_SHOT should set "TAPreferHighCap=1" as well in case user leaves the viewfinder.
We could get better performance with "HighCapacityStartCpu=6".
Bug: 192534118
Test: manual R4
Change-Id: I85c77ac1ccc2176312b54a6acdd37df55a658f04
Add MIF, INT boost powerhint configuration for CAMERA_BACKEND_BOOST to
improve stability
Bug: 168654554
Test: 1. Check clock freq related file when camera start
2. Check face id function work correctly
3. P21 Camera Test Checklist done
Change-Id: Ia39acd531063bcf93c2db9971d783f6da8006502
This variable helps the EdgeTPU components to build different
targets per target chip accordingly.
Bug: 192096682
Test: tested on local Oriole.
Change-Id: I3de4082148392b184ed7e7e40de3fa93cbfe845d
This library is hooked into the recovery code via
hardware/google/pixel/recovery and contains routines specific to the
GS101-based hardware.
Bug: 182508814
Test: did master reset on device with keys, verified no keys present after reset
Signed-off-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Harpreet Eli Sangha <eliptus@google.com>
Change-Id: I18357f5ac8db7a765a5464fd3366af3d14928ce6
This is to expose a common path to runtime.
Test: Manual. Verified edgetpu_logging works with modified path
Bug: 191193044
Signed-off-by: Erick Reyes <erickreyes@google.com>
Change-Id: I11865108931443d96389640c89b6cc29aee3a634
