Use with the new connector state during validation phase for
checking the 3d-merge topology, since this is the state that
needs to be validated.
Change-Id: Ie212f948affa4dc439ef508363bac6713e560006
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Avoid shutting down DSI PHY and lanes before entering into
idle collapse.
Change-Id: I62fb40c2398e544b08b8cb8788ac2dc1143a82ce
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
DSI PHY has various resets defined to reset analog, PLL and digital
portions. In current sequence, these resets happen after PLL is locked
which can result in introduction of jitter on PHY lanes.Reordering these
resets to happen before PLL is programmed to have intended clean start
of DSI PHY.
Change-Id: I4eb5c05ea0e6015a5447728b2845b49817411c50
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
Change the debug message to error during the writeback
encoder validate for wb output buffer. The output buffer
can be NULL only during disable frame and all other frames
need to have a valid output buffer.
Change-Id: I4d6fecfeaf863e56fe25e17ab1200849003b3309
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Add validation during crtc_atomic_check to have crtc width as
multiple of 4 when dualpipe 3d-mux is enabled and multiple of 8
when quadpipe 3d-mux is enabled. This ensures each layer mixer
is having an even width.
Change-Id: I5dc173c1b0349430a8e12a7b1c9440c7854e7ecd
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Currently, driver is determining the amount of memory to allocate
based on the event log object indexes (first, last). The last index
can change if there is additional logging done during the coredump
phase and potentially cause an out-of-bound memory access during
buffer traversal.
This change restrict the event log object traversal to a maximum
of the output buffer size.
Change-Id: I91e5734362d2d7a796129fce85e27611bab2245f
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
During MST scenario, plugging out all the downstream monitors connected
to the MST hub would trigger a disconnect handler which would cleanup
display structure. This isn't required since MST hub is still connected
and the display cleanup would be taken care during the actual MST hub
disconnect. Also, handling the disconnect immediately on port status
notification leaves the usermode in an invalid state where it assumes
the display is still enabled and results in commit errors.
Change-Id: Ia9a58fadd89bd05746da25f142b54b31e8567258
Signed-off-by: Sandeep Gangadharaiah <quic_sandgang@quicinc.com>
Currently, dnsc_blur hardware block is not updated when the connector
dnsc_blur property is set to NULL or when dnsc_blur_count is 0. Update
the dnsc_blur hw block configs to avoid stale configs affecting the
current frame.
Change-Id: I39934a8b9490a13a0f77f3b5dbc5053b76a9370b
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Use pointer and allocate dynamic memory for msm_mode_info
in _sde_crtc_check_rois instead of object to reduce the
stack memory size.
Change-Id: Ida8fc7e2b94e19b3c791dcda55a465a4107ef976
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Signed-off-by: Jeykumar Sankaran <quic_jeykumar@quicinc.com>
Addresses a race condition which could cause the RM to overcommiting LMs to
DP when multiple DP displays are used.
sde_rm_get_resource_info now uses the RM's mutex and assumes a null
encoder is not a built in display so that it can return an accurate
count of unreserved resources.
DP layer now maintains internal accounting of LMs in use to avoid
validating modes that have insufficient remaining resources.
Change-Id: I908c1597c1d651b6f9c9b74a34137f30087d8801
Signed-off-by: Alex Danila <quic_eadanila@quicinc.com>
Currently, dnsc_blur hardware block is not updated when the connector
dnsc_blur property is set to NULL or when dnsc_blur_count is 0. Update
the dnsc_blur hw block configs to avoid stale configs affecting the
current frame.
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Change-Id: If64dc5548b03edba401fb7f40edf3419dbe57ca3
Enable the clks/irqs & update RSC state during encoder disable.
This ensures RSC is in correct state during the non-primary disable
commit as it might have entered idle power collapse before the
disable.
Change-Id: Idf82efb3a7bc895e1a97c6cdeeb62970184c8e5d
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Currently previous mode information is passed to CP check phase
instead of the new incoming mode, which cause RC to silently
pass the check phase when there is a resolution mismatch between
the RC mask and new mode.
This change also adds various event log to better track RC codeflow.
Change-Id: I8953fd76e2cb0eb12e2df23038a7866edd3dcb1e
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Reset the wb crop configs from hardware, while disabling
concurrent writeback. This avoids stale configs which
affects the subsequent writeback session.
Change-Id: I4927effd0650bcdca2852a5d72c3e5478683a90f
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Currently previous mode information is passed to CP check phase
instead of the new incoming mode, which cause RC to silently
pass the check phase when there is a resolution mismatch between
the RC mask and new mode.
This change also adds various event log to better track RC codeflow.
Change-Id: I8953fd76e2cb0eb12e2df23038a7866edd3dcb1e
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Enable the clks/irqs & update RSC state during encoder disable.
This ensures RSC is in correct state during the non-primary disable
commit as it might have entered idle power collapse before the
disable.
Change-Id: Idf82efb3a7bc895e1a97c6cdeeb62970184c8e5d
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
When a display is powered off, the DP driver currently clears the aux
state and forces it to OFF, expecting a subsequent hpd_low. But in MST
scenarios it is possible for individual displays to be unplugged and then
plugged back in without disconnecting the hub. In this use case, after
the unplug of last display, the aux state is in OFF, and on the
subsequent plug-in, the driver appends the ON flag, leaving both flags
to be set which is an incorrect state. This change removes this
assumption and properly sets the ON/OFF state on enable/disable
respectively.
Change-Id: I96355938a14c77fe958b86bd5f1dabad67584e4e
Signed-off-by: Sandeep Gangadharaiah <quic_sandgang@quicinc.com>
